
Roadway excavation induces redistribution of the principal stress field in surrounding rock accompanied by rotation of the principal stress directions, which readily leads to engineering problems such as surrounding rock instability and support failures, seriously threatening the safety of soft rock roadways. To investigate the rotation characteristics of principal stresses during excavation, this study adopts the Mohr's circle spatial coordinate transformation method and establishes a critical failure criterion for soft rocks considering principal stress orientations. The evolution of principal stress magnitude and orientation is analyzed, and the mechanism of excavation-induced surrounding rock instability is revealed. Results indicate that the principal stress field experiences three stages: initial stability, severe disturbance, and new equilibrium. Stress concentration is most obvious at the two sidewalls, reaching 152% of the initial stress, with the principal stress directions restored to their initial orientations at the new equilibrium stage after serve disturbance. Principal stresses at the roof and floor are 132% and 121% of the initial stress, respectively, with the maximum and minimum principal stress directions interchanged after disturbance. Based on the rotation trajectories of principal stresses in rock masses with weak planes under different excavation directions, optimal roadway advancement directions are proposed for single, multiple, and random weak planes. The findings provide a theoretical reference for stability control of soft rock roadways. The research findings can guide the optimal advancement direction for soft soil roadways containing weak planes, providing new ideas for the stability control of surrounding rock.
In artificial ground freezing (AGF), traditional low-temperature refrigerants encounter challenges in meeting the construction demands of complex strata. This is primarily attributed to their relatively low freezing efficiency and high energy consumption. To address these issues, this paper presents a novel freezing technology based on liquid CO2. This technology enables efficient heat transfer and rapid freezing of the strata through three closed-loop circulation systems. Through a combination of in-situ experiments and numerical simulations, a systematic investigation is conducted on the evolution law of the temperature field and the reinforcement effectiveness of liquid CO2 freezing. The experimental results demonstrate that the cooling rate of this technology is four times that of traditional brine freezing. After just one day of freezing, the ground temperature can be reduced to -30℃. After 36 days of freezing, the thickness of the frozen wall reaches 3.06 m, with an average temperature of -23.9℃, and the expansion rate is 33.6 mm/d. All of these parameters are significantly superior to those of the traditional brine freezing method. By establishing a coupled hydro-thermal model, the mechanism of frozen will growth and closure is revealed. The simulation results indicate that the intersection of the frozen wall occurs after five days of freezing. Leveraging the efficient release of latent heat during phase change and the effective transfer of cooling capacity, the liquid CO2 technology not only enhances the freezing efficiency but also substantially reduces the construction cost, thereby holding great promise for engineering applications.
To investigate the coupled mechanisms of seepage, heat transfer, and mass transfer in a rough rock fracture, a three-dimensional numerical model is proposed based on the lattice Boltzmann method (LBM). The model employs three distribution functions to capture the evolution of the velocity, velocity temperature, and concentration fields, respectively accounting for the dependence of fluid kinematic viscosity, thermal diffusivity, and solute diffusivity on temperature. Model accuracy is verified against two benchmark cases. The model is subsequently applied to investigate the effects of rock temperature, pressure gradient, and fracture roughness on solute transport within fractures. A comprehensive sensitivity evaluation analysis is performed to evaluate the overall sensitivity of five key influencing factors: parameters: fracture aperture, pressure gradient, rock temperature, fracture roughness, and initial solute diffusion coefficient. The results reveal that increasing rock temperature reduces the kinematic viscosity of the fluid while enhancing the solute diffusion coefficient, thereby significantly accelerating solute transport in the rock fracture. Specifically, when rock temperature rises from 20℃ to 70℃, kinematic viscosity decreases to 48% of its initial value, while the solute diffusion coefficient increases to 5.17 times its initial value. Higher seepage velocity further promotes solute transport through the coupling effect between flow velocity and temperature. However, increased flow velocity partially offsets the temperature-induced acceleration. In the near-wall regions of fractures, solute transport exhibits higher sensitivity to temperature variations, with temperature exerting a more pronounced control than the pressure gradient. Increasing fracture roughness leads to reduced fluid velocity and elevated temperature within the fracture. The deceleration of flow exerts a substantially greater inhibitory effect on solute transport than the enhancement of diffusion arising from temperature elevation. Consequently, greater fracture roughness results in slower solute transport. Among all investigated factors, fracture aperture exhibits the highest sensitivity, whereas the initial solute diffusion coefficient shows the lowest sensitivity.
To analyze the influence of reinforcement on the strength of expansive soil under dry-wet cycles, small-sized conventional cutting ring specimens, vertically reinforced at mid-height at are prepared by a two-stage compaction method, and direct shear tests are conducted in the direction perpendicular to the reinforcement mesh. Direct shear tests covering the low normal stress range under five dry-wet cycles are carried out on unreinforced expansive soil and reinforced expansive soil, and the changes in cracks of expansive soil during the cycles are observed. The test results indicate that the cohesion of reinforced expansive soil is significantly improved and basically remained unchanged under dry-wet cycles, while the variation range of the internal friction angle after reinforcement is small. A strength prediction method for conventional large-sized geogrid-reinforced expansive soil under dry-wet cycles is proposed. The variation patterns of surface crack ratio and volumetric crack ratio during dry-wet cycles, as well as the role of reinforcement in inhibiting crack development and strength degradation, are analyzed. The volumetric rack ratio is proposed as an effective indicator for predicting soil strength parameters. The research results can provide a reference for further revealing the mechanism of reinforcement in improving the stability of expansive soil slopes.
The longitudinal joints of the segmental lining in pressurized water-conveyance tunnels are typically characterized by detailed configurations such as double-row bolts, multiple waterproofing measures, and edge gaps. Their flexural performance affects the overall mechanical response of the structure. To analyze the influence of detailed structural features on the flexural performance of the joint, this study constructs a joint flexural mechanical model, establishes the joint mechanical equilibrium equations based on the opening process, and validates against full-scale tests. The effects of the arrangements of bolts and waterproof grooves on the flexural performance of the joint are emphatically analyzed. The results show that the bending moment-rotation curve of the joint presents an S-shaped distribution. The flexural stiffness of the joint exhibits an overall nonlinear degradation trend as the joint opens. The presence of edge gaps reduces the initial flexural stiffness, while gap closure enhances the flexural performance. The ultimate flexural bearing capacity of the joint is optimal under a certain edge gap, with a more significant improvement under low axial force conditions. The double-row bolt arrangement significantly enhances the flexural performance on both sides of the joint. For example, under an axial force of 2 MN, the positive and negative ultimate bending moments are increased by 215.0% and 91.6%, respectively, compared with the boltless scheme; the positive ultimate bending moment is increased by 120.5% compared with the outer single-row bolt scheme, and the negative ultimate bending moment is increased by 67.9% compared with the inner single-row bolt scheme. Adjusting the bolts properly toward the segment edge can improve the same-side flexural performance.