
It has been widely recognized that traversing vehicles can dampen bridge vibrations. This work clarifies the efficacy of different vehicle suspension tuning approaches for bridge vibration mitigation using an equivalent tuned mass damper (TMD) model and presents a parametric analysis of the key physical factors governing vehicle-bridge interaction. The vehicle-bridge system is modelled as a TMD traveling on an elastically supported beam. A finite element model is developed to numerically validate the analytical model. Transmissibility functions, obtained using the time-freezing technique, and complex eigenvalue loci are employed in the tuning process. For an undamped bridge, the optimal stiffness and damping ratio of the vehicle suspension are obtained from an extended fixed-point principle, under which the analytical model is equivalent to a smooth bridge coupled to a TMD and subjected to a harmonic transverse excitation at the contact point. For a damped bridge, the optimal vehicle suspension parameters are determined from the intersection of the eigenvalue loci of the system. Vehicle damping can induce curve veering of the instantaneous coupled eigenvalues during the vehicle passage, and this phenomenon is further examined through a perturbation analysis. In the parametric analysis, the root-mean-square values of the kinetic and potential energy of the bridge are used to quantify the vibration mitigation performance. Tuning at bridge midspan generally achieves the greatest bridge energy reduction under both sinusoidal and stochastic excitations, since the maximum bridge displacement occurs at that position. Among the considered tuning methods, the optimal parameters determined by enforcing a zero gradient at the fixed point of the fundamental bridge frequency and equal transmissibility magnitudes at the other two fixed points are shown to be the most effective. Based on the midspan tuning strategy, a parametric study of the sprung mass, vehicle speed, excitation frequency, surface roughness class, bridge damping, and bearing stiffness is performed, which reveals the importance of frequency match and phase lag between the bridge and the vehicle in mitigating the bridge responses. The present study also shows that bridge surface roughness can significantly influence the efficacy of vibration mitigation.
The geometric degrees of freedom of non-circular gears provide a means for continuously tuning mechanical metamaterials. However, the relationship between pitch design and load-bearing and vibration responses still needs to be clarified. In this paper, we construct a mechanical metamaterial consisting of a fourth-order non-circular sun gear, a sixth-order non-circular ring gear, and four cylindrical planet gears, using the sun gear’s angular position as the configuration control variable. By using high-order elliptic pitch curves and enveloping-generated tooth surfaces, we transform the rotational input into changes in the ring gear's support positions and the effective bending span. Simulations of contact motion and finite element analysis jointly reveal the relationship between geometric encoding, support migration, and load path reconstruction. During combined compression and rotation, the equivalent compressive modulus in the gauge region varies between 5.15 and 117.96 GPa, with a tuning ratio of 22.9. The 2×2 and 3×3 finite arrays preserve configuration-dependent stress migration through shared walls and facilitate load sharing between unit cells. Modal and harmonic response analyses of fixed configurations indicate that the angle of rotation simultaneously alters the distribution of mode shapes as well as the positions of resonance peaks and anti-resonance troughs. These results link non-circular gear geometry with configuration-dependent mechanics, providing a design basis for continuous stiffness adjustment and vibration response control in load-bearing structures.
This study examines the mechanical properties of trichiral (TC), antitrichiral (ATC), and reentrant antitrichiral (ATCR) networks when subjected to tensile, compression, and bending loads. The experimental data indicate that tensile properties are governed primarily by geometry, while compressive and bending performance are also influenced by relative density. The trichiral network shows the highest tensile stiffness, with Young’s moduli of 18[Formula: see text]MPa (single-cell) and 150[Formula: see text]MPa (two-cell). The antitrichiral and reentrant antitrichiral geometries exhibit lower stiffness (120[Formula: see text]MPa and 40[Formula: see text]MPa, respectively) but display negative Poisson’s ratios, indicating auxetic behavior. In compression, the antitrichiral network yielded the best results with a compression modulus of 105[Formula: see text]MPa and showed energy absorption up to 40% greater than the other geometries. Bending tests demonstrate that the antitrichiral sandwich structure carries a larger load due to the higher density of the structure, despite some minor variation due to 3D printing. These results demonstrate that geometry, rather than the density, governs the mechanical performance of architected materials. The trichiral topology is excellent for a lightweight, high-stiffness design, while the antitrichiral design provides superior energy absorption.
Auxetic-core sandwich structures have attracted increasing attention due to their unconventional deformation mechanisms and their potential to enhance mechanical performance. This study investigates the influence of auxetic core topology on the static and fatigue flexural behavior of biocomposite sandwich structures fabricated using fused deposition modeling (FDM) with flax-fiber-reinforced polylactic acid (PFF). Six distinct architected core topologies were investigated: single and double auxetic, single and double arc, dumbbell, and infinity configurations. Static three-point bending and flexural fatigue tests were conducted to evaluate flexural stiffness, strength, fatigue life, and dynamic response. The results reveal that core topology significantly influences both the static mechanical properties and fatigue performance of the sandwich structures under flexural loading. The S-DARC configuration exhibited the highest flexural stiffness and longest fatigue life, whereas the S-SARC and S-DAUX configurations achieved the highest flexural strengths. The S-SAUX configuration demonstrated a high energy dissipation capacity but exhibited greater sensitivity to the applied fatigue loading level. Overall, these findings highlight the critical role of core topology in tailoring the static and fatigue flexural performance of additively manufactured biocomposite sandwich structures to meet specific engineering requirements.
This study develops a coupled nonlinear thermomechanical finite element model for the bending analysis of composite laminated plates containing shape memory alloy wire-reinforced hybrid composite (SMAHC) layers. The formulation is established based on higher-order layerwise (HOLW) mechanics and Brinson’s one-dimensional SMA constitutive model with phase-transformation kinetics. A micro/macro mixture-type homogenization scheme is incorporated to evaluate the effective properties and recovery-stress contributions of the SMAHC lamina, which are consistently updated according to the evolving martensitic volume fraction during the nonlinear solution. The governing equations are solved using a Newton-Raphson iterative procedure, enabling step-by-step tracking of SMA phase transformation during loading and unloading. By enriching the through-thickness displacement field at the layer level, the proposed formulation improves the prediction of bending responses of SMAHC laminates, including higher-order through-thickness variations and interlaminar stress transfer. The accuracy and effectiveness of the method are assessed through convergence studies, comparison with three-dimensional elasticity benchmarks and experimental results. Parametric studies are then performed to investigate the effects of temperature, boundary conditions, peak load, SMA pre-strain, stacking sequence, and SMA wire volume fraction on the global hysteretic bending response and the associated martensite evolution.