
Abstract A modified incremental harmonic balance (IHB) method is employed to obtain periodic solutions for wave propagation in a strongly nonlinear mass-in-mass chain with hard springs. To analyze the stability and bifurcations of the solutions, a method based on Hill’s method is utilized. This study first reveals possible types of solutions and verifies that the solutions are in a hyperplane with two dimensions. Furthermore, relationships among the amplitude, the frequency, and system parameters are thoroughly analyzed and numerous bifurcations are identified. Two frequency formulae for wave propagation in a weakly and strongly nonlinear mass-in-mass chain with hard springs are derived using a fitting method and the modified IHB method. Notably, the formulae for weak nonlinearity are consistent with the formula obtained via the Lindstedt–Poincaré (LP) method. Finally, attenuation zones for optical and acoustic branches are identified.
A dynamical model governing the motion of a double-supported water-filled rectangular container conveyed by an overhead crane is proposed. The internal water is modeled as two parts: a moving part represented by a pendulum system and a rigid body that swings with the container. The mathematical model is validated against a finite-element model incorporating fluid-structure interaction. An open-loop input-shaping technique is employed for fast rest-to-rest maneuvering, using two multimode shapers: the convolved and simultaneous input shapers. The system's natural frequencies from the linearized model are utilized to design the multimode input shapers. Finite-element simulations and experimental results from a constructed setup of the double-supported water-filled rectangular container model confirm the necessity of considering all vibrational modes to eliminate residual vibrations and suppress sloshing. Sensitivity analyses highlight the importance of robust input shapers in managing system nonlinearities. Key differences between the controllers in terms of design process, shaper's duration, number of generated impulses in their sequences, sloshing suppression, and robustness against water depth variations are discussed.
Measuring the natural frequencies and mode shapes of rotating turbomachinery components under real-operating conditions is particularly important to prevent dangerous operating scenarios. However, this task becomes particularly challenging for runners and impellers because they are rotating, confined, and, in hydraulic turbomachinery, submerged. Furthermore, many existing measurement techniques rely on frequency-domain analysis, where measurements taken from the stationary frame can produce complex spectral responses that complicate interpretation. To address these challenges, this work proposes a method to extract excited mode shapes and their associated vibration frequencies directly from time-domain signals. Mode shapes are recovered through demodulation of the structural response measured once the system reaches a resonant state. Measurements are performed using a laser Doppler vibrometer (LDV) in the stationary frame. To validate the method, a simplified model representing an axial turbomachinery impeller or runner is studied both experimentally and numerically. First, modal analyses under stationary (non-rotating) conditions are conducted to identify the natural frequencies and mode shapes. The structure is then set into rotation and brought to resonance using a piezoelectric actuator, with response measured by the LDV in the stationary frame and by an accelerometer installed in the rotating frame. The proposed method demonstrates the feasibility of accurately extracting mode shapes in complex rotating systems and provides valuable insights for resonance detection and monitoring of such structures. Limitations and potential applications of the methodology are also discussed.
This article systematically investigates the isolation performance of a double-beam system interconnected by a nonlinear X-shaped connector. Based on Hamilton's principle and geometric analysis, a dynamic model of the system is derived. This model is used to explore the sensitivity of vibration suppression performance to key parameters, including the tuning ratio and connector design. The analytical findings are subsequently validated through finite-element simulations, ensuring consistency between theoretical predictions and numerical results. The theoretical findings demonstrate that: (a) compared to linear connectors, the nonlinear X-shaped connector enables the double-beam system more effectively isolate vibration transmission between flexible bodies and perform better under large-amplitude excitations by utilizing the geometric nonlinearity of the connector; (b) their adjustable parameters allow flexible tuning to meet vibration reduction needs in various environments; (c) an unequal-length design of the upper and lower beams improves vibration control; (d) adapting the system's tuning ratio according to excitation frequency yields superior vibration attenuation. This research proposes a potential method for the vibration isolation of continuous systems utilizing bio-inspired nonlinear characteristics.
This study addresses the challenging issue of analytical modeling of forced vibration of rectangular plates in thermal environments, which involves mathematical difficulties in treating complex boundary value problems in higher-order partial differential equations. An effective symplectic superposition method is extended for the present issue, focusing on non-L & eacute;vy-type boundary conditions that were not accurately analyzed by conventional analytical methods. To be specific, an original problem is decomposed into three subproblems, which are solved rigorously through separation of variables followed by symplectic eigen expansion, and the original problem's solution is determined by superposing the subproblems' solutions. Various forced vibration results under different thermal environments and different harmonic load scenarios are presented, showing good agreement with finite element numerical simulation results. Furthermore, the effects of temperature variation, harmonic frequency, simple harmonic load amplitude, and boundary conditions, among others, on the thermal vibration characteristics are explored. The findings delve into the significant impact of thermal environments on the forced vibration performance of rectangular plates, offering a theoretical basis for related structural designs.