
This study analyzes the vibrational characteristics of functionally graded piezoelectric-elastic (FGPE) annular nanoplates under rotational and thermal loads. The material system consists of piezoelectric (BaTiO3) and non-piezoelectric elastic (CoFe2O4) phases. The thermo-electro-elastic properties of the nanoplate vary continuously along its thickness according to a power-law distribution. The analysis employs the nonlocal strain gradient theory (NSGT), the governing equations are derived using Hamilton's principle and solved via the Runge-Kutta method. Results demonstrate that: The natural frequency exhibits complex behavior influenced by rotational speed, initially decreasing, then increasing, and subsequently fluctuating. Increasing the functionally graded index or porosity volume fraction reduces the natural frequency by softening material stiffness and weakening piezoelectric coupling efficiency. The electric potential enhances frequency at low rotational speeds but induces complex fluctuations beyond a critical speed. Temperature changes cause a non-monotonic frequency response, initially decreasing, then increasing, and finally decreasing again. Clearly, initial geometric imperfection significantly alter the vibration characteristics, with frequency decreasing at low speeds, increasing beyond a critical rotational speed, and decreasing again at higher speeds, highlighting the importance of accounting for geometric imperfections in nanoscale structural design.
Stay cables in cable-stayed bridges often experience high-nonlinear vibrations under complex end excitations during strong earthquakes, resulting in severe damage to their seismic safety. Conventional discretized truss element models for simulating large-deformation cable vibrations frequently suffer from reduced accuracy, decreased computational efficiency, and numerical divergence. This study proposes an improved multi-element model (MT-EBCE) in OpenSees, which combines a truss element and an elastic beam-to-column element between multiple sharing nodes to compute coupled cable responses. Its superior computational accuracy and efficiency are validated against mainstream multi-element models. Subsequently, based on the improved MT-EBCE cable model, a numerical analysis is conducted to investigate the nonlinear vibration characteristics of stay cables under multidirectional and multi-frequency coupled complex end excitations. The results demonstrate that the improved MT-EBCE model can effectively simulate loosening and fracture phenomena of the cable. The response characteristics of cables subjected to multi-directional and multi-frequency coupled excitations cannot be obtained through superposition from individual inputs. In some cases, calculations based on simple superposition may underestimate the cable displacement response by up to 50% compared to the true value under complex end excitation. Therefore, it is necessary to utilize the improved MT-EBCE model to conduct nonlinear vibration characteristic analysis for cables under complex end excitations.
In this study, a simplified design method for shear wall-frame systems based on the Direct Displacement-Based Design (DDBD) approach is proposed. The method is developed using a continuous-system analytical model. For this purpose, an equivalent flexural-shear beam model is formulated based on the assumption that the frame shear force remains constant over the height of the building. By solving the differential equation governing the equivalent flexural-shear beam and applying equilibrium conditions, analytical relationships are derived for the effective mass, effective height, wall base moment ratio, and the location of the wall moment inflection point. Based on these relationships, practical design tables and charts are developed to illustrate the variation of the effective mass, effective height, wall base moment ratio, and wall moment inflection point with the frame shear ratio (defined as the ratio of the frame base shear to the total base shear). These design aids allow rapid estimation of the key design parameters required for DDBD applications. The proposed flexural-shear beam model extends the application of DDBD and enables the design of wall-frame systems to be carried out more efficiently and in a shorter time than conventional DDBD procedures. To evaluate the applicability of the proposed approach, a series of design examples was examined. The first example was presented in detail to facilitate a clearer understanding of the design procedure. The results indicate that the proposed method yields sufficiently accurate and reliable results for preliminary design applications. Consequently, the proposed approach provides a practical and efficient framework for the Displacement-Based Design (DBD) of wall-frame systems.
This study presents a combined finite element and component mode synthesis (FEM-CMS) approach for the vibration and stability analysis of a cracked tapered Euler-Bernoulli beam with linearly varying thickness, constant width, and a single open edge crack subjected to axial compressive loading. The crack is modeled as a massless rotational spring through a local flexibility matrix derived from fracture mechanics principles, and the cracked beam is treated as an assembly of subcomponents coupled by the crack stiffness matrix. Both clamped-free and pinned-pinned boundary conditions are considered, and parametric investigations are conducted over crack depth ratios (a/b=0.2-0.8), crack locations (Lc/L=0.1-0.9), thickness ratios (t2/t1=0.5-0.9), and normalized axial load levels (P/Pcr=0-0.9). The results demonstrate that crack-induced reductions in both buckling capacity and natural frequencies are strongly governed by the spatial correspondence between the crack location and the region of maximum bending moment of the associated mode shape, and that the boundary condition fundamentally alters the spatial distribution of crack sensitivity. For the clamped-free beam, a deep crack (a/b=0.8) near the fixed end reduces the critical buckling load by approximately 66%; for the pinned-pinned beam, the most critical position shifts to mid-span, where a similar crack produces a 70% reduction. The applied axial load amplifies crack-induced frequency reductions in a strongly nonlinear manner at high load ratios, particularly in the fundamental vibration mode. The present findings provide a systematic quantitative framework for vibration-based damage assessment in non-uniform beam structures subjected to compressive loading.
This study presents a practical multi-objective optimization framework for 3D reinforced concrete (RC) moment-resisting frames using NSGA-II. Its main novelty is a decoupled genetic encoding of column rotation angles (0 degrees/90 degrees), combined with a section database that embeds ACI 318-19 reinforcement detailing-crossties, skin reinforcement, and seismic hooks-directly as discrete design variables. Two objectives are minimized: a normalized sum of total construction cost and embodied CO2, and the maximum inter-story drift ratio. On 4-, 6-, and 8-story irregular benchmark frames, the decoupled approach (Scenario A) attains a 4.5% higher Hypervolume and up to 22% lower cost at equal drift than the conventional coupled approach (Scenario B), and ten independent runs confirm convergence robustness. Construction cost and embodied CO2 are found to be almost perfectly correlated (R-2 >= 0.99), so the effective trade-off is between the combined cost-carbon objective and drift; the study also quantifies how the design freedom of this trade-off contracts as building height increases.