Abstract The current generation of gravitational wave detectors revolutionised the scientific community with the first direct detection of gravitational waves in 2015. The next generation of detectors will utilise innovative techniques to improve detector sensitivity, with prototype interferometer facilities are of fundamental importance to investigate and realise these technologies. One prototype working to this goal is the Glasgow Cryogenic Interferometer Facility. This facility will utilise a double-cavity configuration with cryogenic silicon optics to demonstrate necessary technologies for these next-generation detectors. This work outlines a design for the cryogenic silicon suspension and details the ongoing experimental work at the facility.

Abstract With the plans for the Einstein Telescope to operate at cryogenic temperatures, there is a need for low-noise crystalline suspension systems to reach the required sensitivity goals. Crystalline silicon is a promising candidate for suspension elements due to its favourable properties at cryogenic temperatures, including a high-quality factor, thermoelastic nulling regions, and thermal conductivity. It has been shown that these properties, as well as mechanical strength, are dependent on the surface quality and fabrication process of the material. An optimized production process for crystalline fibers is therefore crucial, along with thorough characterization of their properties. In this study, we present the characterisation of crystalline silicon fibres grown using the float-zone technique by the Institut füur Kristallzüuchtung (IKZ) Berlin. These initial results demonstrate the potential feasibility of producing high-quality silicon fibres and indicate that, with further optimisation and characterisation, silicon fibres have the potential to achieve the necessary low thermal noise performance, reinforcing silicon’s suitability as a candidate material for next-generation gravitational wave detectors.

We present the results of a search for gravitational-wave transients associated with core-collapse supernova SN 2023ixf, which was observed in the galaxy Messier 101 via optical emission on 2023 May 19, during the LIGO–Virgo–KAGRA 15th Engineering Run. We define a five-day on-source window during which an accompanying gravitational-wave signal may have occurred. No gravitational waves have been identified in data when at least two gravitational-wave observatories were operating, which covered ∼14% of this five-day window. We report the search detection efficiency for various possible gravitational-wave emission models. Considering the distance to M101 (6.7 Mpc), we derive constraints on the gravitational-wave emission mechanism of core-collapse supernovae across a broad frequency spectrum, ranging from 50 Hz to 2 kHz, where we assume the gravitational-wave emission occurred when coincident data are available in the on-source window. Considering an ellipsoid model for a rotating proto-neutron star, our search is sensitive to gravitational-wave energy 1 × 10 −4 M ⊙ c 2 and luminosity 2.6 × 10 −4 M ⊙ c 2 s −1 for a source emitting at 82 Hz. These constraints are around an order of magnitude more stringent than those obtained so far with gravitational-wave data. The constraint on the ellipticity of the proto-neutron star that is formed is as low as 1.08, at frequencies above 1200 Hz, surpassing past results.

We present results from a search for X-ray/gamma-ray counterparts of gravitational-wave (GW) candidates from the third observing run (O3) of the LIGO-Virgo-KAGRA network using the Swift Burst Alert Telescope (Swift-BAT). The search includes 636 GW candidates received with low latency, 86 of which have been confirmed by the offline analysis and included in the third cumulative Gravitational-Wave Transient Catalogs (GWTC-3). Targeted searches were carried out on the entire GW sample using the maximum-likelihood Non-imaging Transient Reconstruction and Temporal Search pipeline on the BAT data made available via the GUANO infrastructure. We do not detect any significant electromagnetic emission that is temporally and spatially coincident with any of the GW candidates. We report flux upper limits in the 15-350 keV band as a function of sky position for all the catalog candidates. For GW candidates where the Swift-BAT false alarm rate is less than 10(-3) Hz, we compute the GW-BAT joint false alarm rate. Finally, the derived Swift-BAT upper limits are used to infer constraints on the putative electromagnetic emission associated with binary black hole mergers.

Upgrades to ground-based gravitational-wave observatories will require mirror coatings with reduced thermal noise, enabling improved detector sensitivity and extended astrophysical reach. Recent studies have shown that optical coatings utilising amorphous materials that exhibit a larger fraction of corner-sharing between adjacent structural units of metal-centered polyhedra are a promising route for reducing mechanical dissipation and thus thermal noise at room temperature. We report on multilayer optical coatings that are fabricated using germanium dioxide mixed with titanium dioxide (TiO_2:GeO_2) for the high index layers, and silicon dioxide (SiO_2) for the low index material. Single layers of TiO_2:GeO_2 are characterised to optimise the mixture proportion and based on that highly reflective multilayer stacks were deposited. Exceptional optical absorption at 1064 nm below 1 part-per-million (ppm) is observed in the multilayer stacks after heat treatment. The annealing process also induces the formation of blisters which leads to increased optical scattering. However, there is indication that blisters can be suppressed by decreasing the water partial pressure in the deposition chamber. Direct thermal noise measurements provide experimental verification of a significant 25% reduction of thermal noise over the mirrors currently employed, which combined with sub-ppm levels of optical absorption show the potential of TiO_2:GeO_2 to improve the sensitivity of gravitational-wave observatories.

Current generation gravitational wave detectors rely on ultra-high purity fused silica in the final monolithic stage of the mirror suspension systems for their excellent thermal noise performance. There is however a push to develop cryogenic suspension systems for the next generation detectors, where fused silica loses its superior thermal noise properties. Silicon is an attractive candidate material, and is the baseline design selected for use in the cryogenic Einstein Telescope and brings with it a new set of challenges. This paper outlines what the authors believe to be the world’s first demonstration of a single ribbon hydroxy-catalysis bonded silicon suspension that has cycled between room temperature and a 4 K environment. Also discussed is the characterisation of similar silicon ribbon, detailing work on surface treatments used to improve the ultimate tensile strength alongside the thermal conductivity of the silicon suspension.

Due to its excellent optical properties, such as low absorption and scattering, amorphous Ta2O5 is commonly used as an optical coating material, often in combination with SiO2 layers to produce a highly reflective stack. However, the high mechanical loss of Ta2O5 limits the thermal-noise performance of such coatings when used in precision measurement applications. Doping with TiO2 has previously been shown to slightly reduce the mechanical loss, but it is still very high compared to many other materials, particularly at low temperatures. In this paper, we present a detailed study of different heat treatment temperatures and of Ti concentrations of up to nominally 75%. We show a significant mechanical-loss reduction for the mixture with the highest Ti cation content, which crystallized after heat treatment at 500°C. The resulting loss is much lower than that of pure TiO2 or that of Ta2O5 after crystallization, making further studies highly interesting, in particular investigations of scattering which may pose a major drawback for optical applications. Published by the American Physical Society 2025

Diamond-like carbon thin films have emerged as durable, chemically stable optical coatings for many optical and optoelectronics applications due to their hardness, chemical inertness, and optical transparency. This paper presents a novel high-energy electron cyclotron resonance ion beam sputter deposition technique to fabricate pure diamond-like carbon coatings at room temperature. The chemical composition of the deposited coatings including ratios of sp2/sp3 bonding in the thin films were determined by X-ray photoelectron spectroscopy. Results indicate that the sp3 percentage ranges from 45% - 85%. The transmission and reflectance spectra of the coatings were measured from UV to IR ({\lambda}= 185 to 2500 nm) by utilizing a spectrophotometer. The measured spectra were analysed by the Tauc method to determine the optical band gap and Urbach energy and an optical fitting software, which utilizes the model modified by OJL, to extract the refractive index and extinction coefficient. By varying the ion energy, the optical properties were found to be n = 2.30 - 2.51, band gap energy = 0.4 - 0.68 eV, and the Urbach energy = 0.33 - 0.49 eV. This study provides a flexible method for tuning the structural, optical, and electronic properties of diamond-like carbon coatings by controlling the ion energy during deposition.

We present Fermi Gamma-ray Burst Monitor (Fermi-GBM) and Swift Burst Alert Telescope (Swift-BAT) searches for gamma-ray/X-ray counterparts to gravitational wave (GW) candidate events identified during the third observing run of the Advanced LIGO and Advanced Virgo detectors. Using Fermi-GBM on-board triggers and sub-threshold gamma-ray burst (GRB) candidates found in the Fermi-GBM ground analyses, the Targeted Search and the Untargeted Search, we investigate whether there are any coincident GRBs associated with the GWs. We also search the Swift-BAT rate data around the GW times to determine whether a GRB counterpart is present. No counterparts are found. Using both the Fermi-GBM Targeted Search and the Swift-BAT search, we calculate flux upper limits and present joint upper limits on the gamma-ray luminosity of each GW. Given these limits, we constrain theoretical models for the emission of gamma-rays from binary black hole mergers.

The mirror suspensions in gravitational wave detectors demand low mechanical loss jointing to ensure good enough detector performance and to enable the detection of gravitational waves. Hydroxide catalysis bonds have been used in the fused silica suspensions of the GEO600, Advanced LIGO, and Advanced Virgo detectors. Future detectors may use cryogenic cooling of the mirror suspensions and this leads to a potential change of mirror material and suspension design. Other bonding techniques that could replace or be used alongside hydroxide catalysis bonding are of interest. A design that incorporates repair scenarios is highly desirable. Indeed, the mirror suspensions in KAGRA, which is made from sapphire and operated at cryogenic temperatures, have used a combination of hydroxide catalysis bonding and gallium bonding. This Letter presents the first measurements of the mechanical loss of a gallium bond measured between 10 K and 295 K. It is shown that the loss, which decreases with temperature down to the level of (1.8±0.3)×10−4 at 10 K, is comparable to that of a hydroxide catalysis bond. Published by the American Physical Society 2024

Despite the growing number of confident binary black hole coalescences observed through gravitational waves so far, the astrophysical origin of these binaries remains uncertain. Orbital eccentricity is one of the clearest tracers of binary formation channels. Identifying binary eccentricity, however, remains challenging due to the limited availability of gravitational waveforms that include effects of eccentricity. Here, we present observational results for a waveform-independent search sensitive to eccentric black hole coalescences, covering the third observing run (O3) of the LIGO and Virgo detectors. We identified no new high-significance candidates beyond those that were already identified with searches focusing on quasi-circular binaries. We determine the sensitivity of our search to high-mass (total mass $M>70$ $M_\odot$) binaries covering eccentricities up to 0.3 at 15 Hz orbital frequency, and use this to compare model predictions to search results. Assuming all detections are indeed quasi-circular, for our fiducial population model, we place an upper limit for the merger rate density of high-mass binaries with eccentricities $0 < e \leq 0.3$ at $0.33$ Gpc$^{-3}$ yr$^{-1}$ at 90\% confidence level.

One of the main noise sources in current gravitational-wave detectors is the thermal noise of the high-reflectivity coatings on the main interferometer optics. Coating thermal noise is dominated by the mechanical loss of the high-refractive index material within the coating stacks, Ta 2 O 5 mixed with TiO 2 . For upgrades to room-temperature detectors, a mixture of GeO 2 and TiO 2 is an interesting alternative candidate coating material. While the rather low refractive index of GeO 2 increases with increasing TiO 2 content, a higher TiO 2 content results in a lower threshold temperature before heat treatment leads to crystallisation, and potentially to a degradation of optical properties. For future cryogenic detectors, on the other hand, a higher TiO 2 content is beneficial as the TiO 2 suppresses the low-temperature mechanical loss peak of GeO 2 . In this paper, we present the optical properties of coatings—produced by plasma-assisted ion-beam evaporation—with high TiO 2 content at 1550 nm, a laser wavelength considered for cryogenic gravitational-wave detectors, as a function of heat-treatment temperature. For comparison, the absorption of pure GeO 2 was also measured. Furthermore, results at the currently-used wavelength of 1064 nm are presented.

Silicon nitride thin films were deposited at room temperature employing a custom ion beam deposition (IBD) system. The stoichiometry of these films was tuned by controlling the nitrogen gas flow through the ion source and a process gas ring. A correlation is established between the process parameters, such as ion beam voltage and ion current, and the optical and mechanical properties of the films based on post-deposition heat treatment. The results show that with increasing heat treatment temperature, the mechanical loss of these materials as well as their optical absorption decreases producing films with an extinction coefficient as low as k = 6.2 ( +/- 0.5 ) x 10 - 7 at 1064 nm for samples annealed at 900 circle C. This presents the lowest value for IBD SiN x within the context of gravitational wave detector applications. The mechanical loss of the films was measured to be phi = 2.1 ( +/- 0.6 ) x 10 - 4 once annealed post deposition to 900 circle C.

The magnetar SGR 1935+2154 is the only known Galactic source of fast radio bursts (FRBs). FRBs from SGR 1935+2154 were first detected by the Canadian Hydrogen Intensity Mapping Experiment (CHIME)/FRB and the Survey for Transient Astronomical Radio Emission 2 in 2020 April, after the conclusion of the LIGO, Virgo, and KAGRA Collaborations' O3 observing run. Here, we analyze four periods of gravitational wave (GW) data from the GEO600 detector coincident with four periods of FRB activity detected by CHIME/FRB, as well as X-ray glitches and X-ray bursts detected by NICER and NuSTAR close to the time of one of the FRBs. We do not detect any significant GW emission from any of the events. Instead, using a short-duration GW search (for bursts <= 1 s) we derive 50% (90%) upper limits of 10(48) (10(49)) erg for GWs at 300 Hz and 10(49) (10(50)) erg at 2 kHz, and constrain the GW-to-radio energy ratio to <= 10(14)-10(16). We also derive upper limits from a long-duration search for bursts with durations between 1 and 10 s. These represent the strictest upper limits on concurrent GW emission from FRBs.

We report the observation of a coalescing compact binary with component masses 2.5-4.5 M-circle dot and 1.2-2.0 M-circle dot (all measurements quoted at the 90% credible level). The gravitational-wave signal GW230529_181500 was observed during the fourth observing run of the LIGO-Virgo-KAGRA detector network on 2023 May 29 by the LIGO Livingston observatory. The primary component of the source has a mass less than 5 M-circle dot at 99% credibility. We cannot definitively determine from gravitational-wave data alone whether either component of the source is a neutron star or a black hole. However, given existing estimates of the maximum neutron star mass, we find the most probable interpretation of the source to be the coalescence of a neutron star with a black hole that has a mass between the most massive neutron stars and the least massive black holes observed in the Galaxy. We provisionally estimate a merger rate density of 55(-47)(+127) Gpc-3yr(-1) for compact binary coalescences with properties similar to the source of GW230529_181500; assuming that the source is a neutron star-black hole merger, GW230529_181500-like sources may make up the majority of neutron star-black hole coalescences. The discovery of this system implies an increase in the expected rate of neutron star-black hole mergers with electromagnetic counterparts and provides further evidence for compact objects existing within the purported lower mass gap.

A novel high-energy electron cyclotron resonance (ECR) ion beam deposition (IBD) technique was used to fabricate DLC films at different ion beam energies. The ratios of sp2/sp3 bonding in the DLC coatings were determined by Raman spectroscopy and XPS, with the confirmation of being hydrogen-free due to the lack of photoluminescence (PL) background in the Raman spectra. The results indicate that the sp3 percentage ranges from 45 fabricated DLC films in this study. Monte-Carlo based SRIM simulation was used to extract the energy and angular distribution of the sputtered particles from the carbon target and correlate it to the highest sp3 fraction in the manufactured ECR-IBD DLCs. This study demonstrates a method of depositing DLC thin films under ambient conditions (room temperature with no post-annealing or additional bias voltage applied) which produces high-sp3 coatings (higher than those traditionally reported for other sputtering methods) suitable for applications where high quality DLC coatings are required.

Magnetars are neutron stars with exceptionally strong dipole magnetic fields which are observed to display a range of x-ray flaring behavior, but the flaring mechanism is not well understood. The third observing run of Advanced LIGO and Virgo extended from April 1, 2019 to March 27, 2020, and contained x-ray flares from known magnetar SGR 1935+2154, as well as the newly-discovered magnetar, Swift J1818-1607. We search for gravitational waves coincident with these magnetar flares with minimally modeled, coherent searches which specifically target both short-duration gravitational waves produced by excited f-modes in the magnetar's core, as well as long-duration gravitational waves motivated by the Quasi-Periodic Oscillations observed in the tails of giant flares. In this paper, we report on the methods and sensitivity estimates of these searches, and the astrophysical implications.

Among the various candidates for dark matter (DM), ultralight vector DM can be probed by laser interferometric gravitational wave detectors through the measurement of oscillating length changes in the arm cavities. In this context, KAGRA has a unique feature due to differing compositions of its mirrors, enhancing the signal of vector DM in the length change in the auxiliary channels. Here we present the result of a search for $U(1)_{B-L}$ gauge boson DM using the KAGRA data from auxiliary length channels during the first joint observation run together with GEO600. By applying our search pipeline, which takes into account the stochastic nature of ultralight DM, upper bounds on the coupling strength between the $U(1)_{B-L}$ gauge boson and ordinary matter are obtained for a range of DM masses. While our constraints are less stringent than those derived from previous experiments, this study demonstrates the applicability of our method to the lower-mass vector DM search, which is made difficult in this measurement by the short observation time compared to the auto-correlation time scale of DM.

Gravitational lensing by massive objects along the line of sight to the source causes distortions to gravitational wave (GW) signals; such distortions may reveal information about fundamental physics, cosmology, and astrophysics. In this work, we have extended the search for lensing signatures to all binary black hole events from the third observing run of the LIGO-Virgo network. We search for repeated signals from strong lensing by (1) performing targeted searches for subthreshold signals, (2) calculating the degree of overlap among the intrinsic parameters and sky location of pairs of signals, (3) comparing the similarities of the spectrograms among pairs of signals, and (4) performing dual-signal Bayesian analysis that takes into account selection effects and astrophysical knowledge. We also search for distortions to the gravitational waveform caused by (1) frequency-independent phase shifts in strongly lensed images, and (2) frequency-dependent modulation of the amplitude and phase due to point masses. None of these searches yields significant evidence for lensing. Finally, we use the nondetection of GW lensing to constrain the lensing rate based on the latest merger-rate estimates and the fraction of dark matter composed of compact objects.

The second Gravitational-Wave Transient Catalog reported on 39 compact binary coalescences observed by the Advanced LIGO and Advanced Virgo detectors between 1 April 2019 15:00 UTC and 1 October 2019 15:00 UTC. We present GWTC-2.1, which reports on a deeper list of candidate events observed over the same period. We analyze the final version of the strain data over this period with improved calibration and better subtraction of excess noise, which has been publicly released. We employ three matched-filter search pipelines for candidate identification, and estimate the astrophysical probability for each candidate event. While GWTC-2 used a false alarm rate threshold of 2 per year, we include in GWTC-2.1, 1201 candidates that pass a false alarm rate threshold of 2 per day. We calculate the source properties of a subset of 44 high-significance candidates that have an astrophysical probability greater than 0.5. Of these candidates, 36 have been reported in GWTC-2. If the 8 additional high-significance candidates presented here are astrophysical, the mass range of events that are unambiguously identified as binary black holes (both objects $\geq 3M_\odot$) is increased compared to GWTC-2, with total masses from $\sim 14 M_\odot$ for GW190924_021846 to $\sim 182 M_\odot$ for GW190426_190642. The primary components of two new candidate events (GW190403_051519 and GW190426_190642) fall in the mass gap predicted by pair instability supernova theory. We also expand the population of binaries with significantly asymmetric mass ratios reported in GWTC-2 by an additional two events (the mass ratio is less than $0.65$ and $0.44$ at $90\%$ probability for GW190403_051519 and GW190917_114630 respectively), and find that 2 of the 8 new events have effective inspiral spins $\chi_\mathrm{eff} > 0$ (at $90\%$ credibility), while no binary is consistent with $\chi_\mathrm{eff} < 0$ at the same significance.