The development of durable efficient water repellent textiles without perfluoroalkyl and polyfluoroalkyl substances (PFAS) is critical for sustainability. However, alternative alkyl-based coating solutions are generally less efficient. Here, we show how the hydrophobicity of a typical biobased fluorine-free coating (Lamoral A5) can be boosted by the multiscale design of the topographic spectrum of polyester fabrics from the submicrometer to the millimeter range. Using nanogravure printing, we fabricated mechanically robust textiles exhibiting nanopillared arrays superimposed on the intrinsic fabric roughness arising from weave pattern and fibers-in-yarn packing, thereby mimicking natural hierarchical superhydrophobic surfaces. We analyze the roughness spectrum of these surfaces by "Wenzel spectroscopy," a new mathematical analysis combining images obtained at different resolutions and sizes allowing us to identify the contribution of different spatial ranges to the total Wenzel roughness of a surface. Thereby, we demonstrate how the submicrometer components of the roughness spectrum are critical for improving the water repellency of smoother fabrics. Although initially smooth fabrics are in the impregnated Wenzel regime, nanostructuring moves these fabrics toward or into the Cassie-Baxter regime in which air pockets are trapped below water droplets; accordingly, the contact angle increases by 5 to 10°, and the pinning parameter decreases until the Cassie-Baxter state is attained. Initially rougher fabrics, which are already in the Cassie-Baxter regime, are less affected. Our approach demonstrates an inherently scalable, environmentally responsible route to advanced functional textiles, combining nanostructuring and sustainable chemistry for outdoor and protective applications.
The purpose of this study is to apply and evaluate the Circular Footprint Formula (CFF), as part of the European Commission’s Product Environmental Footprint (PEF) framework, through an assessment of the environmental performance of thermomechanically recycled mono-material polyester carpets. Unlike multi-material carpets that are often incinerated at the end of their life, mono-material designs facilitate fiber-to-fiber recycling - a key priority for the European Union in reducing the large environmental burdens of the textile industry. The environmental assessment is structured around the CFF as recycling allocation method. In addition, a comparison is made with the 100:0 approach as a benchmark, also known as the cut-off or recycled content method, as recommended in the Environmental Product Declaration (EPD). Different potential values for two main parameters within the CFF were considered: factor A, reflecting the market dynamics of supply and demand for recycled materials, and factor B, distributing the burdens and credits associated with energy recovery. Both allocation methods were applied to the carpet case study, which considered three possible scenarios: recycling of the monomaterial carpet (MMC), incineration of the conventional multi-material carpet, and incineration of the MMC. The impact assessment follows the indicators defined by PEF framework. The findings indicate that recycling of MMCs generally results in lower environmental impacts than direct incineration across most impact categories, thereby aligning with the principles of a circular economy. Importantly, incinerating MMCs without prior recycling can lead to more severe environmental burdens than the incineration of conventional carpets, as demonstrated through a comparative product system-level analysis. The results also suggest that factor A has a significantly greater influence on environmental outcomes at individual product level than factor B, with changes in A, for example, leading to impact differences of up to 30
Infectious wounds pose significant challenges, especially with the growing issue of antibiotic resistance, which makes traditional antibiotic treatment less effective. For this reason, recent research has been seeking alternative types of treatment using probiotics. This research evaluate to was to fabricate and assess electrospun hyaluronic acid/polyvinyl alcohol (PVA) fibers incorporating Micrococcus luteus for wound management. The PVA/hyaluronic acid fibers were fabricated with electrospinning and crosslinked by dry heat treatment. Fiber morphology before and after crosslinking was examined using scanning electron microscopy (SEM). Further tests, such as Fourier-transform infrared spectroscopy (FTIR) and mechanical strength analysis, were conducted on the optimized crosslinked sample. Water vapor transmission rate (WVTR) was also measured to evaluate suitability for wound dressing applications. Micrococcus luteus in polyethylene oxide (PEO) was electrosprayed on the fibrous mat, and probiotic viability was tracked for 28 days. Antibacterial activity against Staphylococcus aureus and Pseudomonas aeruginosa were evaluated. Biocompatibility and wound healing potential were evaluated through MTT and scratch closure tests at 0, 4, and 24 h. The fibers produced were 202 +/- 23 nm, with a decrease in diameter following crosslinking. FTIR verified the esterification of the polymers. Mechanical testing indicated appropriate ability for wound application, while WVTR results demonstrated the material's capability to maintain a moist environment. The probiotic remained viable and effectively inhibited both pathogens. MTT results showed over 80 % cell viability, demonstrating high biocompatibility. The scratch assay also demonstrated full wound closure within 24 h, confirming the wound dressing's strong healing potential.
Fused Filament Fabrication (FFF) 3D printing of electrically conductive paths holds promise for implementing smart electronic functionalities on textiles. The ease of design modifications, a high degree of design freedom and the structural functionality of 3D printing make it an attractive technology for the rapidly evolving field of smart textiles which is still being explored for its full potential regarding functionalities. In electronic textiles, the conductivity of conductive tracks needs to remain stable under conditions such as repeated stretching, abrasion or washing. We show the behaviour of conductive materials printed using FFF under repeated strain with a focus on the functional additives used to achieve conductivity. Different carbon based additives, such as carbon black (CB) materials optimized for conductivity and multi-walled carbon nanotubes (MWCNT), as well as short metal fibres are investigated for this purpose. The need for detailed investigation of electrical conductivity after each production stage and during use is explained and effects of printing and repeated strain on materials are discussed. Durability against abrasion and washing under different conditions are tested.