The Korea Research Institute of Standards and Science (KRISS) is the national measurement standards laboratory for the Republic of Korea. It is a government-funded institute responsible for providing national measurement standards and advancing measurement technologies. KRISS is also an active member of the General Conference on Weights and Measures (CGPM).
Understanding the long-term thermal stability of metal-organic precursors is critical for maintaining consistent and reliable atomic layer deposition (ALD) performance. Conventional evaluations, such as thermogravimetric analysis (TGA) and bulk long-term thermal stability tests in sealed containers, do not reproduce the vacuum exposure and pressure fluctuations encountered under practical ALD process environments. In this work, we developed a vacuum-based long-term stability evaluation platform that reproduces process-relevant pressure cycling while enabling extended thermal treatment and periodic, atmosphere-free sampling of liquid precursors. Using tetrakis(ethylmethylamino)hafnium (TEMAHf) as a model precursor, we compare non-pumping, 6-h cyclic pumping, and 1-h cyclic pumping environments and track degradation using colorimetry, TGA residual mass, viscosity, and vapor pressure. More frequent pressure cycling accelerates degradation, evidenced by stronger color changes, increased non-volatile residue accumulation, higher viscosity, and reduced vapor pressure. These results indicate that non-vacuum, non-cycling tests can underestimate process-relevant long-term degradation and highlight the need for vacuum- and pressure cycling-based protocols to screen precursor stability and guide precursor and process optimization in ALD.
Two-dimensional (2D) semiconductors enable atomically thin channels and attractive electrostatics, but practical scaling increasingly hinges on gate-dielectric integration rather than channel performance. A key challenge is forming high-quality dielectrics on chemically inert, dangling-bond-free 2D surfaces while pushing equivalent oxide thickness to the sub-nanometer regime without excessive leakage, traps, or electrical breakdown. This review addresses the materials and process physics that govern dielectric formation in 2D devices, with an emphasis on atomic layer deposition nucleation, surface pretreatment and functionalization, and the use of seed and buffer layers for conformal high-κ oxides. The roles of layered insulators, such as hexagonal boron nitride, are discussed in terms of interface quality, electrostatic scaling limits, and transport limitations. The impact of dielectrics and processing on leakage mechanisms, defect generation, device-to-device variability, and reliability metrics, including time-dependent dielectric breakdown, bias-temperature instability, hysteresis, and threshold-voltage drift, is examined. Finally, we highlight van der Waals dry integration and dielectric transfer approaches that reduce process-induced damage and support wafer-scale uniformity, as well as opportunities for mixed-dimensional and 3D stacked architectures across logic, memory, and emerging functional systems.
The continued scaling of semiconductor devices toward high-aspect-ratio architectures necessitates increasingly aggressive plasma etching conditions, which in turn accelerate the degradation of plasma-facing chamber components. Consequently, there is an urgent need to develop alternative materials that surpass conventional candidates, such as Al2O3 and YAG, by offering both cost-effectiveness and superior erosion resistance. In this study, polycrystalline MgO ceramics were fabricated via hot pressing with the incorporation of Al2O3, Y2O3, and SiO2 additives. The effects of additive composition and sintering temperature on the resulting microstructure and plasma etching resistance were systematically investigated. The synthesized MgO ceramics exhibited a dense, fine-grained microstructure and achieved an etching rate significantly lower (12–33
An infrared absorption-based flow sensor has been created to precisely measure the output from dispensers utilized in electronic packaging. The sensor works by heating a local spot on the epoxy-supplying tube using a laser, which thermally tags the epoxy. The velocity and discharge time of the epoxy are then measured using pairs of light-emitting diodes and photodetectors to determine the discharge quantity. The range of the measured dispenser discharge volume was from 2.87 mg to 21.69 mg, measured within the range used in actual semiconductor processes. The maximum deviation from the scale measurement was 2.6
Sound source localization (SSL) has gained widespread attention due to its critical role in various applications. As a representative SSL algorithm, the time difference of arrival (TDOA) method estimates the direction of arrival (DOA) of the sound source by calculating the cross-correlation (CC) of measured signals from multiple microphones. For TDOA-based DOA estimation, noisy environments and finite sampling rates complicate precise DOA measurements, while inaccuracies in microphone array (MA) configurations further challenge SSL accuracy. To address these challenges, we propose the microphone graph network (MicGraphNet), a novel deep learning framework leveraging graph neural networks (GNNs) for TDOA-based SSL. MicGraphNet takes advantage of the inductive bias between microphone-array configurations and CC features, enabling efficient learning that compensates for noise-and reverberation-induced errors and thereby improves DOA accuracy. MicGraphNet also directly regresses continuous TDOAs rather than relying on grid-based CC peaks, which mitigates quantization errors and enhances precision. Finally, the model incorporates a position-uncertainty injector, enhancing robustness to practical sensor placement inaccuracies. Experimental validations conducted in free-field, anechoic chamber, reverberant rooms, as well as conversational speech scenarios, demonstrate that MicGraphNet consistently improves DOA accuracy across multiple tetrahedral sub-array configurations. In particular, average DOA error reductions of approximately 14 degrees, 3 degrees, 8 degrees, and 4 degrees were obtained in these respective environments, confirming the model's effectiveness in real-world applications.