
In the present study, we experimentally investigate the dynamics of a single air bubble rising against an inclined wall, with focus on the influence of surface wettability under high-Reynolds- and Weber-number conditions. Experiments were conducted in a quiescent water tank using three wall materials (glass, PMMA, and PTFE), with inclination angles ranging from 15^∘ to 75^∘ . High-speed shadowgraphy confirmed that the bubble motion generally changes from sliding behavior to periodic bouncing with increasing inclination angle, while the detailed regime classification varies depending on the surface wettability. Across the critical angle of α =45^∘ , the surface wettability mainly affected the post-impact response, particularly the contact time. To elucidate the underlying mechanism, two-phase particle image velocimetry was performed around the transitional inclination angle, revealing that the wettability alters the spatial distribution and persistence of vorticity structures near the bubble and wall. These findings are further supported by the analysis on transfer among kinetic and surface energy, and viscous dissipation rate distribution. In summary, the present results show that the wall inclination primarily determines the bubble motion, while the surface wettability modifies the deformation after impact as well as the evolution and dissipation of wake vortices.
A hybrid algorithm combining particle image velocimetry (PIV) and Navier–Stokes (N–S) equations using a pressure correction scheme (PCS) based on the numerical projection method, named PIV–PCS, has been proposed to optimize velocity fields (Wang et al. 2018, Exp. Fluids, 59:149). In the present work, we extend the PIV–PCS method to calculate pressure fields with solid boundaries, a challenge that requires addressing the pressure boundary conditions (BCs). Three strategies are evaluated: BC1 is a commonly used Neumann condition for the pressure gradient calculated from the measured velocity field; BC2 involves estimation of the pressure gradient on the surface of an object according to the nonslip boundary condition; and BC3 is based on the assumption of the zero normal pressure gradient on the surface, as in computational fluid dynamics. According to the numerical assessment using direct numerical simulation data, BC2 is recommended for optimizing the velocity field within the PIV–PCS algorithm, whereas BC1 is more suitable for solving the PIV–PCS-based pressure from the optimized velocity fields. Numerical cases of a two-dimensional (2D) flow around a circular cylinder and a three-dimensional (3D) separated flow around an airfoil both demonstrate that the PIV–PCS-based pressure reconstruction method reduces pressure error by approximately 83
Multi-element wings are increasingly adopted across a range of applications due to the possibility of actively controlling the aerodynamic forces under varying operating conditions. Effective control, however, requires a detailed understanding of their stall and hysteresis behaviour. The present study investigates stall and hysteresis experimentally on a slotted two-element wing with a rectangular planform, designed for wind-assisted ship propulsion. Aerodynamic load measurements are combined with particle image velocimetry at multiple spanwise locations. The measurements reveal two abrupt stall stages, each accompanied by hysteresis. The first corresponds to a transition from the attached high-lift state to a partially separated flow state with reduced lift but substantial remaining flow attachment, giving rise to a minor hysteresis loop. The second corresponds to the transition to a fully stalled state associated with a large hysteresis loop. These transitions coincide with rapid flow reorganisations involving the slot jet, the element wakes, and separated regions, whereas otherwise the flow evolves smoothly with inflow angle. While the partially separated flow state exhibits pronounced spanwise variation, the fully stalled state is comparatively uniform. The observed behaviour is robust across Reynolds numbers between 0.5× 10^6 and 1.1× 10^6 and across measurements conducted in two wind-tunnel facilities. These findings establish a direct link between multi-stage stall, hysteresis, and the underlying flow structures, supporting the development of physics-based control strategies for wingsails and other actively controlled multi-element wings.
Event-based cameras offer new opportunities for particle tracking in fluid mechanics by providing asynchronous, sparse measurements with high temporal resolution and no fixed acquisition frequency. Processing such data requires algorithms capable of fully exploiting these distinctive features. A natural first approach to perform particle tracking on event-based data is to apply a clustering algorithm, in particular DBSCAN, as it does not require specifying the number of clusters a priori. In this paper, we show, using a simplified synthetic two-particle system, that this classical algorithm is severely limited in terms of the accessible velocity range v_max/v_min . To address this limitation, and to take advantage of the absence of a fixed acquisition frequency in event-based cameras, we propose a new two-dimensional, two-component (2D2C) particle tracking algorithm based on clustering. The method relies on a recursive application of DBSCAN with multiple temporal normalizations, retaining only clusters that satisfy a set of validation criteria. A key feature of the proposed algorithm is that it does not assume any characteristic time scale or typical velocity. The algorithm is evaluated on realistic synthetic datasets generated from numerical simulations of turbulent flows, and the influence of key parameters is systematically investigated. Particular attention is given to the definition of evaluation metrics adapted to clusters of events for particle tracking. Finally, the proposed algorithm is applied to experimental data acquired in a turbulent flow generated by a von Kármán apparatus, demonstrating its ability to extract particle trajectories from real event-based measurements.
Wall compliance in soft conduits can trigger flow instability at Reynolds numbers far below the classical rigid-pipe threshold, yet the near-wall spatial structure of this transition has not previously been measured. Here we address this gap using high-speed particle tracking velocimetry in PDMS microtubes with systematically varied wall compliance ( G' = 14 – 392 kPa ). The principal finding is that the onset of compliance-induced transition is accompanied by a pronounced near-wall localization of coupled velocity fluctuations at r/R ≈ 0.7 –0.9, which is absent in the rigid control tube and intensifies with wall softness. Three alternative explanations, namely junction geometry, tracer-related measurement bias, and deformation-induced error in the Reynolds number definition, are examined and found not to account for this localization, which is therefore interpreted as a spatial signature consistent with an elastic–fluid instability originating at the compliant boundary. We further introduce two fabrication-consistent corrections, post-solvent treatment measurement of the shear modulus, and optical measurement of the resting tube radius, and show that these quantify compliance-dependent biases in Re and Σ that are present in this class of experiments. A secondary, exploratory scaling analysis based on only four independent compliance levels yields Re_t ∝Σ ^0.48 (BCa 95 Σ ^1/2 and Σ ^5/8 scalings. A study-level analysis of the combined experimental literature reveals substantial inter-study heterogeneity in the fitted exponent ( n = 0.41 –1.24; I^2 = 96% ), indicating that a universal Re_t ∝Σ ^n power law is not supported by the existing database and that transition thresholds extrapolated from any single assumed scaling should be treated with caution.