
The derivatives of hybrid perovskites, (CH3)3SPbI3-xBrx and (CH3)3SPbI3-xClx, where x = 0, 1, 2, and 3 have been synthesized. Aided by Density Functional Theory (DFT) computations employing B3LYP and B3PW91 methods, the molecular geometry was initially optimized for the isolated trimethyl sulphonium ion, [CH3)3S]+, up to 6-311++G(d,p) basis. However, combined basis sets employing both 6-31G(d) and 6-311 + G(d) was combined with LANL2DZ, in case of anions that contain(s) "lead and iodine heavy atoms". The optimized structures at equilibria for [CH3)3S]+, [PbCl3]-, [PbBr3]-, [PbI3]- ions were restricted to C3v point group, while the anions, [PbI2Cl] -, [PbI2Br]-, [PbICl2]-, [PbIBr2]- obey Cs symmetry followed by frequency calculations at the same basis set. Otherwise, combined basis set were used for ions containing Pb, Cl and Br. The already reported Raman (10-3,500 cm-1) and infrared (200-4,000 cm-1) spectra of perovskite samples in the solid phase were analyzed based on estimated frequencies, normal coordinate analysis (NCA) and potential energy distributions (PEDs). All observed bands were correlated to the appropriate normal modes of vibration. The computed structural parameters (Ps) were in good agreement with those reported from X-ray single crystal. Minor deviations in the X-Pb-X bond angles were observed, indicating that the unit has been isolated as a distorted face-sharing [PbI6] polyhedral chain extending one-dimensionally along the c-axis, rather than as a monomeric molecule. Aided by potential surface scan, methyl barriers to internal rotations of 674-810 cm-1 (1.93-2.32 kcal/mol) and 652-790 cm-1 (1.86-2.26 kcal/mol) were estimated from B3LYP and B3PW91 at 6-311++G(d,p) basis set, respectively. All results presented herein are compared with similar molecules whenever appropriate.
Indoor photovoltaics (IPV) are emerging as a key enabling technology for self-powered sensors and portable electronics, yet the development of high-performance absorbers optimized for low-intensity illumination remain limited. In this work, we investigate the suitability of antimony sulfide (Sb2S3) for indoor solar energy harvesting using comprehensive device-level simulations performed in SCAPS-1D. The influence of absorber layer thickness and illumination source (warm LED, cool LED, halogen, xenon, fluorescent, incandescent, and AM1.5G sunlight) was systematically analyzed to identify performance-limiting factors and optimal design parameters. Our results show that Sb2S3 exhibits strong potential for indoor environments due to its favorable bandgap (1.7-1.8 eV) and high absorption coefficient, enabling efficient carrier generation under artificial lighting. The simulations shows that in the thickness range 200-2000 nm, an absorber thickness of 400-600 nm yields the highest indoor power conversion efficiency, reaching similar to 37.4 % under warm LED illumination, while under AM1.5G conditions the optimal thickness is similar to 500 nm with a maximum efficiency of 22.2 %, respectively. The strong sensitivity of efficiency to illumination spectrum underscores the importance of spectral matching in IPV device design. This study establishes the thickness-dependent performance limits of Sb2S3-based solar cells under realistic indoor lighting and highlights their promise as cost-effective absorbers for next-generation low-light photovoltaic applications.
The single crystal structure of Sodium Suphanilate Dihydrate (SSDH) features infinitely connected cationic metal-organic frameworks (MOFs) of Sodium and Oxygen atoms blended with strong and moderate hydrogen bonding interactions. The crystal packing shows alternate hydrophilic and hydrophobic regions along the c-axis of the unit cell at z = 0, & half; and 1 and at z = & frac14; and & frac34;, respectively. The powder XRD pattern confirms the crystalline phase of the grown crystal. The molecular structure of SSDH was quantum chemically optimized by DFT method. The various functional group species of the compound was investigated by Fourier Transformed Infra-Red and Raman spectroscopic techniques and compared with quantum chemically computed counterparts. The calculated Frontier Molecular Orbital energies reveal the charge transfer characteristic of SSDH along with the chemical hardness, electro-negativity and electrophilicity index which are key to make optoelectronic devices. The atomic charge distribution of the molecular assembly was analyzed by Mulliken Charge analysis method. The UV-Visible absorbance spectra exhibit a characteristic peak of absorbance at lambda = 248 nm. The nonlinear optical parameters of the crystal such as absorption coefficient, susceptibilities and nonlinear refractive index were determined by the Z-scan technique.
Plant extracts offer diverse phytochemical stabilizers that may enhance the antimicrobial effectiveness of copper-based nanoparticles. In this study extracts from 21 different plant tissues were employed in this regard via hydrolysis reactions. Nicotiana rustica leaf extract emerged as a particularly effective stabilizer, increasing antimicrobial activity by 1.75 times against Staphylococcus aureus, although it did not influence antimicrobial activity against Escherichia coli. N. rustica extract reduced particle size from 379-2,125 nm to 5-35 nm and also decreased crystal size from 236 & Aring; to 84 & Aring;. The nanoparticles were identified as Cu(OH)2 crystals, and N. rustica extract had no effect on the crystal structure. FTIR spectroscopy revealed that aliphatic hydrocarbons, fatty acids, and phenolic compounds from N. rustica capped the surface of the nanoparticles. This capping changed the zeta potential from -40.4 +/- 1.6 mV to 16.2 +/- 0.6 mV, making it more suitable for antimicrobial purposes. Thus, N. rustica extract proves to be an innovative stabilizer that enhances both the physicochemical and antimicrobial properties of copper-based nanoparticles.