
Solid-solid phase transformation mechanisms need to be understood to establish suitable kinetic laws. Here, the β-Sn ↔ γ-Sn phase transformations are investigated at different strain rates at 300 K. On one side, single crystals have been statically compressed and characterized using in situ x-ray diffraction. Multiple transformation cycles were performed in diamond anvil cells to measure their conditions and the associated microstructures. (101)β∣∣(110)γ and $${[10\bar{1}]}_{\beta }| | {[1\bar{1}1]}_{\gamma }$$ orientation relationships (OR) between β-Sn and γ-Sn are observed in most cases, for both direct and reverse transformations. An atomic martensitic transformation mechanism, associated with self-accommodation, is proposed to account for these OR and variant selection. However, γ-Sn → β-Sn reversion also presents features that are consistent with recrystallization in β-Sn or a massive transformation. On the other side, time-resolved (22 μ s scale) dynamic diamond anvil cell experiments have been carried out. They show that while β-Sn → γ-Sn transformation is fast (Pβ→γ=10.9 ± 0.2, insensitive to strain rate), reversion pressure Pγ→β varies with strain rate, from 9.4 ± 0.8 GPa to 6.35 ± 0.7 GPa. Moreover, timescales of β-Sn formation and subsequent recrystallization/growth in this phase can be distinguished. A different kinetic description needs to be used for direct and reverse transitions. Solid-solid phase transformation mechanisms need to be understood to establish suitable kinetic laws. Here, the beta-phase Sn ↔ gamma-phase Sn phase transformation is investigated at different strain rates at 300 K.
The uranium-hydrogen system has been predicted to form numerous polyhydride compounds, exhibiting diverse physical properties. However, experiments report starkly conflicting results regarding synthesis pressures, stoichiometries, and stability, leaving their fundamental properties and even their existence uncertain. Through a series of laser-heated diamond anvil cell experiments, we systematically investigate the high-pressure phase diagram of the uranium-hydrogen system up to 99(3) GPa using synchrotron powder X-ray diffraction. Compression and laser heating of β -UH 3 at pressures of 41(1) and 91(3) GPa result in the formation of hcp -UH 7 and fcc -UH 8 , respectively. Upon decompression of hcp -UH 7 below 27(1) GPa, we observe decomposition into hcp -UH 5 , which subsequently further dehydrogenates to U 4 H 15 below 12(1) GPa. The U 4 H 15 compound, analogous to the well-known Th 4 H 15 , is recoverable to ambient pressure and temperature, and slowly oxidizes over the timescale of hours. Whilst all compounds are metallic, electrical resistance measurements demonstrate an absence of superconductivity upon cooling to 3 K in U 4 H 15 , hcp -UH 5 , and hcp -UH 7 , and to 7 K in fcc -UH 8 .
Machine learning is transforming materials discovery, yet its impact on multi-objective optimisation remains constrained by the structure and quality of input data. Despite the growing use of advanced predictive models, most studies rely on single-property datasets developed for specific purposes and not designed for cross-domain integration. Fragmented descriptors, inconsistent metadata, and missing values prevent models from learning relationships across properties and material classes, limiting effective optimisation. This perspective focuses on data-driven materials informatics (with an emphasis on metal alloys) and contends that progress in multi-objective materials design relies on integrated, reliable data infrastructures that enable cross-domain learning and support practical optimisation. We demonstrate this by unifying fragmented mechanical and corrosion databases into a single resource for multi-objective design of multi-principal element alloys. Machine learning promises accelerated materials discovery, but fragmented and inconsistent datasets continue to limit effective multi-objective optimisation across materials systems. In this Perspective, the authors argue that integrated data infrastructures are essential for cross-domain learning and demonstrate this by unifying mechanical and corrosion databases to enable the multi-objective design of multi-principal element alloys.
The Mg2+ and Ni2+ ions at the Li site (A-site) in Ni-rich NMC layered cathode materials improve their cycling stability by reducing intragranular cracking. These cations act as “rivets” due to their ability to suppress gliding of the close-packed layers and associated mechanically-destructive phase transitions. In the present study the impact of the Mg2+ and Ni2+ ions on the mechanical properties of the single-crystal Mg-doped NMC811 materials has been investigated quantitatively with in situ micropillar compression, nanoindentation and pillar splitting in a scanning electron microscope. Here we show that the increase in cumulative occupancy of the “rivet” cations NiA and MgA at the A-site in the layered R$$\bar{3}$$m structure results in an increase of the critical resolved shear stress of the basal {0001} < 11$$\bar{2}$$0> slip system activation, hardness, fracture toughness K1c and Young’s modulus. Density functional theory calculations demonstrate that the Ni/Mg for Li substitution contributes synergistically to the enhancement of mechanical properties in NMC811. Mg²⁺ and Ni²⁺ ions at Li sites enhance Ni-rich NMC stability by acting as structural rivets that suppress layer gliding and cracking. Here, the authors show that Mg²⁺ and Ni²⁺ at Li sites synergistically enhance the mechanical strength and toughness of single-crystal NMC811.
Metal–organic frameworks (MOFs) are functional nanoporous materials with high surface areas exhibiting great promise for diverse device applications. However, their beam-sensitive structure renders them highly susceptible to electron and ion beam damage, leading to decomposition during etching and hindering fine patterning. In this study, we developed a simple method for room-temperature dry etching of this fragile class of materials. By infiltrating MOFs with ionic liquids, their mechanical stability is greatly improved, and the damage from electron and ion beams is reduced, achieving harmless ion beam etching. Using this method, fine patterning of MOFs with sub-100-nm precision was successfully accomplished at room temperature. The influence of ionic liquid type on the dry etching properties of MOFs was studied, and possible damage mechanisms were suggested, involving reduction of Cu2+ to Cu+ and cleavage of the Cu–O bond. Metal–organic frameworks are promising nanoporous materials, but their sensitivity to electron and ion beams limits fine patterning. Here, the authors developed a room-temperature dry-etching method for metal–organic frameworks by infiltrating them with ionic liquids, improving beam resistance and enabling sub-100 nm patterning while elucidating possible damage mechanisms.