
ABSTRACT The continuous capture process, with its benefits of enhanced productivity, resin utilization, and reduced footprint, has significantly saved costs. Due to the complexity of three‐column periodic counter‐current chromatography (3 C‐PCC), a represented 3‐column scale‐down model (SDM) based on conventional ÄKTA equipment is still absent for viral clearance (VC) validation. This paper established a novel tailored SDM for mimicking the flow path of 3 C‐PCC based on conventional ÄKTA equipment and then validated its viral clearance capability. Variability in input material attributes and different process phases were considered when performing viral clearance assessments in this study. Comparable LRVs were achieved across different harvest stage (including early, middle and late harvests) and process state (including start‐up, steady and close‐down states), thereby providing valuable insights for designing viral clearance validation of 3C‐PCC. Moreover, the virus distribution patterns and carryover of the ÄKTA pcc SDM were investigated and generally consistent with batch mode, and there was no detectable virus residue in any column of ÄKTA pcc SDM post sanitization. Overall, this study established a novel 3C‐PCC SDM based on conventional ÄKTA equipment and provided valuable data to support future design of 3C‐PCC viral clearance validation.
ABSTRACT Transient expression systems enable rapid and scalable production of plant‐made pharmaceuticals (PMPs). However, maximizing PMP productivity while optimizing electricity use on vertical farms remains challenging. Increasing planting density improves biomass per area but can reduce PMP content per biomass due to self‐shading. Supplemental lighting (sL) can mitigate shading but increases electricity use. Here, we study sL lighting strategies with reasonable electricity use under high‐density Nicotiana benthamiana cultivation (800 plants m –2 ) with hemagglutinin (HA, an influenza vaccine antigen) and an antibody. Gene transfer (GT) was conducted 35–36 days post‐sowing, followed by plant harvest 6–7 days later. Plants were categorized based on the timing of sL treatment: pre‐GT (1 week before GT), post‐GT, pre‐ & post‐GT, and control (no sL). One week before GT, top‐lighting photosynthetic photon flux density (PPFD) increased from 200 to 400 μmol m –2 s –1 in all groups, and sL power input was set to half the top‐lighting level. The pre‐ & post‐GT achieved the highest PMP yields per unit area, with a 16%–26% increase in PMP yield per unit lighting energy compared with the control. Overall, this lighting strategy offers a practical, scalable approach to more energy‐efficient PMP production under high‐density cultivation.
ABSTRACT Bio‐derived fuel refers to biofuels produced from organic materials originating from biomass or biowaste, industrial byproducts, municipal wastes, and animal effluents. To date, no single technology utilizes biomass and biowaste effectively to maximize bioenergy generation, as these technologies are at varying levels of technical and economic maturity. This review critically compares direct combustion, pyrolysis, transesterification, fermentation, and anaerobic digestion, together with mechanical, physicochemical, chemical, and biological pretreatment methods. Technologies of converting biomass and biowaste into bioenergy were critically evaluated based on conversion efficiency, processing time, energy density, emissions, technological maturity, and economic feasibility. Conventional and modern technologies for bio‐derived fuels were reviewed in terms of processing time, energy density, emissions, and cost. Biorefinery and bio‐derived fuel properties were compared with those of non‐renewable fuels. The review highlights advanced approaches for process optimization, bioreactor stability, and bio‐product improvement. Integrated biorefineries capable of co‐processing multi‐biomass and biowaste represent key future opportunities for producing multiple fuels and value‐added co‐products.
De novo biosynthesis of 4-vinylcatechol (VCAT), a valuable bio-based monomer and potent antioxidant, has emerged as a crucial objective due to its profound industrial and pharmacological significance. However, its biosynthesis is frequently hindered by limited precursor availability. In this study, we developed a highly efficient, dual-plasmid platform utilizing engineered Escherichia coli cell factories to synthesize VCAT directly from glucose without precursor feeding. To establish optimal production cells, we evaluated combinations of different host strains and phenolic acid decarboxylase (PAD) sources. Our results indicate that BL21(DE3) is less suitable for efficient de novo VCAT biosynthesis under the conditions tested. In contrast, the rpoA14(DE3), featuring a reprogrammed shikimate pathway, provided a more favorable host for VCAT production and enabled endogenous tyrosine supply, thereby eliminating the need for exogenous tyrosine supplementation required in BL21(DE3). To maximize this enhanced intracellular flux, we comparatively evaluated padC genes from different Bacillus subtilis strains. Comparative analysis demonstrated that the rpoA14(DE3)-10A5 exhibited significantly superior production titers, markedly outperforming both its 168-PAD counterpart and the standard BL21(DE3) expression hosts. Cultivated in single-step, aqueous fermentation at mild conditions, this optimal host-enzyme combination achieved de novo accumulation of 200 mg/L VCAT, promising scalable biosynthesis.
ABSTRACT This study investigated the effect of transitioning organic loading rates (OLR) and hydraulic retention times (HRT) on polyhydroxyalkanoates (PHA) production from wastewater using PHA‐accumulating phototrophic purple bacteria. These bacteria were cultivated under light‐feast anaerobic conditions in a photo‐assisted continuous stirred tank reactor (P‐CSTR) fed with acidogenic fermented cattle manure and sugarcane molasses. Transitioning OLRs of 0.7, 1.6, and 2.0 g COD/L.d were tested, followed by HRTs of 48, 72, and 112 h at the optimal OLR. The desired conditions to boost PHA production were an OLR of 0.7–1.2 g COD/L.d and HRT of 112 h, attaining a maximum PHA accumulation of 86.3% g PHA/g VSS, and production yield of 94.5% g COD PHA /g COD removed . The system also indicated efficient pollutant elimination of 96.6% NH 4 ‐N, and 82.5% COD. Shorter HRTs (48 h) were less effective in COD removal but promoted higher poly‐3‐hydroxyvalerate production in the copolymer content (48.8% of PHA). In contrast, poly‐3‐hydroxybutyrate content increased at high OLRs. The results highlight that transitioning OLR and varying HRT significantly influenced the process performance, PHA accumulation yield, and biopolymer quality. Thus, OLR and HRT are the critical control parameters for optimizing PHA production, tailoring polymer properties, and ensuring enhanced wastewater treatment.