• 学术搜索
  • 科研智能体
    • Research Labs
    • AI 阅读
    • AI 文库
    • 深度研究
    • 学者亮点
  • 学术资源
    • AI2000
    • 期刊/会议
    • 学者库
    • 学术API
      MCP&Skill
    • 溯源树
    • 数据集
  • 知识沉淀
    • 学术空间
订阅小程序
旧版功能
aminer vip
开通会员低至0.73元/天
一次搞定AI科研
立即登录
  • English
  • 联系方式
    Fatigue & Fracture Of Engineering Materials And Structures

    Fatigue & Fracture Of Engineering Materials And Structures

    JournalISSN 8756-758XeISSN 1460-2695中科院 材料科学 3区

    年发文量

    研究主题

    论文(5972)

    排序
    1Rolling Contact Fatigue Damage and Subsurface Microstructure Change of a Case‐Carburized CSS‐42L Steel
    Hua‐Zhen Jiang, Jiajun Liu,Jian Zhan, Zhengyang Li

    ABSTRACT To elucidate the rolling contact fatigue (RCF) failure mechanism of case‐carburized CSS‐42L gear steel, a plasto‐elastohydrodynamic lubrication (PEHL) model incorporating hardness gradients and surface roughness was integrated with twin‐roller RCF tests at 4.5–6.0 GPa. The maximum von Mises stress occurs at the subsurface. Because carburizing hardens the case and thus improves elastic load‐bearing capacity while suppressing plastic strain accumulation, the gradient model predicts a higher maximum von Mises stress but lower plastic and residual stresses than the homogeneous model. Higher contact pressure enlarges the plastic zone and asperity contact area ratio, shortening RCF life; life at 5.0 GPa is about 4.8 times that at 6.0 GPa, and carburizing extends life by at least 9.4 times at 4.5 GPa compared to original material. Subsurface spalling dominates the failure, and electron backscatter diffraction (EBSD) shows that carburizing increases dual‐carbide (M 7 C 3 and M 6 C) content within an ultrafine martensite matrix, enhancing RCF resistance.

    2026
    引用
    AI阅读
    加入学术空间
    2Mode‐II Contribution under Nominal Mode‐I Loading in Cementitious Material–Rock Interface TPB Tests
    Jian Ye,Wang Zhang,Hongwei Wang,Wen Xue, Cui Zhou,Hui Jin,Rena C. Yu,Zhimin Wu

    ABSTRACT Material mismatch and loading‐point deviations can induce Mode‐II contributions in nominal Mode‐I three‐point bending (TPB) tests of cementitious–rock interfaces. Finite element modeling using the interaction–integral method quantified the Mode‐II‐to‐Mode‐I stress intensity factor (SIF) ratio. The ratio was governed primarily by the elastic‐modulus ratio and modified by Poisson's ratio pairing, reaching 15.0% under centered loading at an elastic‐modulus ratio of 3.0. Load shifts toward the more compliant material increased the ratio, whereas shifts toward the stiffer material reduced it. The ratio varied nonmonotonically with initial crack‐height, peaking at an initial crack‐height ratio of approximately 0.5. Contour maps integrating material mismatch, loading‐point deviation, and initial crack‐height ratio identified initial crack‐height ratios of 0.2–0.3 and slight load shifts toward the stiffer material as preferable for reducing Mode‐II contributions. These findings support assessing crack‐tip mode mixity in nominal Mode‐I TPB tests of concrete–granite, concrete–marble, and sandstone–concrete interfaces.

    2026
    引用
    AI阅读
    加入学术空间
    3Creep–Fatigue Life Prediction of GH4169 Specimens under Uniaxial and Multiaxial Conditions by Integrating Continuum Damage Mechanics and Machine Learning
    Jia‐Ning Liu, Kai Yang,Hua‐Yan Hu, Wei Zeng, Ting Ye,Cheng‐Cheng Zhang, Zhong‐Lun Dai,Jian‐Feng Wen,Xian‐Cheng Zhang,Shan‐Tung Tu

    ABSTRACT Creep–fatigue interactions in aeroengine hot‐section components present significant challenges for life design and structural integrity assessment. This study proposes a framework integrating continuum damage mechanics (CDM) with machine learning (ML) to predict the creep–fatigue life of GH4169 specimens under both uniaxial and multiaxial conditions at 650°C. CDM simulations incorporating a multiaxial ductility factor generate a physics‐informed dataset covering different strain ranges, hold times, and stress states for smooth and hole specimens. Artificial neural network, random forest, and support vector machine (SVM) models are developed for crack initiation life prediction and validated against experimental data. The SVM model provides the best predictive performance. Based on the trained SVM model, the nonlinear degradation of creep–fatigue life and its strong sensitivity to hold time, particularly in hole specimens, are further analyzed. This approach provides an efficient and practical methodology for creep–fatigue life assessment of GH4169 components under complex stress states.

    2026
    引用
    AI阅读
    加入学术空间
    4Elastic‐Shakedown‐Informed Tensor‐History‐Based Critical‐Plane Fatigue Assessment under Proportional Loading
    Donglin Zhai,Zongyuan Zou, Zihan Cui, Yuhang Kang

    ABSTRACT Fatigue assessment of notched components remains difficult when local yielding, residual‐stress‐biased tensor histories, and critical‐plane damage metrics interact. This study develops an elastic‐shakedown‐informed tensor‐history workflow combining finite‐cycle numerical shakedown screening, stabilized Ramberg–Osgood material input, MRVD critical‐plane scanning, and an MCPES fatigue parameter. The workflow is benchmarked using published 34CrNiMo6 lateral U‐notch fatigue data; six candidate cases are screened and four cases satisfying the adopted finite‐cycle numerical shakedown‐screening criterion are retained for route comparison. The retained cases show case‐dependent agreement among nominal‐stress, pure‐elastic, Neuber–SWT, and shakedown‐consistent tensor‐history routes, while a hydraulic‐cylinder model illustrates route sensitivity under an amplified proportional‐pressure assessment condition. The results remain limited to the screened proportional‐loading cases and do not establish long‐term instability or experimentally verified component life. Accordingly, the study is presented as a finite‐cycle, path‐dependent mechanistic and numerical route‐comparison sensitivity study rather than a generally validated fatigue‐life framework.

    2026
    引用
    AI阅读
    加入学术空间
    5Comparing the Effect of Prior Exposure on the Durability of Boeing Space, Intelligence, and Weapons Systems LPBF Scalmalloy and LPBF 7A77
    Andrew Ang, Richard Aston, Shareen S. L. Chan,Nicole D. Schoenborn,Daren Peng,Rhys Jones

    ABSTRACT The US DoD Inspector General's Audit of the F/A‐18 fleet and the US Government Accountability Office's report into the sustainment of the F35 fleet have focused attention on the effect of the environment on structural integrity. Since Boeing Space, Intelligence, and Weapons Systems (BSI&WS) laser powder bed fusion (LPBF) Scalmalloy and LPBF 7A77, which are both additively manufactured aluminum alloys, are being considered for building limited‐life parts for military aircraft, this paper compares the effect of prior exposure to an aggressive environment on their durability and their equivalent initial damage sizes. We show that, whereas the 7A77 specimens had extensive corrosion after only 14 days of exposure to a 5% salt spray fog environment at 35°C, Scalmalloy showed little evidence of corrosion after 28 days. Subsequent fatigue tests found that 7A77 had a significantly lower fatigue life than Scalmalloy and that its fracture toughness was significantly lower than that of Scalmalloy.

    2026
    引用
    AI阅读
    加入学术空间
    立即登录,查看全部 5972 篇论文

    高被引作者

    作者引用发文
    Filippo Berto4195137
    Ali Fatemi376318
    Paolo Lazzarin305225
    Darrell Socie26621
    Kj Miller218036
    Luca Susmel183045
    Majid Reza Ayatollahi142620
    Andrea Carpinteri135135
    M.W. Brown123319
    Mohammad Reza Mohammad Aliha122329

    高产作者

    作者引用发文
    Filippo Berto4195137
    Luca Susmel183045
    Kj Miller218036
    Andrea Carpinteri135135
    Shan-Tung Tu67735
    Xiao-Ping Zhou99630
    Mohammad Reza Mohammad Aliha122329
    Sabrina Vantadori104729
    John R Yates81728
    Fuzhen Xuan72625

    相关期刊

    Engineering Fracture Mechanics
    International Journal of Fatigue
    International Journal of Fracture
    Archives of Civil and Mechanical Engineering
    Mechanics of Materials
    Theoretical and Applied Fracture Mechanics
    Strength of Materials
    International Journal of Impact Engineering
    International Journal of Pressure Vessels and Piping
    Procedia structural integrity