
Based on the optimized Co-containing La–Y–Ni superlattice hydrogen storage alloy matrix La0.4Y0.6Ni3.45Mn0.2Al0.15Co0.3, a series of La0.4₋ₓNdₓY0.6Ni3.45Mn0.2Al0.15Co0.3 alloys (x = 0, 0.1, 0.2, 0.3, 0.4) were designed and prepared in this work to investigate the effects of slight Nd substitution at the A-site on the phase structure, substructure matching, dehydrogenation thermodynamics, interfacial stability, and electrochemical kinetics of La–Y–Ni-based superlattice hydrogen storage alloys. The results show that, within the investigated Nd substitution range, all alloys retained a multiphase structure dominated by the A5B19-type Ce5Co19 and Pr5Co19 phases, together with a small amount of the CaCu5 phase, and no obvious structural transition was observed. With increasing Nd content, the CaCu5-type phase was gradually suppressed and nearly disappeared at x = 0.4, while the lattice parameters and unit cell volume of the main phases continuously decreased. The volumes of both the [A2B4] and [AB5] substructure units decreased, with the [A2B4] unit showing a more pronounced contraction, thereby improving the volume matching relationship between the substructures. Electrochemical measurements indicate that Nd substitution slightly shifted the discharge plateau upward, while the maximum discharge capacity gradually decreased from 396.9 mAh · g−1 to 365.7 mAh · g−1, suggesting that lattice contraction exerted a certain influence on the dehydrogenation thermodynamics. The capacity retention after 100 cycles (S100) increased from 84.6
This work investigated the influence of multi-walled carbon nanotube (MWCNT)-induced intergranular carbide on the hardness and corrosion behavior of elemental powder metallurgy Co-30Cr-5W-10Mn-xMWCNT (x = 0, 0.1, 0.5, and 0.8 wt
Ni-rich layered oxide cathodes deliver high specific capacity for lithium-ion batteries, yet inherent Li+/Ni2+ cation disorder and cyclic lattice distortion induce particle cracking and rapid capacity decay, limiting their large-scale deployment. In this work, Ta5+ was incorporated into LiNi0.6Co0.2Mn0.2O2 (NCM622) via a solid-state route to address structural instability. Owing to its high valence and strong Ta-O bonding, Ta5+ partially substitutes transition-metal sites and induces slight lattice expansion, which modifies the bulk lattice and facilitates Li+ transport; excess Ta preferentially segregates at particle surfaces/grain boundaries, forming Ta-rich surface species (likely LiTaO3-type) that stabilize the cathode–electrolyte interface. Combined XRD, SEM, HRTEM, EDS, and XPS characterizations confirm successful Ta incorporation, Ta surface enrichment, and retention of the layered framework, with the Ta-rich surface species contributing to interfacial stabilization. Electrochemical measurements prove the 1 mol
The increasing occurrence of pharmaceutical compounds in aquatic environments has raised concerns about potential impacts on ecosystem integrity and public health. Among these compounds, dexamethasone (DEX), a synthetic glucocorticoid widely used for its anti-inflammatory, antiallergic, and immunosuppressive properties, has attracted attention because of its potential endocrine-disrupting effects and its presence in water bodies. In this work, an electroanalytical method was developed for determining DEX in natural waters using a pencil graphite electrode (PGE). Cyclic voltammetry studies revealed a reduction peak at − 0.93 V vs. Ag/AgCl (3.0 mol L⁻¹ KCl), characteristic of an adsorption-controlled irreversible process, and an oxidation peak at + 0.83 V vs. Ag/AgCl (3.0 mol L⁻¹ KCl), corresponding to a process controlled by diffusion with an adsorption contribution and dependent on the preceding reduction step, possibly referring to the substance generated after the reduction process. Using square-wave voltammetry, linear analytical curves were obtained over the concentration range of 2.00–7.40 µmol L⁻¹. The limits of detection (LOD) and quantification (LOQ) were 0.20 and 0.67 µmol L⁻¹ in ultrapure water (78.5 and 263.0 µg L− 1), 0.20 and 0.68 µmol L⁻¹ in tap water (78.5 and 266 µg L− 1), and 0.52 and 1.70 µmol L⁻¹ in Billings dam water (204 and 667 µg L− 1), respectively. Recovery experiments in dam water yielded 83.7
Copper hexacyanoferrate (CuHCF) was used as a model Prussian blue analogue to examine relationships between synthesis conditions, material descriptors and voltammetric response. A full two-level factorial design with four centre points evaluated precursor concentration, CuCl₂ addition flow rate, temperature and stirring rate. X-ray diffraction, scanning electron microscopy with energy-dispersive X-ray spectroscopy, and cyclic voltammetry were used to examine crystallite size, image-derived average particle size, local Cu/Fe atomic ratio and electrochemical response. Pareto analysis indicated different factor and interaction patterns for the morphological, structural and compositional descriptors. The diffraction patterns were consistent with a CuHCF-type framework. Cathodic peak-current slopes versus the square root of scan rate were obtained as an empirical descriptors of the voltammetric response in LiNO₃ and KNO₃ electrolytes. The integrated analysis identifies exploratory associations between synthesis-controlled material characteristics and voltammetric behaviour, providing a basis for further studies with controlled electrode loading and ion-specific measurements.