
Abstract Mean stream water depth is an important physical component of streams. However, streams have high spatial heterogeneity, making depth determinations challenging. Most stream habitat assessments make direct manual point measurements in multiple cross‐channel transects. Alternatively, hydrologic and biogeochemical studies commonly use conservative solute additions to estimate mean reach depth. Here we compare estimates of mean water depth at the reach scale from these two widely used standard methods with data from a study of 72 stream reaches located across 8 biomes in the United States. Stream beds ranged from sealed concrete to boulder‐dominated and included urban, agricultural, and native habitats. Mean water depth was computed from direct measurement across 10–15 transects with 10 depth measurements per transect. Mean water depths from the two measurements were weakly but positively correlated, but the ratio of solute addition to direct measurements of depth varied from 0.12 to 5.8 among streams. Monte Carlo simulation based on variance in direct measurements suggests that at least 50 transects for depth and 20 transects for wetted width are required to reduce the 2.5 and 97.5 percentiles of modeled mean depth estimates to within 25% of the median across estimates. We conclude the two methods measure different but related aspects of stream structure. We suggest in streams with < 268 L/s discharge and 0.4 m reach average depth, direct measurements are most relevant to characterize water depth heterogeneity for geomorphology and habitat studies, whereas hydrology‐based studies are better served by conservative solute additions to estimate effective depth over a reach.
Abstract Reconstructing historical phosphorus (P) concentrations in lakes has been a long‐standing problem for paleolimnology. The most commonly applied method is the use of diatom‐inferred total P models, but there are well‐documented limitations to these approaches. Authigenic calcite co‐precipitated with P is a promising geochemical indicator of ambient P conditions in the water column through time. We tested two approaches for isolating the P content associated with authigenic calcite. The first capitalizes on a well‐known sequential extraction method but incorporates a physical separation to increase the specificity of the extraction. The second uses scanning electron microscopy and energy‐dispersive x‐ray spectroscopy (SEM‐EDS) to target P concentrations of authigenic calcite. These methods were evaluated using calcite‐rich sediments from Utah Lake in north‐central Utah, USA. Utah Lake is a eutrophic lake with a well‐documented increase in P pollution due to rapid population growth and wastewater inputs. Both methods showed increased up‐core concentrations of calcite‐P that match historical P loading records; however, a relatively high P detection limit reduced the effectiveness of the semi‐quantitative SEM‐EDS method. Overall, we demonstrate that the methods outlined here are feasible for reconstructing historical P concentrations in lakes with sufficient sedimentary authigenic calcite and appropriate sedimentary environments.
Abstract Sea level outputs from hydrodynamic models are often assessed against tide gauge data by comparing the standard deviations of modeled and observed time series, and by calculating the Pearson correlation coefficient and centered root mean square error (cRMSE) between the two. Together these metrics provide a compact evaluation of model skill; however, they are based on the implicit assumption that this skill is independent of both the timing and the duration of sea level deviations from the mean. In this study, we describe a complementary approach, utilizing the spectral information contained in numerical model outputs as well as in tide gauge records. We use a Ricker wavelet transform to express observed and modeled sea level in time‐frequency space, demonstrating our method for the Baltic Sea, an inland sea characterized by absence of strong tides. More precisely, we run a well‐established setup of the Nucleus for European Modelling of the Ocean (NEMO), and compare outputs against hourly data from tide gauges along the coast of Finland. We use the wavelet power spectrum and related quantities to assess how well our simulations capture sea level perturbations in the mesoscale and synoptic timescale ranges, and to illustrate seasonality in model errors at these different scales. In particular, our results show that spectral analysis can reveal qualitative differences in model performance between tide gauge stations; differences which the standard non‐spectral metrics fail to capture.
Understanding sound speed in natural waters is utilized in applications such as echo sounding, side scanning, temperature field tomography, evaluating compressibility and thermodynamic properties. While established approaches, such as the UNESCO formula and TEOS-10 package, describe sound speed in oceanic waters, the information about the contributions of specific solutes in water environments, however, is very scarce. In this work, we present systematic experimental data on the contribution of various electrolytes to sound speed in water, covering a temperature range from 1 degrees C to 30 degrees C and concentrations up to 0.05 mol L-1, which covers fully the freshwater range and goes slightly beyond it. We observed no evidence of nonlinearities both for temperature and concentration dependences within the studied range and our accuracy. Coefficients for calculating sound speed excess are provided for a range of salts containing all major ions commonly found in natural waters. Sound speed contributions in mixtures of salts can be directly added up and coefficients of the unmeasured ionic combinations can be numerically evaluated. Using our data, isothermal and adiabatic compressibility as well as in situ density can be calculated with an enhanced accuracy for any composition of common solutes. A numerical tool for evaluating sound speed at given ionic composition within the limnic pressure and temperature range has been developed.
Image-based approaches such as ZooScan are increasingly used for high-throughput zooplankton monitoring. However, quantitative evaluations of methodological differences relative to conventional microscopy remain limited. In this study, zooplankton abundance and size-based metrics obtained from microscopy and ZooScan image analysis were compared using identical subsamples from 35 net-collected samples collected between 2022 and 2023. Total zooplankton abundance showed strong agreement between the two methods at the community level (R-2 = 0.93, p < 0.001), with similarly high consistency for dominant taxonomic groups. In contrast, inferred size structure differed systematically between measurement approaches. Length-based metrics emphasized larger size classes, whereas equivalent spherical diameter-based metrics derived from ZooScan more strongly represented smaller size classes. Therefore, size-based results from the two approaches are not directly interchangeable. Although ZooScan produced abundance estimates comparable to those obtained by microscopy for dominant taxa under the identical-subsample comparison, the choice of size metric substantially influenced inferred size structure, highlighting the importance of accounting for method-dependent differences in zooplankton size-based analyses.