
Abstract Multiline anchors allow for the mooring of multiple floating offshore wind turbines (FOWTs), offering a cost-effective anchoring solution for large-scale floating offshore wind farms (FOWFs). However, their design is challenged by nonlinear load interactions and significant uncertainties in environmental and soil parameters. This necessitates a systematic exploration of the relationship between environmental parameters and mooring tensions, as well as the development of a reliability-based design framework for multiline anchors. This study quantifies the influence of wind speed, significant wave height, current speed, and load application angle on mooring tensions for single-line and multiline anchors using a 5-MW spar-type FOWT with a catenary mooring system, considering 4,180 combinations of environmental parameters. A new active-learning Kriging method is developed to construct accurate surrogate models that efficiently capture the nonlinear relationship between environmental parameters and mooring tensions, and is integrated into a reliability-based design framework. The proposed framework is applied to a representative FOWF consisting of seven FOWTs. The results reveal that wave height dominates the maximum mooring tension at windward mooring-line-connected anchors, whereas wind speed governs the maximum mooring tension at leeward mooring-line-connected anchors. For the top-mooring case, in which chain–soil interaction is neglected, the design diameters of multiline anchors are smaller than those of single-line anchors due to counterbalanced horizontal loads. In contrast, in the optimal-mooring case, where chain–soil interaction is considered, the design diameters of multiline anchors are larger because of the superposition of vertical load components.
Abstract Coastal wetlands are among the most valuable and productive ecosystems, but human-constructed barriers can disrupt hydrologic connectivity, leading to hypersalinity and wetland degradation. At Welder Flats, a state-designated wildlife management area on the central Texas coast, roads have restricted tidal exchange causing elevated salinities on the western side of the marsh. The resulting hypersalinity has contributed to the decline of Spartina alterniflora , reducing suitable habitat for the endangered Whooping Crane ( Grus americana ) and other migratory birds. This study examines hydraulic connectivity in anthropogenically altered wetlands and evaluates the suitability of Delft3D flexible mesh (FM) for fine-scale restoration planning. There is a notable lack of literature demonstrating the application of Delft3D FM in shallow (<1 m deep), fine-scale marsh systems containing sinuous tidal creeks (1 m wide) while simultaneously encompassing a regional-scale domain. A modeling framework to improve the performance of Delft3D FM in complex coastal wetlands at fine spatial resolutions in tandem with coarse regional resolutions was developed. Using this framework, a hydrologic connectivity analysis of Welder Flats was conducted to identify culvert configurations that enhanced tidal connectivity at Welder Flats, while avoiding erosive flow magnitudes. The results showed that installing a 5.49-m-wide culvert at the road location would increase flow by a factor of 36 in a formerly stagnant marsh. This study helped to inform engineering design plans for the future restoration of Welder Flats and demonstrated the utility of using Delft3D FM as a restoration planning tool to be utilized in future studies and restoration projects.
Abstract Coastal wetland erosion is a significant environmental concern along the Texas coast with various contributing factors. This paper evaluates wave activity at four coastal field sites near the Gulf Intracoastal Waterway (GIW) in Galveston Bay and quantifies the contributions of hurricanes, front events, and ship wake dynamics to the wetland boundary changes through eventful and seasonal field measurement campaigns. Utilizing the field hydrodynamic data, the wave-energy flux during the time of a Category 1 hurricane event (Hurricane Nicholas), prevailing warm or cold fronts, and ship wake dynamics are estimated to represent the erosion potential of wetland edges. The results revealed that Hurricane Nicholas contributed 13.3% of the wave-energy flux throughout the year (August 2021 to July 2022), warm or cold front events constituted 54.2%, and 11.2% were produced from ship wake hydrodynamics. The hurricane event exhibited the highest wave energy per occurrence, while front events led to the highest total wave energy throughout the year. Because of the typical shallow bay environment and heavy maritime traffic (measured at an average of 26 barge transits per day) along the channel, the total wave energy induced by vessel wakes accounts for a significant portion and needs to be considered when developing management strategies for the GIW.
The reliability of satellite-based significant wave height (SWH) and wind speed (Ws) measurements in the Gulf of Mexico is examined. Measurements derived from the SARAL/AltiKa, Jason-3, and Sentinel-3A altimeters are compared with in situ buoy observations from 10 National Oceanic and Atmospheric Administration (NOAA) buoys. Collocation windows of 40 km (spatially) and +/- 15 min for SWH and +/- 10 min for Ws (temporally) were used. Overall, results show strong correlations between satellite and buoy data. SARAL/AltiKa frequently exhibited the best overall performance for wave heights while Jason-3 tended to underestimate them, particularly the higher wave heights (> 2 m). Wind speed retrievals from all missions were also highly consistent with buoy data, with Sentinel-3A yielding the lowest scatter and most stable performance. No significant dependence on distance from the coast was observed, although minor improvements in wind speed accuracy occurred for offshore locations. The results confirm the fidelity of recent satellite altimeter data relative to in situ buoy data, with correlation coefficients exceeding 0.89 for SWH and 0.85 for Ws; it is hoped that these high correlations will spur greater use of altimeter measurements for model validation and data assimilation in the Gulf of Mexico.
This paper presents porting of a discontinuous Galerkin shallow water equation model (DG-SWEM version 3.0.2), a discontinuous Galerkin solver for hurricane storm surge, to NVIDIA graphics processing units (GPUs). Time-explicit discontinuous Galerkin methods contain a large number of degrees of freedom but have been shown to exhibit a large amount of data parallelism due to the loose coupling between elements and thus are naturally mapped to the central processing unit (CPU) architecture. A previous framework in porting DG-SWEM to GPUs required converting subroutines from Fortran to C + + to be used with CUDA C + +. By using OpenACC and unified memory, we simplified the porting process and maintained a single codebase for both CPU and GPU versions. We tested the code using a large Hurricane Harvey scenario on NVIDIA's Grace Hopper chip and compared the GPU code's performance on multiple H200 nodes to the CPU code on Grace and AMD Milan CPU nodes.