
The thermophysical parameters of cylindrical batteries are the key premise of studying the thermal runaway, so it is crucial to accurately measure the thermophysical parameters. At present, a variety of measurement methods have been proposed for thermophysical parameters of lithium-ion batteries, but the heat loss in the measurement process is rarely considered. In this article, an efficient and accurate measurement method is proposed. The measurement is carried out by combining the self-made adiabatic calorimeter and simulation. The standard part with known thermophysical parameters is used to compensate for the heat loss in the measurement process. The aerogel felt is used to replace the vacuum adiabatic environment. The standard part and the battery are heated in the same environment. The accuracy of the experimental results is verified by simulation. This proposed method measures the thermophysical parameters of the cylindrical lithium-ion battery without using expensive measuring instruments, which is time-consuming and accurate. It has great significance for subsequent thermal runaway research and the design of cooling systems for cylindrical batteries.
This study investigates the electrochemical performance and aging behavior of lithium-ion batteries (LIBs), focusing on the architectural effects of electrode and separator geometries alongside active material particle sizes. A pseudo-two-dimensional (P2D) model is employed to simulate lithium intercalation, solid diffusion, and coupled thermal behavior across a full-factorial design space. Despite its one-dimensional formulation, the model provides an optimal balance between computational efficiency and comparative predictive capability. A range of cell configurations is analyzed by varying anode, cathode, and separator thicknesses, as well as particle sizes, to assess their coupled impact on cell performance. The results demonstrate that while smaller particle diameters mitigate solid-state diffusion limitations and enhance capacity retention specifically under high C-rates, minimizing separator thickness significantly reduces inactive mass fractions, boosting baseline specific capacity even in designs with larger commercial particles. However, higher electrode loadings lead to increased volumetric heat-generation rates, particularly within thicker electrode configurations. A comparative assessment is also conducted in terms of cell mass, enabling the estimation of specific energy and power scaled to a standard format. Although limited to relative heat-generation trends by the one-dimensional thermal approximation, the results provide practical guidelines for advanced LIB design, successfully balancing electrochemical performance, volumetric engineering, and computational cost.
Lithium-ion batteries, owing to their high energy density and superior power characteristics, serve as a critical component for ensuring the stable and continuous operation of power systems. However, their high energy density and fast charge-discharge capability also lead to significant heat accumulation within battery packs. To address this issue, this study investigates the thermal management of a lithium battery pack using a novel direct-immersion liquid cooling structure through comsol multiphysics simulations. The cooling performance and temperature uniformity are enhanced by optimizing the coolant flow channel geometry and adjusting operating conditions. Model validation confirms the reliability of the simulation results. The effects of coolant inlet velocity, outlet position, coolant type, and deflector angle on the temperature and flow fields within the pack are systematically examined. Simulation results show that a coolant velocity of 4-5 m/s yields optimal cooling performance. The outlet placement along the positive x-axis or negative y-axis leads to better temperature uniformity compared to placement along the negative x-axis or positive y-axis. Low-viscosity coolants achieve more uniform coverage of the cooling region, while water-based fluid, combining high thermal conductivity with relatively low viscosity, provides the most favorable temperature distribution. Adjusting the deflector angle has a comparatively smaller influence on thermal behavior than varying the flow velocity, outlet position, or coolant type. The findings of this work provide a robust database for the design of immersed lithium-ion battery packs.
Lithium-rich layered oxide cathodes, Li-x[Ni0.8Mn0.1Co0.1]O-2, were synthesized via an oxygen-assisted coprecipitation method followed by calcination at 720 degrees C, 750 degrees C, and 780 degrees C. The introduction of O-2 during coprecipitation facilitates in situ oxidation of Mn2+ to higher valence states, leading to Mn-enriched regions within the hydroxide precursor that form Li2MnO3-like domains in the layered structure upon calcination. The primary objective of this study was to systematically investigate the effect of calcination temperature on crystal structure, Li/Ni cation ordering, microstructure, and electrochemical performance. Structural analysis revealed that the 750 degrees C annealed sample exhibits the lowest Li/Ni disorder, optimal hexagonal ordering, and a porous nanosheet-based morphology, which together promote rapid lithium-ion diffusion. Electrochemical testing shows that this sample achieves the highest initial discharge capacity (similar to 145 mAh/g), excellent capacity retention (85.4% after 100 cycles), and good rate capability (77.5% retention at 5C). Samples annealed at 720 degrees C and 780 degrees C showed reduced performance due to incomplete crystallization and microstructural collapse, respectively. This work demonstrates that optimizing calcination temperature in combination with O-2-assisted coprecipitation provides a scalable route to structurally robust lithium-rich NMC cathodes. While the initial capacity is lower than that of commercial NMC811, the study provides valuable insights into the interplay between synthesis conditions, structural ordering, and electrochemical behavior, highlighting design strategies for stable and reversible lithium-ion cathodes.
Abstract In situ characterization is used to understand internal short circuit (ISC)-caused thermal runaway of 4-Ah Li-ion cells with graphite anode and LiNi0.8Mn0.1Co0.1O2 (NMC811) cathode under different state-of-charge (SOC), cooling conditions, and electrolyte solvents. While 75% SOC led to thermal runaway, 50% and 25% SOC did not, which can be attributed to the rapid decrease of ISC current. The decrease is due to insufficient energy storage in the 25% SOC cell and due to separator shutdown in the 50% SOC cell. With liquid water cooling, the cell did not experience obvious damage with cooling temperature of 5 °C or 23 °C, but experienced thermal runaway when the cooling temperature was 60 °C. The difference can be attributed to higher ISC current and ISC heating rate at higher operating/cooling temperatures. The ratio of ethylene carbonate (EC) and ethyl methyl carbonate (EMC) in the electrolyte influenced cell capacity and ISC behaviors. EC-free electrolyte led to higher capacity and postponed the onset of thermal runaway, but the resulting thermal runaway is more severe and reached higher maximum temperatures, as compared to electrolyte with EC. The differences can be attributed to higher reactivity, higher conductivity, and lower combustion enthalpy of EC as compared to EMC. These findings demonstrated that in situ characterization can enhance the understanding of ISC and thermal runaway behaviors of Li-ion cells by providing details of the transient and localized phenomena.