• 学术搜索
  • 科研智能体
    • Research Labs
    • AI 阅读
    • AI 文库
    • 深度研究
    • 学者亮点
  • 学术资源
    • AI2000
    • 期刊/会议
    • 学者库
    • 学术API
      MCP&Skill
    • 溯源树
    • 数据集
  • 知识沉淀
    • 学术空间
订阅小程序
旧版功能
aminer vip
开通会员低至0.73元/天
一次搞定AI科研
立即登录
  • English
  • 联系方式
    Fibers

    Fibers

    JournalISSN 2079-6439eISSN 2079-6439中科院 材料科学 3区

    年发文量

    研究主题

    论文(1190)

    排序
    1Inverse-Analysis Identification of Material Parameters in Hybrid-Reinforced (bars Plus Fibers) Concrete Beams Through the Updated Bridged Crack Model (UBCM)
    Bineet Kumar, Dongxi Xie,Alberto Carpinteri

    Hybrid-reinforced concrete (HRC) beams exhibit a complex flexural response governed by the interaction between matrix cracking, fiber pull-out, and steel-bar yielding, which complicates the identification of constituent properties from global load–deflection data. This study develops an inverse-analysis procedure based on the Updated Bridged Crack Model (UBCM), in which concrete matrix, discontinuous steel fibers, and longitudinal reinforcement are represented as mechanically distinct phases. An experimental database comprising 48 four-point-bending tests was considered. For transparent interpretation and parameter-sensitivity assessment, the identification was performed sequentially using plain-concrete, fiber-reinforced concrete, and reinforced-concrete specimens. Effective matrix modulus and fracture toughness, equivalent fiber pull-out force, critical pull-out displacement, and steel yield strength were identified from seven calibration configurations. A multi-objective optimization was employed for the fiber parameters by minimizing discrepancies in the maximum load and area under the load–deflection response. Further nine HRC configurations experimental results are used to validate the numerical predictions by UBCM. The UBCM reproduced first-cracking condition, post-cracking load recovery, fiber-controlled softening, and transition towards steel-controlled yielding. The results demonstrate that constituent properties governing HRC fracture can be identified and transferred while retaining their physical meaning and role.

    2026
    引用
    AI阅读
    加入学术空间
    2Dyeing of Cotton Fabric Using Beta Vulgaris Peel Extracts and Bio-Mordants for Enhanced Ultraviolet Protection and Antioxidant Activity—A Comparative Approach
    Faiza Anwar,Ahmad Fraz,Kashif Javed,Asfandyar Khan, Arslan Shafi,Nazmul Islam,Zeeshan Tariq,Imran Ahmad Khan

    Natural dyes extracted from agricultural waste are increasingly valued due to their biodegradability and minimal ecological risks. This study explores the extraction of dyes from Beta vulgaris (beetroot) peels in different media (water, ethanol, and methanol) using a Soxhlet apparatus. The extracted dyes were applied to cotton fabric at 2%, 3%, and 4% concentrations on the weight of fabric through the exhaust method at a liquor ratio of 1:30, maintaining a temperature of 90 °C for 90 min, following a simultaneous mordanting technique using orange peel, lemon peel, Terminalia chebula (myrobalan), and gum acacia as bio-mordants. The dyed fabrics were assessed for color strength (K/S) at maximum wavelength (λmax = 537 nm) and colorfastness properties, including washing, light, rubbing, and perspiration fastness, following standard testing protocols. The antioxidant and ultraviolet protection properties were established to determine the functional performance of the dyed fabrics. The K/S values obtained on cotton fabric with the extracts in organic solvents (methanol and ethanol) were higher than the K/S values obtained with the aqueous extract. The maximum K/S value was 4.57 for cotton dyed with 4% methanolic beetroot extract using orange peel as a bio-mordant, followed by 4.44 for the corresponding ethanolic extract; the maximum K/S value obtained with the aqueous extract was 2.81. The mordant type also has an influence on the color strength and colorfastness performance. Washing fastness ratings ranged from 3–4 to 4–5 on the gray scale, dry rubbing fastness ranged from 3–4 to 4–5, and light fastness ranged from 2–3 to 4–5 on the blue wool scale, depending on extraction medium, dye concentration, and bio-mordant. The samples dyed in the presence of bio-mordants, particularly orange peel and lemon peels, rendered excellent ultraviolet protection and antioxidant activities, followed by myrobalan and then gum acacia. The maximum ABTS radical inhibition was 88.20 ± 8.5%, and the maximum ultraviolet protection factor (UPF) was 88; both were recorded for cotton dyed with 4% ethanolic beetroot extract using orange peel as a bio-mordant.

    2026
    引用
    AI阅读
    加入学术空间
    3Waste-Derived Oil Palm Mesocarp Fiber in LLDPE Biocomposites: Low-Loading Mechanical and Moisture Response
    Muhammad Irfan Nuryanta,Rahmat Doni Widodo, Ahmad Mujaki,Hendrix Noviyanto Firmansyah, Rizky Ajie Aprilianto, Betti Ses Eka Polonia, Edi Purnomo,Urip Agus Salim,Gesang Nugroho,Muhammad Akhsin Muflikhun

    Waste-derived oil palm mesocarp fiber (OPMF) has potential as a lignocellulosic reinforcement for thermoplastic composites. The same trend in strength, stiffness, and moisture-related properties does not always hold at relatively low fiber loadings. This study examined these property changes in linear low-density polyethylene (LLDPE) biocomposites. Composites containing 0, 5, 10, and 15 wt% alkali-treated OPMF were produced by hot compression molding. Tensile and flexural properties, density, 24 h water absorption, and water contact angle were evaluated, supported by scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), and differential scanning calorimetry (DSC). The 5 wt% composite showed the highest mean tensile and flexural strengths of 16.16 ± 1.14 MPa and 29.33 ± 3.57 MPa, while the highest apparent tensile modulus (521.25 ± 38.84 MPa) and flexural modulus (0.888 ± 0.122 GPa) occurred at 10 wt%. Water absorption increased from 0.06 ± 0.01% to 1.19 ± 0.12%, while the contact angle decreased from 97.78 ± 2.04° to 65.18 ± 5.21°. Strength, stiffness, and moisture response followed different loading-dependent trends, indicating a composition-dependent strength–stiffness–moisture trade-off within the investigated range.

    2026
    引用
    AI阅读
    加入学术空间
    4On the Tensile Failure of Single Carbon Fibers Subjected to Transverse Loading
    Karan Shah,Subramani Sockalingam

    This study investigates the applicability of the transverse loading technique for inducing tensile failure in single IM7 carbon fibers of nominal diameter 5.2 µm over a range of microscale gagelengths. Transverse loading experiments and finite element simulations are performed using different indenter tip radii (R~500 µm, 100 µm, 50 µm, and 20 µm) and fiber starting angle configurations to characterize the resulting multiaxial stress state and identify loading configurations that promote tensile failure. Fiber failure under transverse loading is studied in terms of the experimentally determined global (far-field) axial failure stress and the locally induced axial tensile, axial compressive and transverse compressive stresses induced within the fiber–indenter contact region. SEM images of failed fiber ends retrieved after testing are also used to gain insights into the fiber failure under different loading conditions. The results show that bending-induced axial compressive stresses become more pronounced with decreasing indenter tip radii and increasing fiber starting angle and are expected to govern fiber failure. Tensile fiber failure is expected to occur only for R~100 µm indenter at all starting angles and for R~50 µm indenter at 0°. These loading configurations induce axial tensile stress concentrations of magnitude SCF~2.5–2.8 over a range of microscale lengths lσ,max~5−70 μm. However, fiber failure is not consistently expected to occur within the stress concentration region because the axial tensile stress field is comprised of both a localized stress-concentration region and a uniformly stressed region, allowing failure to initiate in either region in accordance with weakest-link statistics. Thus, the effective gagelength cannot be defined solely by the length of the induced stress concentrations and requires consideration of the entire axial stress distribution of the fiber along with weakest link statistics which is beyond the scope of the current study. The identified combinations of indenter geometry and fiber starting angle in this study provide a basis for determining fiber tensile strength distribution at microscale gagelengths.

    2026
    引用
    AI阅读
    加入学术空间
    5Tensile and Flexural Behavior of CFRP-Reinforced Notched Aluminum Produced by Wet Layup and Vacuum Bagging
    Jacey Wright, John Weatherford,Morgan Sikes,Siavash Sattar

    Notches and localized defects can substantially reduce the load-bearing capacity of aluminum components by creating stress concentrations that promote premature failure. Externally bonded CFRP reinforcement offers a lightweight approach for restoring load-carrying capacity in damaged aluminum components. Direct experimental comparisons of wet-layup and vacuum-bagged CFRP reinforcement for notched aluminum under both tensile and flexural loading remain limited. This study investigates the tensile and flexural behavior of notched 6061-T6511 aluminum specimens reinforced with woven carbon fiber-reinforced polymer (CFRP) using manual wet layup and vacuum bagging. Two- and four-ply reinforcement configurations were evaluated, with five specimens tested for each condition. All CFRP-reinforced configurations increased the mean nominal strength and apparent modulus relative to the untreated notched specimens. The wet-layup two-ply configuration provided the greatest strength recovery, increasing nominal tensile strength from 141.88 to 245.89 MPa and nominal flexural strength from 213.84 to 384.81 MPa, corresponding to improvements of approximately 73% and 80%, respectively. Vacuum-bagged specimens exhibited higher apparent tensile moduli than the corresponding wet-layup specimens but lower tensile and flexural strengths. The wet-layup four-ply configuration produced the highest apparent flexural modulus, whereas the vacuum-bagged four-ply configuration produced the highest apparent tensile modulus. Increasing the CFRP reinforcement from two to four plies consistently increased the apparent tensile and flexural moduli but produced limited or reduced nominal strength, depending on the processing method and loading condition. These findings show that CFRP reinforcement can restore a substantial portion of the strength and apparent stiffness lost due to notching and highlight the importance of selecting the processing method and ply count based on the required balance between strength and stiffness.

    2026
    引用
    AI阅读
    加入学术空间
    立即登录,查看全部 1190 篇论文

    高被引作者

    作者引用发文
    Carlo Santulli49511
    Constantin Ε. Chalioris4659
    Sivasubramanian Palanisamy3788
    Ton Peijs3354
    Mariappan Kadarkarainadar Marichelvam3232
    Mohammad Asim3191
    Mohammad Jawaid3191
    Anwar Kasim3133
    Hairul Abral3133
    N. Rajini3006

    高产作者

    作者引用发文
    Dieter Veit323
    Carlo Santulli49511
    oleg g morozov9010
    Constantin Ε. Chalioris4659
    Rosalda Punturo738
    Roman Fediuk2958
    Andrea Ehrmann1728
    Sivasubramanian Palanisamy3788
    Chris G. Karayannis2597
    Sergey Klyuev2647

    相关期刊

    Journal of engineered fibers and fabrics
    Reviews on Advanced Materials Science
    Journal of Reinforced Plastics and Composites
    Journal of Industrial Textiles
    Advances in Polymer Technology
    Journal of Thermoplastic Composite Materials
    Journal of Renewable Materials
    Polymers and Polymer Composites
    Revista Materia
    Composites Part C: Open Access