
A benchmark-based neutronic and steady-state thermal-hydraulic assessment was performed to evaluate beryllium reflector configurations for enhancing irradiation capability in the MTR-10 MW research reactor. The reference one-trap core was modified to a symmetric four-trap layout, and a constrained sequence of graphite and beryllium reflector substitutions was assessed with MCNP4C2/MTRMC. The four-trap configuration reduced the initial excess reactivity from 141.71 to 82.85 mk. The selected 22-block beryllium reflector recovered the excess reactivity to 139.38 mk, corresponding to 96.04% recovery of the reactivity loss relative to the shifted four-trap base case. The four-site average thermal neutron flux increased from the reference central-trap mean of 1.055 × 10 14 to 1.319 × 10 14 n·cm -2 ·s -1 , an average gain of 25.0%, while the maximum site reached 1.904 × 10 14 n·cm -2 ·s -1 . After applying a comparable active neutron-history basis, OpenMC reproduced the same recovery trend, giving 96.94% recovered reactivity. The steady-state thermal-hydraulic assessment used CAUDVAP/TERMIC-1H at 550 m 3 /h, giving a total mass flow rate of 151.607 kg/s and a mean pressure drop of 5.372 kPa. The maximum plate power in the hottest fuel element was 28.93 kW, giving a hot-plate peaking factor of 1.24 and a hot-plate heat-flux input of 49.4 W/cm 2 . The TERMIC-B2 case at 50 W/cm 2 therefore represents the rounded-up hot-plate condition for the final configuration, with redistribution and DNB ratios above unity over the assessed hot-channel velocity interval.
The paper presents the results of an experimental study and comparative analysis of coolant hydrodynamics at the outlet of a fuel assembly (FA) with upper nozzles of three different designs. The FAs are intended for the core of the RITM reactor of a small nuclear power plant (SNPP). The aim of the work was to study the axial flow velocity at the outlet of the fuel rod bundle and behind the upper nozzles of different designs, as well as to identify regions of the fuel rod bundle from which flow could enter the sampling tube leading to a resistance thermometer (RTD). The experiments were conducted on an experimental test bench with an air working fluid using a model of the FA outlet section. The model consisted of a fragment of the fuel rod bundle, replaceable mock-ups of the upper nozzles for three design variants, as well as mock-ups of the mounting plate for the FA and the coolant sampling tube to the RTD. The pneumometric method was used to determine the axial flow velocity. The tracer injection method was employed to identify the regions of the fuel rod bundle from which flow could enter the sampling tube to the RTD. The hydrodynamic flow pattern is presented in the form of maps of axial velocity and tracer concentration. The experimental results allowed detailing the turbulent flow structure and led to the following conclusions. The shape of the flow passage of the upper nozzle confusor has little effect on the axial flow already before the outlet spacer grid. However, a significant effect of the flow path geometry of the upper nozzles is manifested when the flow exits the fuel rod bundle. The shape of the confusor flow passage and the flow path geometry of the upper nozzles have a considerable influence on the axial velocity magnitude and flow structure. The greatest contribution to the change in axial velocity comes from the reduction in the flow passage area of the upper nozzles. The non-uniformity of the flow structure from the upper nozzle windows is determined by the sampling tube, which blocks part of the flow passage. The flow exiting the upper nozzle with three windows is the most non-uniform. During flow through the upper nozzle confusors, a mixing process is observed, expressed as a displacement of the tracer toward the sampling tube. The greatest transverse tracer displacement occurs in the confusor of the three-window upper nozzle. To minimize the influence of flows with different temperatures on the RTD readings, it is necessary to use upper nozzles with three windows. The research results have been used by specialists of JSC “OKBM Afrikantov” to substantiate engineering solutions in core design.
Neutronic analysis of nuclear fuel assemblies is crucial for optimizing reactor core design. The conventional techniques involve computationally expensive simulations. This work explores the feasibility of developing efficient machine-learning models for neutronic analysis. This was done by leveraging artificial neural networks (ANNs) for evaluating two important neutronic parameters: neutron multiplication factor (k ∞ ) and void coefficient (α v ), of 17 × 17 pressurized water reactor (PWR) fuel assemblies. OpenMC neutronics code was employed to generate a training set of 6000 data points for the machine learning models with six input parameters: U-235 enrichment, densities of fuel and moderator, concentration of burnable poisons in fuel and moderator, and fuel pitch. Results reveal that the four-layer ANN model with sigmoid activation functions in the hidden layers exhibited excellent performance. The ANN predicts k ∞ with an average predictive error below 106 pcm, well within the acceptable limit of 500 pcm. Among the optimization algorithms employed, the simplex search method outperformed genetic algorithms, simulated annealing and particle swarm optimization. Utilizing the developed ANN model in simplex search, the correlation was derived for fuel pitch separating the under- and over-moderated regions under cold zero power (CZP) conditions. It was observed that the fuel pitch must be kept ≤ 1.434 cm to maintain the reactor’s under-moderated status throughout its operational lifetime. Overall, the accuracy of ANN model was found to be satisfactory, opening doors for further improvements.
Theoretical excitation functions for the alpha particle-induced reactions 59 Co(α,2p4n) 57 Co, 59 Co(α,2pn) 60 Co, and 59 Co(α,4p5n) 54 Mn were analyzed and compared to the experimental excitation functions. Experimental cross sections were calculated using the PACE4 and TALYS-2.0 statistical model codes across an energy range of 33.1–54.5 MeV. PACE4 calculations used different values of level density parameters at k = 8–10, while TALYS-2.0 calculations were performed with multiple level density models (ldmodel 1–5). The analysis also examined the sensitivity and uncertainty of theoretical cross sections to changes in level density parameter. A quantitative comparison of the experimental and theoretical excitation functions was performed using calculations of reduced chi-square (χ 2 red ) and normalized root mean square deviations (NRMSD). The findings indicate that PACE4 calculations more accurately reflect both the size and form of the experimental excitation functions compared to TALYS-2.0 calculations for the reaction channels studied. The quantitative analysis indicates the predominance of the compound nucleus reaction mechanism, suggesting that pre-equilibrium and direct contributions have a minimal impact within the energy ranges studied. This study provides a thorough justification for the nuclear theoretical models and offers consistent nuclear reaction data for alpha particle-induced reactions on a 59 Co target.
Today, thermal reactors, which are the basis of modern Russian nuclear energy, can consume plutonium, but in limited quantities and with a low content of threshold isotopes, so their fuel supply is actually limited by natural uranium reserves. Fast reactor technology was created for extended production of plutonium and their fuel supply capabilities are limited by the resources of 238U, which is two orders of magnitude more than 235U. The paper presents the following possible functions of fast reactors in the future two-component nuclear energy system, the transition to which in the coming decades is a strategic goal of the Rosatom State Corporation: electricity generation; maintenance the balance of plutonium in the system of fast and thermal reactors; “refinement” of plutonium from spent nuclear fuel in thermal reactors; disposal of long-lived nuclear energy wastes; production of isotopes highly demanded by the industry and medicine. Obviously, the specialized fast reactors creation will be required to increase the efficiency of these functions. As a result, thermal and fast reactors can be used to create a sustainable, multi-functional and waste-free new nuclear power industry with an almost unlimited fuel resource.