In the present investigation, we study the propagation of plane waves in heat conducting micropolar fluid. The phase velocity, attenuation coefficient, specific loss, and penetration depth are computed numerically and depicted graphically. In addition, the fundamental solutions of the system of differential equations in case of steady oscillations are constructed. Some basic properties of the fundamental solution and special cases are also discussed.
This mathematical study is related to heat transfer under peristaltic flow of fractional second-grade fluid through nonuniform cylindrical tube with permeable walls. The analysis is performed under low Reynolds number and long wavelength approximation. The analytical solution for pressure gradient, friction force, and temperature field is obtained. The effects of appropriate parameters such as Grashof number, nonuniformity of tube, permeability of tube wall, heat source/sink parameter, material constant, fractional time derivative parameter and amplitude ratio on pressure rise, friction force, and temperature distribution are discussed. It is found that an increase in amplitude ratio and material constant causes increase in pressure but increase in nonuniformity of the tube causes decrease in pressure. It is also observed that variation of friction force against flow rate shows opposite behavior to that of pressure. Increase in temperature is also observed due to increase in heat source/sink parameter at inlet as well as downstream.
The paper considers the applied problems of hydrodynamics and based on the new results, published by the author in recent years, shows that main assumptions used in the course of their solution, namely, incompressibility of liquids and potentiality of their movement, are not applicable to liquids in the gravitational field of the Earth.
Most existing equations for predicting local scour at bridge piers suffer from overprediction of the scour depths which results in higher foundation costs. To tackle this problem, a mathematical model for predicting bridge pier scour is developed herein based on an energy balance theory. The present study equation was compared to commonly used bridge scour equations using scour field data in USA. The developed equation has several advantages among which we have the following: it adds to the understanding of the physics of bridge pier scour, is valid for slender and wide piers, does not suffer from overprediction of scour depths, addresses clear water and live bed scour, and includes the effects of various characteristics of the bed material such as specific gravity (or density), porosity, size, and angle of repose. In addition, the developed equation accounts for the debris effect and aids in the design of scour mitigation methods such as collars, side bars, slots, and pier protective piles.
Narrow annular drilling such as casing-while-drilling technique is gaining popularity due to its ability to mitigate nonproductive time during oil and gas drilling operations. However, very little is known about the flow dynamics in narrow annular drilling. In this study, the Eulerian-Eulerian two-fluid model was used to examine the influence of Yield Power Law fluid rheological properties on cuttings transport in eccentric horizontal narrow annulus. The flow was assumed as fully developed, laminar, and transient state. The present simulation model was validated against experimental data, where a mean percent error of −1.2% was recorded. Results revealed an increase in the radial distribution of cuttings transport velocity in the wide annular region as the consistency index, K, and the flow behavior index, n, increase. Nonetheless, increasing the yield stress, τo, had insignificant effect on the cuttings transport velocity. Three-dimensional profiles showed how cuttings preferred to travel in less resistant flow area, whereas cuttings concentration builds up in the narrow annular region. Furthermore, annular frictional pressure losses also increased as K, n, and τo increased. This study serves as a guide to properly optimize drilling fluid rheological properties for efficient cuttings transport and equivalent circulating density (ECD) management in narrow annular drilling.
Wake reduction is a crucial link in the chain leading to undetectable watercraft. Here, we explore a volumetric approach to controlling the wake in a stationary flow past cylindrical and spherical objects. In this approach, these objects are coupled with rigid, fluid-permeable structures prescribed by a macroscopic design approach where all solid boundaries are parameterized and modeled explicitly. Local, gradient-based optimization is employed which permits topological changes in the manifold describing the composite solid component(s) while still allowing the use of adjoint optimization methods. This formalism works below small Reynolds number (Re) turbulent flow (Re≈100–10,000) when simulated using small Reynolds-averaged Navier-Stokes (RANS) models. The output of this topology optimization yields geometries that can be fabricated immediately using fused deposition modeling (FDM). Our prototypes have been verified in an experimental water tunnel facility, where the use of Particle Image Velocimetry (PIV) described the velocity profile. Comparisons with our computational models show excellent agreement for the spherical shapes and reasonable match for cylindrical shapes, with well-understood sources of error. Two important figures of merit are considered: domain-wide wake (DWW) and maximum local wake (MLW), metrics of the flow field disturbance whose definitions are described.
The intrauterine fluid flow due to myometrial contractions is peristaltic type motion and the myometrial contractions may occur in both symmetric and asymmetric directions. The channel asymmetry is produced by choosing the peristaltic wave train on the walls to have different amplitude, and phase due to the variation of channel width, wave amplitudes and phase differences. In this paper, we study the effects of heat and mass transfer on the peristaltic transport of magnetohydrodynamic couple stress fluid through homogeneous porous medium in a vertical asymmetric channel. The flow is investigated in the wave frame of reference moving with constant velocity with the wave. The governing equations of couple stress fluid have been simplified under the long wave length approximation. The exact solutions of the resultant governing equations have been derived for the stream function, temperature, concentration, pressure gradient, and heat transfer coefficients. The pressure difference and frictional forces at both the walls are calculated using numerical integration. The influence of diverse flow parameters on the fluid velocity, pressure gradient, temperature, concentration, pressure difference, frictional forces, heat transfer coefficients, and trapping has been discussed. The graphical results are also discussed for four different wave shapes. It is noticed that increasing of couple stresses and heat generation parameter increases the size of the trapped bolus. The heat generation parameter increases the peristaltic pumping and temperature.
Off-axis collisions of two equal size droplets are investigated numerically. Various governing processes in such collisions are discussed. Several commonly used theoretical models that predict the onset of separation after collision are evaluated based on the processes observed numerically. A separation criterion based on droplet deformation is found. The numerical results are used to assess the validity of some commonly used phenomenological models for drop separation after collision. Also, a critical Weber number for the droplet separation after grazing collision is reported. The effect of Reynolds number is investigated and regions of permanent coalescence and separation are plotted in a Weber-Reynolds number plane for high impact parameter collisions.
This paper describes the peristaltic flow of an incompressible viscous fluid in a tapered asymmetric channel with heat and mass transfer. The fluid is electrically conducting fluid in the presence of a uniform magnetic field. The propagation of waves on the nonuniform channel walls to have different amplitudes and phase but with the same speed is generated the tapered asymmetric channel. The assumptions of low Reynolds number and long wavelength approximations have been used to simplify the complicated problem into a relatively simple problem. Analytical expressions for velocity, temperature, and concentration have been obtained. Graphically results of the flow characteristics are also sketched for various embedded parameters of interest entering the problem and interpreted.
Two-dimensional MHD mixed convection boundary layer flow of heat and mass transfer stagnation-point flow of a non-Newtonian power-law nanofluid towards a stretching surface in the presence of thermal radiation and heat source/sink is investigated numerically. The non-Newtonian nanofluid model incorporates the effects of Brownian motion and thermophoresis. The basic transport equations are made dimensionless first and the complete nonlinear differential equations with associated boundary conditions are solved numerically by finite element method (FEM). The numerical calculations for velocity, temperature, and nanoparticles volume fraction profiles for different values of the physical parameters to display the interesting aspects of the solutions are presented graphically and discussed. The skin friction coefficient, the local Nusslet number and the Sherwood number are exhibited and examined. Our results are compatible with the existing results for a special case.
The similarity equations for the Bödewadt flow of a non-Newtonian Reiner-Rivlin fluid, subject to uniform suction/injection, are solved numerically. The conventional no-slip boundary conditions are replaced by corresponding partial slip boundary conditions, owing to the roughness of the infinite stationary disk. The combined effects of surface slip (λ), suction/injection velocity (W), and cross-viscous parameter (L) on the momentum boundary layer are studied in detail. It is interesting to find that suction dominates the oscillations in the velocity profiles and decreases the boundary layer thickness significantly. On the other hand, injection has opposite effects on the velocity profiles and the boundary layer thickness.
The paper presents a numerical investigation of non-Newtonian modeling effects on unsteady periodic flows in a two-dimensional (2D) constricted channel with moving wall using finite volume method. The governing Navier-Stokes equations have been modified using the Cartesian curvilinear coordinates to handle complex geometries, such as, arterial stenosis. The physiological pulsatile flow has been used at the inlet position as an inlet velocity. The flow is characterized by the Reynolds numbers 300, 500, and 750 that are appropriate for large arteries. The investigations have been carried out to characterize four different non-Newtonian constitutive equations of blood, namely, the (i) Carreau, (ii) Cross, (iii) Modified-Casson, and (iv) Quemada. In these four models, blood viscosity is a nonlinear function of shear rates. The Newtonian model has been investigated to study the physics of fluid and the results are compared with the non-Newtonian viscosity models. The numerical results are presented in terms of streamwise velocity, wall shear stress, pressure distribution as well as the vorticity, streamlines, and vector plots indicating recirculation zones at the poststenotic region. Comparison has also been illustrated in terms of wall pressure and wall shear stress for the Cross model considering different amplitudes of wall oscillation.
Unsteady as well as steady natural convection flow in a vertical channel in the presence of uniform magnetic field applied normal to the flow region and temperature dependent variable thermal conductivity is studied. The nonlinear partial differential equations governing the flow have been solved numerically using unconditionally stable and convergent semi-implicit finite difference scheme. For steady case, approximate solutions have been derived for velocity, temperature, skin friction, and the rate of heat transfer using perturbation series method. Results of the computations for velocity, temperature, skin friction, and the rate of heat transfer are presented graphically and discussed quantitatively for various parameters embedded in the problem. An excellent agreement was found during the numerical computations between the steady-state approximate solutions and unsteady numerical solutions at steady-state time. In addition, comparison with previously published work is performed and the results agree well.
The phase separation behaviors of PEG1000/sodium citrate, PEG4000/sodium citrate, PEG1000/ammonium sulfate, and PEG4000/ammonium sulfate aqueous two-phase systems were investigated, respectively. There are two distinct situations for the phase separation rate in the investigated aqueous two-phase systems: one state is top-continuous phase with slow phase separation rate and strong bottom-continuous phase with fast phase separation rate and weak volume ratio dependence. The system properties such as density, viscosity, and interfacial tension between top and bottom phases which have effects on the phase separation rate of aqueous two-phase systems were measured. The property parameter differences between the two phases increased with increasing tie line length and then improved the phase separation rate. Moreover, a modified correlation equation including the phase separation rate, tie line length, and physical properties of the four aqueous two-phase systems has been proposed and successfully tested in the bottom-continuous phase, whose coefficients were estimated through regression analysis. The predicted results of PEG1000/sodium citrate aqueous two-phase systems were verified through the stationary phase retention in the cross-axis countercurrent chromatography.
An analysis is carried out to study the steady two-dimensional flow of an incompressible viscous fluid past a porous deformable sheet, which is stretched in its own plane with a velocity proportional to the distance from the fixed point subject to uniform suction or blowing. A uniform shear flow of strain rate β is considered over the stretching sheet. The analysis of the result obtained shows that the magnitude of the wall shear stress increases with the increase of suction velocity and decreases with the increase of blowing velocity and this effect is more pronounced for suction than blowing. It is seen that the horizontal velocity component (at a fixed streamwise position along the plate) increases with the increase in the ratio of shear rate β and stretching rate (c) (i.e., β/c) and there is an indication of flow reversal. It is also observed that this flow reversal region increases with the increase in β/c.
The performance of fluid pumps based on Wankel-type geometry, taking the shape of a double-lobed limaçon, is characterized. To the authors’ knowledge, this is the first time such an attempt has been made. To this end, numerous simulations for three different pump sizes were carried out and the results were understood in terms of the usual scaling coefficients. The results show that such pumps operate as low efficiency (<30%) valveless positive displacements pumps, with pump flow-rate noticeably falling at the onset of internal leakage. Also, for such pumps, the mechanical efficiency varies linearly with the head coefficient, and, within the onset of internal leakage, the capacity coefficient holds steady even across pump efficiency. Simulation of the flow field reveals a structure rich in three-dimensional vortices even in the laminar regime, including Taylor-like counterrotating vortex pairs, pointing towards the utility of these pumps in microfluidic applications. Given the planar geometry of such pumps, their applications as microreactors and micromixers are recommended.
Hydraulic analysis of water distribution networks is an important problem in civil engineering. A widely used approach in steady-state analysis of water distribution networks is the global gradient algorithm (GGA). However, when the GGA is applied to solve these networks, zero flows cause a computation failure. On the other hand, there are different mathematical formulations for hydraulic analysis under pressure-driven demand and leakage simulation. This paper introduces an optimization model for the hydraulic analysis of water distribution networks using a metaheuristic method called shuffled complex evolution (SCE) algorithm. In this method, applying if-then rules in the optimization model is a simple way in handling pressure-driven demand and leakage simulation, and there is no need for an initial solution vector which must be chosen carefully in many other procedures if numerical convergence is to be achieved. The overall results indicate that the proposed method has the capability of handling various pipe networks problems without changing in model or mathematical formulation. Application of SCE in optimization model can lead to accurate solutions in pipes with zero flows. Finally, it can be concluded that the proposed method is a suitable alternative optimizer challenging other methods especially in terms of accuracy.
This paper is devoted to the study of the peristaltic motion of non-Newtonian fluid with heat and mass transfer through a porous medium in the channel under the effect of magnetic field. A modified Casson non-Newtonian constitutive model is employed for the transport fluid. A perturbation series’ method of solution of the stream function is discussed. The effects of various parameters of interest such as the magnetic parameter, Casson parameter, and permeability parameter on the velocity, pressure rise, temperature, and concentration are discussed and illustrated graphically through a set of figures.
Stability of thermal convection in an infinitely long vertical channel in the presence of a uniform horizontal magnetic field applied in the direction parallel to the hot and cold walls was numerically studied. First, in order to confirm accuracy of the present numerical code, the one-dimensional computations without the effect of magnetic field were computed and they agreed with a previous study quantitatively for various values of the Prandtl number. Then, linear stability analysis for the thermal convection flow in a square horizontal cross section under the magnetic field was carried out for the case of Pr = 0.025. The thermal convection flow was once destabilized at certain low Hartmann numbers, and it was stabilized at high Hartmann numbers.
The paper presents a numerical investigation of non-Newtonian modeling effects on unsteady periodic flows in a two-dimensional (2D) pipe with two idealized stenoses of 75% and 50% degrees, respectively. The governing Navier-Stokes equations have been modified using the Cartesian curvilinear coordinates to handle complex geometries. The investigation has been carried out to characterize four different non-Newtonian constitutive equations of blood, namely, the (i) Carreau, (ii) Cross, (iii) Modified Casson, and (iv) Quemada models. The Newtonian model has also been analyzed to study the physics of fluid and the results are compared with the non-Newtonian viscosity models. The numerical results are represented in terms of streamwise velocity, pressure distribution, and wall shear stress (WSS) as well as the vorticity, streamlines, and vector plots indicating recirculation zones at the poststenotic region. The results of this study demonstrate a lower risk of thrombogenesis at the downstream of stenoses and inadequate blood supply to different organs of human body in the Newtonian model compared to the non-Newtonian ones.
