
The paper is focused on the evaluation of spruce wood (Picea abies L.) used in building construction using the new medium-scaled test method, which is a modification of the standard test method according to standard STN EN ISO 11925-2. The significance of the new medium-scale test method lies in its accessibility compared to standard test methods and in the ability to test samples of various dimensions (lengths up to 1 meter) at different angles of exposure to the heat source. The new medium-scale method is based on exposing the samples (300 & times; 100 & times; 100 mm) to a 1 kW flame source for 1800 s. The test setup was placed on the laboratory scale with thermocouples placed in the samples for the duration of the test. This enabled us to measure the mass loss, temperature courses, charred layer depth, and charring rate. With this method, the mentioned parameters were determined for three different angles of inclination (0 degrees, 45 degrees, 90 degrees) for the samples, which simulate the actual placement of a wooden building element in a structure. Values of mass loss ranged from 3.33 +/- 0.62% (0 degrees angle) to 4.66 +/- 0.33% (90 degrees angle). The temperature courses at the angles of inclination 90 degrees and 45 degrees were similar. Nevertheless, at the 90 degrees angle, the maximum temperature reached was 75.6 degrees C lower. The charring rate reached its maximum value of 0.49 mm & centerdot;min-1 at an inclination angle of 45 degrees. The results showed the influence of the angle of inclination and wood grain directions on fire characteristics.
Under changing climate conditions in the Russian Federation, the four-eyed fir bark beetle (Polygraphus proximus Blandf.) is causing widespread mortality of Siberian fir (Abies sibirica Ledeb.) stands. Due to the scale of mortality and the patchy nature of damage to the stands, dead stands remain in a stable state for extended periods. This raises the question of the feasibility of industrial use of deadwood, given the time since stand death. This study examined changes in the physical and mechanical properties of A. sibirica wood across different periods after tree death. The study revealed that in the first 3-5 years after their death, dead trees experience a sharp decrease in the impact strength of wood, while most of the physical and mechanical properties of stem wood remain at levels similar to those of standing trees for decades. It is caused by the reduced moisture content of deadwood, which falls below 20%, making it unsuitable for the development of wood-destroying fungi. Intensive wood decay is observed only at the base of the stem. Also, as the time since death increases, dead trees are selected based on their physical and mechanical properties. By 20 years of death, remaining trees in the stand have wood density and strength values above the average for A. sibirica. Based on the data obtained, stem wood from dead trees could be a valuable raw material for a wide range of wood processing industries.
Coniferous forests are drying out due to climate change, creating a need for alternative species. Grey poplars (Populus & times; canescens) are underutilized in Hungary, with about 12 million m3 reaching harvesting age by the end of 2026 and decaying due to limited industrial use. The bondability of grey poplar with structural polyurethane (PUR) and nonstructural polyvinyl acetate (PVAc) adhesives, comparing it with Scots pine (Pinus sylvestris) and beech (Fagus sylvatica) under both dry and wet conditions, in accordance with EN standards is evaluated in the study. Beech met the minimum dry tensile shear strength requirements for both adhesives, whereas grey poplar and Scots pine did not. Grey poplar bonded with PVAc showed higher dry strength than Scots pine, while Scots pine with PUR outperformed grey poplar. Despite its higher density, grey poplar heartwood exhibited lower strength than sapwood. Overall, grey poplar's adhesive performance was comparable to Scots pine, suggesting it could serve as a viable alternative to coniferous species in both load-bearing and non-load-bearing applications.
The study focuses on current trends and innovations in product packaging that reflect consumers' growing emphasis on sustainability and eco-friendly materials. This study, based on a literature review and secondary analysis of a questionnaire survey of a sample of Slovak respondents, examines consumer preferences, attitudes toward packaging materials, and motivations for recycling or reuse. The results show that paper and paper packaging are perceived as the most eco-friendly materials, with consumers appreciating their biodegradability, recyclability, and health safety. Nevertheless, the environmental parameters of packaging are only taken into account to a limited extent in purchasing decisions, and the willingness to pay more for environmentally friendly solutions remains rather moderate. The analysis also shows that generational differences were not statistically significant in most cases, except for a preference for paper packaging, which was strongest among older respondents. The study concludes by presenting examples of innovative paper-based packaging and suggests the direction of future developments in sustainable packaging materials.
A comparative analysis of the surface roughness of false heartwood and sapwood zones of beech wood (Fagus sylvatica L.) after thermal treatment by steaming, followed by CNC milling, is presented in the paper. The samples were treated in four steaming modes (95 degrees C, 115 degrees C, 125 degrees C, and 135 degrees C) simulating industrial conditions. The milled surfaces were evaluated using the roughness parameters Ra and Rz using a Keyence VHX-7000 digital microscope. The results show that thermal treatment reduces surface roughness in both zones, with the most significant improvement observed at medium temperatures (115-125 degrees C). The false heartwood zone consistently exhibited lower roughness values, indicating a denser, more stable structure during milling. Statistical analysis confirmed the significant influence of the treatment mode and wood zone on surface roughness. These findings provide guidance on optimizing heat-treated beech machining parameters, thereby increasing efficiency in furniture production.