• 学术搜索
  • 科研智能体
    • Research Labs
    • AI 阅读
    • AI 文库
    • 深度研究
    • 学者亮点
  • 学术资源
    • AI2000
    • 期刊/会议
    • 学者库
    • 学术API
      MCP&Skill
    • 溯源树
    • 数据集
  • 知识沉淀
    • 学术空间
订阅小程序
旧版功能
aminer vip
开通会员低至0.73元/天
一次搞定AI科研
立即登录
  • English
  • 联系方式
    Indian journal of cryogenics

    Indian journal of cryogenics

    JournalISSN 0379-0479

    年发文量

    研究主题

    论文(417)

    排序
    1Development and Testing of Novel Hybrid CICC Joint
    Piyush Raj,Arun Panchal, Anees Bano, Nitish Kumar, Hemang Agravat, Mahesh Ghate, Arvind Tomar, Yogendra Singh, Pankaj Varmora, Bhadresh Parghi,Deven Kanabar, Azad Makwana,

    The electrical joints are very important parts for any kind of superconducting magnet like solenoid magnet, hybrid magnet and superconducting bus-bar etc. Joints preparation is very crucial for superconducting magnets because of the local heating from resistive losses can drive the superconductor into unstable condition of the magnet and as a result the superconducting magnet get premature quench. In this paper a joint has been developed in shake-hand type. The joint has been made by using the two different type of cable in conduit conductor (CICC) i.e. Nb3Sn and NbTi CICC. The 15×15 mm2 Nb3Sn and 14.8×14.8 mm2 NbTi CICCs of length ~ 200 mm have been used for preparing superconducting joint. The joint length is approximately 110 mm and enclosed with copper jacket. Lead-Tin (Pb 60% & Tin 40%) solder material having melting point 188º C, is used for the preparation of the joint. The four probe method was used for the joint resistance measurement. The measured joint resistance is ~2 n?. The main aim of this type of joint fabrication is the testing of Nb3Sn based CICC solenoid magnets. In this paper we have discussed the joint fabrication procedure, & its electrical characterization with different wattage of heating pulse near liquid helium (LHe) temperature.

    2025
    引用
    AI阅读
    加入学术空间
    2Mixed Refrigerant Joule-Thomson (MRJT) Cryocooler for Medical Applications
    Darshit Parmar, M. D. Atrey

    Mixed Refrigerant Joule-Thomson (MRJT) cryocooler have shown great potential for cooling temperature above 80 K after the introduction of refrigerant mixtures in JT cryocoolers. These make them suitable for various medical cooling applications, where biological samples are to be stored below -80 °C. MRJT cryocoolers use conventional refrigeration and air conditioning components and have no moving parts at the cold end making them simple compared to other cryocoolers. At temperature above 150 K, MRJT cryocoolers are a great alternative to Stirling and Pulse Tube cryocooler due to their simplicity and cost effectiveness. In the present work, keeping in mind the medical industry, MRJT cryocooler for -100 °C and -130 °C applications are developed. The working fluid is a refrigerant mixture consisting of common hydrocarbons in an optimized proportion. Based on the studies, it is found that a no load temperatures of -110 °C and -133 °C are obtained using two different refrigerant mixtures, Mix 1 and Mix 2. In addition to this, cooling effect of 50 W is obtained at -100 °C and -130 °C using refrigerants Mix 1 and Mix 2 respectively. Furthermore, by increasing the charging pressure of Mix 1, no load temperature reduced to -120 °C while 50 W of cooling effect was obtained at -107 °C.

    2025
    引用
    AI阅读
    加入学术空间
    3Transient Heat Transfer Analysis of Low-Temperature Packed-Bed for Cryogenic Energy Storage System
    Debashis Mohanty, Rohan Dutta

    The roundtrip-efficiency of a typical Cryogenic Energy Storage system can be increased from the existing 50-55% to as high as 85% and higher by using appropriate storage of heat of compression and low-temperature refrigeration. There are few options for storing low-temperature refrigeration at around 80 K and higher. One of them is to store this refrigeration using pebbles of granite or similar materials in a packed-bed. Similar systems have been studied earlier; however, few studies have investigated the heat transfer inside the bed for optimisation. In this work, we have attempted to develop an appropriate model to capture the heat transfer in that porous medium. The model has been adapted from the literature, modified to include variations in thermo-physical properties at such low temperatures, and converted from a one-dimensional model to a polar coordinate system to capture radial heat transfer along the bed. The model was validated using experimental data.

    2025
    引用
    AI阅读
    加入学术空间
    4Prospects for Improving the Technology Readiness Level of Cryogenic Carbon Capture
    Emel V Kurian,Pavitra Sandilya

    Carbon capture, utilization, sequestration, storage and transport (CCUSST) has been adopted to mitigate climate change caused by global warming. Cryogenic carbon capture (CCC) has been shown to give high CO2 recovery rate, without any additives, and moreover, it can achieve both capture and sequestration of CO2. CCC has been found to be the most economical in handling feed gas with high CO2 concentration (>80%). However, there is a general reservation regarding the cost of adapting CCC since the process involves refrigeration for CO2 separation. To overcome this reluctance towards adaptation of CCC, we need to benchmark this method against the popular and mature non-CCC techniques. In this work, we have reviewed different CC techniques with their technology readiness level (TRL) to assess the factors that impedes their commercial acceptance. We have analyzed the challenges of implementing CCC in light of the cost of capture, technological challenges, and policies.

    2025引用:1
    引用
    AI阅读
    加入学术空间
    5Numerical and Experimental Investigation of Bowing in Large Diameter Liquid Oxygen Feed Lines
    S Vivek, R Vinayaravi, R Vasudevan, Suresh Mathew Thomas

    The Indian Space Research Organisation (ISRO) is developing a semi-cryogenic engine with a thrust of 2000 kN. Due to the engine’s high thrust, the required Liquid Oxygen (LOX) flow rates are substantial, necessitating the use of 290 mm diameter pipelines to convey LOX from the test facility to the engine. During the initial chill-down phase, the large diameter of the pipeline can lead to significant temperature gradients across the circumference, potentially resulting in thermal bowing, which poses concerns such as, pipeline bending and increased loads on the supports. To address this, detailed non-linear finite element simulations were conducted to predict the structural behavior of the feed lines. An acceptable thermal gradient was identified, ensuring that the stresses caused by thermal bowing remained within safe limits. Novel techniques were implemented to maintain these gradients during the chilling process. During the first chill-down test of the system, multiple temperature and displacement measurements were employed. All necessary conditions for engine start were met in the very first attempt, and thermal bowing remained well within acceptable limits. This paper presents both the numerical simulations and experimental results.

    2025
    引用
    AI阅读
    加入学术空间
    立即登录,查看全部 417 篇论文

    高被引作者

    作者引用发文
    Subrata Pradhan19516
    Biswanath Sarkar18417
    Mohananand M. Jadhav14017
    Anindya Chakravarty13023
    rajendran s menon12617
    mukesh goyal12323
    H Vaghela11514
    Pradhan Jedidiah11511
    N Shah11513
    V.L. Tanna9913

    高产作者

    作者引用发文
    Milind Atrey6225
    Anindya Chakravarty13023
    mukesh goyal12323
    Parthasarathi Ghosh7119
    Mohananand M. Jadhav14017
    rajendran s menon12617
    Biswanath Sarkar18417
    Subrata Pradhan19516
    Soumen Kar1116
    Tripti Sekhar Datta3315

    相关期刊

    Journal of fluids engineering
    Journal of thermophysics and heat transfer
    Experimental Thermal and Fluid Science
    Thermophysics and Aeromechanics
    Progress in Computational Fluid Dynamics
    Multiphase Science and Technology
    Journal of Fluids Engineering-transactions of The Asme
    Journal of Heat Transfer-transactions of The Asme
    Journal of Turbomachinery-transactions of The Asme
    INTERNATIONAL JOURNAL of TURBOMACHINERY PROPULSION and POWER