
Silicon (Si)-based full cells maintain stable cycling at elevated temperatures yet exhibit a sudden capacity fade at room temperature. This temperature-dependent behavior is specific to Si-based full cells and cannot be explained by conventional graphite-based degradation models. This study identifies the origin of the fade mechanism as a Si-intrinsic, kinetics-driven degradation process and proposes a corresponding mitigation strategy. Electrochemical and post-mortem analyses show that intrinsically sluggish Si kinetics at 25 degrees C induce a large overpotential that drives lithium plating and accelerates surface degradation. Guided by this understanding, a formation strategy is introduced to suppress lithium plating onset, which is shown to prevent sudden capacity fade and improve capacity retention from 38% to 85% in NCM/Si cells and from 55% to 93% in NCM/Si-Gr cells. By elucidating the kinetic origin of the sudden capacity fade and establishing formation engineering as an effective and scalable control strategy, this work addresses key challenges in the practical implementation of high-energy Si-based lithium-ion batteries. (c) 2026 Science Press and Dalian Institute of Chemical Physics, Chinese Academy of Sciences. Published by Elsevier B.V. and Science Press. All rights are reserved, including those for text and data mining, AI training, and similar technologies.
The sustainable recycling and regeneration of spent lithium iron phosphate (LiFePO4, LFP) cathodes is crucial for minimizing resource waste and enabling circular utilization of long-life lithium-ion battery materials. However, most existing recycling strategies primarily emphasize elemental recovery and largely neglect the intrinsic degradation mechanisms that control performance decay in retired LFP cathodes, leading to regenerated products with limited electrochemical performance. Performance deterioration in spent LFP is strongly linked to the accumulation of Fe-Li antisite defects and interfacial instability during extended cycling, which obstruct lithium-ion diffusion pathways, accelerate active lithium loss, and cause kinetic degradation. In this work, a rapid upgrading regeneration strategy based on ultrafast Joule heating is proposed to directly target defect repair and interface reconstruction in spent LFP cathodes. The applied thermal shock efficiently heals Fe-Li antisite defects within the bulk lattice, restoring lithium-ion transport while suppressing excessive phase decomposition. Meanwhile, a composite surface architecture is formed, consisting of a LiF-rich interfacial layer and an outer nitrogen-doped carbon coating, which cooperatively enhances interfacial lithium-ion transport, electronic conductivity, and structural stability during cycling. Density functional theory calculations reveal evident charge redistribution across the reconstructed interface, together with a reduced electronic bandgap and stabilized lattice structure, indicating strong electronic coupling between the surface layers and the LFP bulk. Electrochemical evaluations demonstrate decreased polarization, faster reaction kinetics, and markedly improved cycling stability compared with spent and commercial cathodes. Beyond material restoration, this work establishes a defect-directed regeneration paradigm that links degradation mechanisms with functional upgrading, providing a general strategy for high-value recycling and sustainable reuse of lithium-ion battery cathode materials.
Enhancing perovskite solar cell (PSC) performance often requires light management, interface engineering, and crystallization control, but these approaches typically involve multiple functional additives or interfacial modifiers, increasing fabrication complexity. Here, we introduce a polymer-assisted interfacial engineering strategy using a carboxymethyl chitosan (CMC)-based polymer functionalized with Cs* (PCM-Cs* ) to modify mesoporous TiO2 (mp-TiO2). Upon heating, this polymer sequentially releases functional molecular species, inducing backbone rearrangement, deacetylation, and polysaccharide cleavage. The resulting fragments passivate defects, promote TiO2 microstructural reconstruction, and enhance electronic coupling with the perovskite. These effects yield power conversion efficiencies of 25.5% and 26.04% with TiO 2 and SnO2 electron transport layers, respectively. To the best of our knowledge, this represents a record efficiency for fully air-fabricated perovskite solar cells. The devices also demonstrate outstanding stability under various ISOS proto-cools, with unencapsulated mp-TiO2:PCM-Cs* cells retaining over 97% of their initial PCE after 2,750 h dark shelf storage, projecting an estimated T80 of similar to 20,000 h. This work provides a universal and scalable interfacial engineering strategy to simultaneously achieve high efficiency and long-term stability in air-processed perovskite solar cells with simplified fabrication. (c) 2026 Science Press and Dalian Institute of Chemical Physics, Chinese Academy of Sciences. Published by Elsevier B.V. and Science Press. All rights are reserved, including those for text and data mining, AI training, and similar technologies.
Photocatalytic CO2 reduction in gas-solid systems is a complex process that requires the integrated consideration of illumination, photocatalytic performance, and gas diffusion on the catalyst surface. Oversimplification of these factors in existing computational fluid dynamics models severely compromises their predictive capability under realistic reaction conditions. To address this limitation, this study develops a multi-mechanism kinetic model that integrates photoexcitation, Arrhenius thermal activation, Langmuir adsorption saturation, and Thiele diffusion resistance within a unified kinetic expression. Model parameters were constrained and validated using a combination of first-principles calculations and multiscale optical, spectroscopic, adsorption, and transport measurements in a tree-shaped uniform-flow reactor. Photocatalytic experiments of four distinct catalysts are then used to validate the multi-mechanism kinetic model, with R2 above 0.98. Under model-derived conditions, the operation of the tree-shaped reactor achieve an optimal conversion rate of 116.7 lmol g-1 h-1. The model reliably predicts the experimental rates across a wide range of operating conditions. It also accurately captures the optimal space velocity range and the promotional effect of increasing temperature. This work offers a generalizable framework for the theoretical understanding, modelling, and scale-up of photocatalytic CO2 conversion systems. (c) 2026 The Authors. Published by Published by Elsevier B.V. and Science Press on behalf of Science Press and Dalian Institute of Chemical Physics, Chinese Academy of Sciences. This is an open access article under the CC BY license (http://creativecommons.org/licenses/by/4.0/).
The electrocatalytic reduction reaction of CO2 (CO2RR) has been extensively studied, including on single-atom catalysts (SACs). However, a precise mechanistic understanding of the factors governing electron-transfer processes and Faradaic efficiency (FE) in SACs remains limited. Most established correlations address isolated aspects, such as activity or selectivity, without investigating their dependence on the critical parameter of current density. The mechanistic interpretation should elucidate all these aspects simultaneously within a well-defined series of electrocatalysts. In this series, only the electronic properties of the SAC are tuned, while all other factors should remain unchanged. We report here a well-defined series of FeN4-type SACs tailored with a fifth axial ligand, introduced via coordinatively assisted materials-surface engineering. By combining precise synthesis and extensive characterization, we have demonstrated that this series of electrocatalysts offers unique opportunities to understand these aspects. The electrocatalytic behavior of these SACFe electrocatalysts for CO2-to-CO conversion exhibits distinct trends in activity and FE with current density. In-depth computational modeling shows that these trends cannot be explained solely by the influence of the iron electronic structure and oxidation/spin state on the adsorption of key intermediates (*COOH, *CO, and *H), but rather by their effect on the ability of the metal center to accumulate and transfer charge to CO2 under operating conditions, with a clear dependence on charge localization (Bader charge). Controlled tuning of the iron electronic environment, therefore, provides a direct means to modulate charge redistribution and, consequently, catalytic performance. The structural control offered by this series is a distinctive advantage, enabling robust mechanistic insights.