• 学术搜索
  • 科研智能体
    • Research Labs
    • AI 阅读
    • AI 文库
    • 深度研究
    • 学者亮点
  • 学术资源
    • AI2000
    • 期刊/会议
    • 学者库
    • 学术API
      MCP&Skill
    • 溯源树
    • 数据集
  • 知识沉淀
    • 学术空间
订阅小程序
旧版功能
aminer vip
开通会员低至0.73元/天
一次搞定AI科研
立即登录
  • English
  • 联系方式
    Journal of the Ceramic Association, Japan

    Journal of the Ceramic Association, Japan

    JournalISSN 1884-2127

    年发文量

    研究主题

    论文(3278)

    排序
    1Prediction of Thermal Conductivity of Ceramic Fibrous Insulator
    K HAYASHI, H OHKAWA, T NISHIKAWA

    The thermal conductivity of alumino-silicate fibrous insulators with various bulk densities was measured by the transient hot wire method under various reduced pressures in order to propose a simple equation for predicting their thermal conductivities. The results obtained were summarized as follows:(1) The thermal conductivity of ceramic fibrous insulators with various bulk densities decreased gradually with decreasing pressure ranging from 760 to 10mmHg and converged to an extremely low constant value under 10-2mmHg after a sharp decrease between 10 and 10-1mmHg, due to the pressure dependence of thermal conductivity of air. Their thermal conductivity increased with increasing bulk density all over the pressure range covered in the thermal conductivity measurement.(2) The thermal conductivity of ceramic fibrous insulators in helium, oxygen and freon-12 gas atmospheres also increased with an increase in bulk density, and their thermal conductivity in a gas atmosphere having high thermal conductivity such as helium was higher than those in gases with lower thermal conductivity such as freon-12.(3) In alumino-silicate fibrous insulators, the following experimental relation among λ (thermal conductivity of insulator), λs (that of fiber: 1.07W/m·K), λf (that of gas being filled between fibers) and φ (volume fraction of fiber) was obtained.λ=aλs+bλf+(1-a-b)λsλf/(1-y)λs+yλfa=0.169φ1.57b=(1-φ)1.16y=0.81-0.043lnφThis equation enabled us to calculate the thermal conductivity of the fibrous insulators in various gas atmospheres (-0.2W/m·K) at room temperature within the error of about ±10%.

    1987
    引用
    AI阅读
    加入学术空间
    2Formation and Color of Spinel Solid Solution in Li2O-MO-TiO2 (m=mg, Co, Ni) System
    Tadahiko SAITO,Norio MOCHIDA,Atsushi OHTSUKA
    1987
    引用
    AI阅读
    加入学术空间
    3Preparation of Sialon Powder from Mixture of SiO2 and Al2O3⋅2H2O by Thermal Carbon Reduction
    Hideyuki YOSHIMATSU,Tatsumi YABUKI, Hisashi MIHASHI
    1987引用:1
    引用
    AI阅读
    加入学术空间
    4Microstructural Change of Polycrystalline Ba-Ferrite (bao·6fe2o3) by Hot-Extrusion Processing
    T NISHIKAWA,T NISHIDA, T SHIONO,I UENO, H SANO

    To improve the damage evaluation methods in the design code for Fast Breeder Reactors (FBRs), a series of creep—fatigue tests of structural models under thermal transient loadings are going on at Oarai Engineering Center of the Power Reactor and Nuclear Fuel Development Corporation (PNC). Test models are designed to incorporate representative structures of components and pipings used in FBRs and are subjected to severer cyclic thermal transients than those experienced in FBRs. The test is planned to be continued until failure occurs. This paper describes the creep—fatigue test results and their damage evaluation for the first test model.A 40 mm thick vessel model made of SUS304 austenitic stainless steel was subjected to cyclic thermal transients, in which sodium at 600°C and 250°C flowed repeatedly. The period of each transient was 2 h. Cracks were observed at seven test portions in the model after 1002 cycles of the thermal transients.Elastic and inelastic analyses were performed to evaluate creep—fatigue damage and crack propagation. The safety margins included in the creep—fatigue design methods based on elastic analysis as well as those based on inelastic analysis are discussed. Finally fracture mechanics analyses were performed to explain the observed crack growth.

    1987
    引用
    AI阅读
    加入学术空间
    5Preparation of Ultrafine Sic Powders by Pyrolysis of Tetramethyldisilane
    M ENDO, T SANO, K MORI,N URASATO,M SHIRAISHI

    Ultrafine silicon carbide powders of high purity have been prepared by pyrolysis of tetramethyldisilane at temperatures 700° to 1400°C. The diameter of the particles changed from 5 to 200nm depending on the pyrolysis conditions. The ultrafine particles consist of small crystallites of β-type SiC, arranged randomly in the particles. The molar ratio (C/Si) of the powders can be also controlled within the range 0.9 to 1.2 by pyrolysis conditions such as pyrolysic temperature and reactant concentration. No admixtures of carbon such as carbon soot or film on the SiC particles were observed with a high-resolution electronmicroscope even in the powders having (C/Si) ratio more than 1.0. The formation mechanism of the ultraf ine SiC powders is discussed in relation to the structure.

    1987引用:15
    引用
    AI阅读
    加入学术空间
    立即登录,查看全部 3278 篇论文

    高被引作者

    作者引用发文
    Sumio Sakka60242
    Hiroshige Suzuki57455
    Kenya Hamano54658
    Hiroaki Yanagida54251
    Mamoru Mitomo49829
    Takafumi Kanazawa46726
    Yoshizo Inomata41845
    toshiyoshi yamauchi40471
    Masayuki Nogami35010
    Renichi Kondo33737

    高产作者

    作者引用发文
    toshiyoshi yamauchi40471
    Kenya Hamano54658
    Hiroshige Suzuki57455
    Hajime Saito32555
    Megumi TASHIRO27354
    yoichi shiraki25352
    Hiroaki Yanagida54251
    Shigeyuki Somiya29750
    Yoshizo Inomata41845
    Goro Yamaguchi30844

    相关期刊

    暂无数据
    暂无数据