
As the construction of large-scale industrial complexes progresses, the need for MSE walls, such as large-scale cut or high fill, is gradually increasing, often being designed and constructed in multi-tiered forms. However, Korea design standards(KDS) largely rely on foreign criteria. This paper analyzes and discusses the design, construction, and numerical analysis of multi-tiered MSE walls in Korea, comparing domestic and international design standards and methods. The study indicates that a part of the domestic design standards requires improvement. The failure of high fill multi-tiered MSE walls follows a bi-linear pattern that passes through the active wedge failure within the backfill and directly beneath the reinforced soil, necessitating stability evaluation of planar compound sliding. It was found that for high embankments where deformation occurs due to fill, the safety factors derived from strength reduction analysis and limit equilibrium analysis differ. In finite element and limit equilibrium analysis of MSE walls with geosynthetics, the interface factor between the reinforcement and soil should apply the contact friction angle rather than the pullout angle. Additionally, the stability of compound sliding and the sliding pattern between extensible and non-extensible reinforcements in multi-tiered MSE walls differs, indicating a need for research on the limit height of walls, design methods, and related safety factors based on the type of reinforcement.
The aging of critical social infrastructure, including bridges, is a growing concern worldwide, necessitating long-term structural health monitoring and safety management. While conventional methods utilizing contact-based sensors or unmanned aerial vehicles (drones) offer high accuracy, their widespread application is hindered by challenges such as high installation and maintenance costs, limitations to localized measurements, and constraints on long-term operation. To overcome these limitations, this study proposes a novel displacement monitoring methodology that leverages widely available CCTV infrastructure. The proposed technique extracts features from CCTV footage based on Digital Image Correlation (DIC) and converts them into time-series data. Subsequently, deep learning models such as Long Short-Term Memory (LSTM) and Gated Recurrent Unit (GRU) are applied to estimate the micro-displacements of the bridge. The performance of the proposed methodology was validated using video footage acquired from an actual bridge. The results confirmed a very low error, with a Root Mean Square Error (RMSE) of 0.1116mm, when compared to the actual displacement data measured by contact-based displacement sensors. This research holds significant academic and practical value as it complements the technical and economic shortcomings of existing monitoring methods and presents a new direction for proactively utilizing CCTV infrastructure, an already established societal asset, for bridge safety management.
This study was conducted to evaluate the practical applicability of an early warning sensor system for net-type check dams. A strain gauge was installed on the wire ropes of the net structure at the Umyeonsan check dam site, enabling real-time measurement of micro-displacements caused by debris-flow impacts. A monitoring system was established to transmit the measured data to a management server through an IoT-based communication network. Tensile tests were performed to verify the accuracy and reliability of the sensor, and field application results showed that even minor impacts were clearly detected, demonstrating the feasibility of real-time impact load monitoring. Based on the measured displacement and load data, the applicability of a multi-level warning system was examined, indicating that the proposed approach can enhance integrated response capabilities compared to conventional systems where protective structures and warning functions operate separately. This study provides fundamental data for introducing an early warning function to net-type check dams and is expected to contribute to improving initial response to debris-flow events.
This study aims to evaluate the impact mitigation performance of net structures applied to debris-flow protection facilities, as debris-flow damages have increased due to recent episodes of extreme rainfall and the demand for protective facilities has consequently grown. Tensile tests were conducted on 16-mm-diameter, 2.0m long wire ropes, comparing the energy absorption capacity of conventional wire ropes with that of buffer-type wire ropes combined with extension springs (spring diameter: 15mm, spring constant: 69.4kN/m). In addition, free-fall numerical simulations were performed using the Abaqus program to analyze the impact response of conventional nets and shock-absorbing nets. The tensile test results indicate that the buffer-type wire rope exhibits approximately 1.76times higher energy absorption per unit length than the conventional wire rope. The numerical analysis further revealed that, under identical impact conditions, the maximum tensile force acting on the shock-absorbing net was reduced to about 25% of that of the conventional net, while the impact duration increased by approximately 60%. Therefore, the shock-absorbing net is considered a more effective and safer alternative for debris-flow protection facilities compared to conventional net systems.
This study presents a predictive model to estimate the productivity of excavator-mounted vibratory rippers as a function of rock strength, with the aim of improving their field applicability. Previous research on ripper productivity has predominantly focused on bulldozer-mounted rippers, while academic studies on excavator-mounted vibratory rippers remain scarce. To address this research gap, data provided by overseas manufacturers and field test results in this study were utilized to analyze the quantitative relationship between uniaxial compressive strength (UCS) of rock and the corresponding production rate. Various machine learning algorithms were compared, and the Gamma regression model was found to most effectively represent the exponential decrease characteristics associated with increasing rock strength. Furthermore, empirical equations originally developed for impact hammers were extended to derive RQD-based productivity curves, enabling the proposed model to be applied even at sites where RQD data are not available. Although the dataset used in this study is limited and may restrict generalization, the proposed approach provides a quantitative foundation for evaluating and predicting the productivity of backhoe-mounted vibratory rippers. Future work will focus on improving model reliability and prediction accuracy through the integration of additional domestic field data.