
Indonesia is the largest country in Southeast Asia, consisting of more than 17,000 islands and a coastline of approximately 81,000 kilometers, with over half of its territory covered by water. To optimize this vast marine potential for public welfare, comprehensive data collection and mapping are essential. The oil and gas sector remains a key contributor to national revenue. For instance, Pertamina Hulu East Kalimantan (PHKT) exceeded its 2023 production target, achieving around 9,900 barrels of oil and 45 million cubic feet of gas per day. To support offshore operations, a Platform Supply Vessel (PSV) prototype named Bramantya was designed. This study analyzes the vessel using Computational Fluid Dynamics (CFD) to determine the optimal hull form for operational performance and fuel efficiency. Three hull variations were examined: a conventional hull, a hull with additional chines, and a wide-bow hull. The simulation was validated against previous experimental studies, showing consistent linear results with an average error of 4.25%. Simulations at Froude numbers 0.2–0.6 show that the wide downward-bowed hull reduces drag by 7.69% compared to the conventional hull, thereby improving fuel efficiency.
Gravitational water vortex turbines are environmentally friendly power generation systems that convert the energy of vortex water flow into mechanical energy using turbine runners. This study aims to analyze the effect of a two-stage configuration with varied radial runner positions and water discharge on turbine performance. Experiments were conducted using a low-speed water channel with a conical basin to generate vortex flow. Savonius-type runners were installed vertically in two stages with radial positions of 0.5, 0.6, and 0.7 relative to the basin radius. Each configuration was tested at several water discharge rates. The primary parameter measured was mechanical power output, which was obtained using torque sensors and rotational speed meters to provide precise data. Results showed that the radial position 0.5 produced the best performance, generating 12.28 watts in the first and 16.68 watts in the second. Runner position and water discharge directly influenced vortex stability and energy conversion efficiency. The two-stage configuration with optimal runner placement significantly improved system efficiency. These findings suggest that the two-stage vortex turbine design is promising for small-scale power generation in remote areas.
Structural steel corrosion is a critical engineering problem that can lead to catastrophic failures, resulting in loss of life, environmental harm, and substantial economic damage. Notable incidents, such as offshore platform collapses and ship hull breaches, have demonstrated the severe consequences of undetected or underestimated corrosion. In marine environments, crevice corrosion presents a particularly challenging case, as confined chemical conditions and the presence of barnacles promote localized degradation. Barnacles generate microcracks that accelerate the deterioration process. However, finite element modeling of crevice corrosion remains scarce and often relies on oversimplified geometries, which limits the accuracy in capturing actual corrosion volume, depth, and affected area. This study develops a 3D finite element model of barnacle-induced crevice corrosion on 316L stainless steel plates, based on long-term immersion data. Corrosion geometries were analyzed using laser scanning microscopy, with the analytical mapped field feature applied under transverse loading and random pit positions for exposure durations of 6, 12, and 36 months. The results reveal progressive increases in displacement (up to 17.27%), strain (30.8%), and stress (20.12%) compared to uncorroded plates, underscoring the substantial impact of localized corrosion on structural performance.
Floating structures are key components in offshore renewable energy systems. In the development of energy conversion, several integrated components are required, one of which is the Cold-Water Pipe (CWP). This integration will affect the interaction of the structure with environmental loads such as waves and currents, which influence the stability and seakeeping of the structure. This study employs computational analysis based on the Boundary Element Method (BEM) to more efficiently evaluate the hydrodynamic response of full-scale structures. Response Amplitude Operator (RAO), additional mass, motion response, and mooring line tension are identified as the main parameters. It was found that all these parameters are sensitive to mesh discretization. A mesh convergence study was conducted using mesh sizes of 1.8, 2.1, 2.2, and 2.3 m, which produced consistent RAO and additional mass values. Conversely, mesh sizes of 1.9, 2.0, 2.4, and 2.5 m showed inconsistencies in stability results at sea. The coarsest net (2.5 m) produced errors of up to 33% in swing, heave, and roll motions, with greater deviations in heave motion. However, tension on the mooring line remained relatively stable, indicating reduced sensitivity to variations in net size.
The development of Vertical Axis Wind Turbines (VAWTs) has become a key focus in renewable energy utilization due to their ability to operate at low wind speeds and their simple design. This study aims to analyze the effects of inlet velocity variations and fluid physical properties on flow patterns, turbulence, and kinetic energy in VAWTs. The simulation was conducted using the Computational Fluid Dynamics (CFD) method, based on ANSYS Fluent, for a 2D turbine model with a diameter of 12 cm. Inlet velocity variations of 10, 11, 12, 13, and 14 m/s were tested using three types of fluids: air, helium, and hydrogen. The results show that increasing inlet velocity transforms the flow pattern from stable to complex, with greater turbulence forming behind the cylinder. Air exhibited the highest kinetic energy at low to medium velocities, ranging from 10 to 12 m/s, which was up to 24.7% higher than that of helium and 3.8% higher than that of hydrogen. At higher velocities, 13–14 m/s, the kinetic energy difference among the three fluids decreased to less than 1.5%. Furthermore, outlet velocity was consistently higher than inlet velocity for all fluids, with hydrogen achieving the highest acceleration at 14 m/s.