
Moulds are critical components governing both thermal transfer and shape formation in glass container manufacture. This study employs finite element analysis to characterise temperature and stress fields in blow moulding moulds during processing. Results reveal a well-defined thermal gradient across the mould structure, with maximum temperatures at the inner cavity surface decreasing progressively outward. This thermal distribution correlates strongly with the mould's geometric design and wall thickness profile. Thermal analysis reveals significant stress localisation, particularly in the neck region, arising from the interplay of geometric constraints, wall thickness variations and thermal conditions. While quantitative results remain specific to the investigated configurations, the established relationships between these factors provide valuable guidance for moulds operating under similar thermomechanical constraints. Systematic consideration of these coupled phenomena in mould design demonstrates practical value through improved blowing stability, enhanced product quality and extended tool life. This work offers analytical approaches and physical understanding to support mould optimisation in industrial glass-working practice.
A systematic investigation was conducted to evaluate the physical, microstructural and thermal properties of lithium aluminosilicate (LAS) glass-ceramics, with particular emphasis on the effect of MgO concentration on the coefficient of thermal expansion (CTE). Experimental results indicate that the glass to glass-ceramic transformation is accompanied by an approximately 3% volume shrinkage, resulting in an increased density of the glass-ceramic relative to the parent glass. X-ray diffraction analysis confirms the formation of (Li,Mg,Zn)1.7Al2O4Si6O12 as the main crystalline phase, which is isostructural with the-quartz solid solution (-QSS). Transmission electron microscopy reveals uniformly distributed nanocrystals with a mean size of-15 nm embedded within the residual glassy matrix. Thermal expansion measurements show that glass-ceramics containing higher MgO exhibit lower CTE values compared to that with lower MgO content, attributed to an increased fraction of the-QSS phase. Additionally, key thermal characteristic temperatures of the parent glass, including the softening point (TS), sphere (TSP), half-sphere (THSP), and onset of melting (TM), were determined using a high temperature heating stage microscope. Such parameters provide valuable insights into the thermal behaviour and processing window of LAS glass-ceramics.
Glass samples in the ternary NaPO3-MoO3-V2O5 system were prepared using the melt-quenching technique and structurally characterised by XRD, DSC, Raman and infrared spectroscopy. The system exhibited a wide glass-forming composition range, with observed Tg trends attributed to the formation of transition metal cluster structures and modifications in the phosphate network, leading to less connected Q1 and Q0 phosphate units within the glass matrix. Selected 70% transition metal-containing compositions were used to prepare their corresponding glass-ceramics. XRD analysis revealed the preferential crystallisation of vanadium-containing phases interconnected with phosphate tetrahedra, effectively replicating the local structural environment of their parent glass.
The colour coordinates on standard CIE 1931 chromaticity diagrams are presented for NCS (15 soda-15 lime-70 silica (mol%)) glasses, singly and doubly doped with the transition metals (Ti, V, Cr, Mn, Fe, Co, Ni and Cu) at low concentrations (<= 1 mol%) and with various rare earth dopants (Ce, Pr, Nd, Sm, Eu, Tb, Dy, Er, Ho). The colour coordinates were calculated from the transmission spectra in turn determined from measured glass absorption spectra. The colour coordinates of 232 glasses are reported, showing which colours can be made with common colouring dopants, and how their coordinates depend on: dopants, concentrations, sample thickness, melting conditions (oxidising electric furnace and reducing gas furnace) and concentrations of agents added to the batch as oxidising (NaNO3), reducing (C) and/or refining (Na2SO4) agents. Cu shows the greatest variability. The varying oxidation states of the dopants and their coordination are the main reasons for colour differences. The effect of the glass thickness in the colour appears because the absorption peaks can be very high and locate partly outside of the visible light range that changes the proportions of the spectrum that stimulate the three colour receptors in the eye.
The ability of bioactive glass/polymer and glass-ceramic/polymer composites to elicit bone bonding reactions, accompanied by degradability, when used as implants, without provoking adverse immune responses, makes them attractive biomaterials for bone regeneration. More efforts are being devoted to synthetic strategies to make the process cost-saving and more appealing for commercial production. Against this backdrop, we synthesised and studied the bioactivity of a bioactive glass-ceramic/polymer composite with the glass composition of SiO2-CaO-SrO-P2O5. A solution precipitation approach was used to obtain the bioactive-ceramic from sodium metasilicate (Na2SiO3.9H2O) as a low-cost silica alternative to alkoxysilane precursors, which was used afterwards as a filler phase in a starch-based matrix. An in vitro bioactivity experiment was conducted to determine the hydroxyapatite-inducing capacity of the samples in simulated body fluid for 7-14 days. Thereafter, the samples were characterised with scanning electron microscopy, energy dispersive x-ray analysis, x-ray diffractometry and Fourier transform infrared spectroscopy. Results obtained showed that the bioactive glass-ceramic composite exhibited superior morphological characteristics, higher bioactivity and degradability compared with the pristine sample. The strontium-based bioactive glass-ceramic/starch composite possesses promising characteristics that could make it a potential scaffold for bone regeneration. Hence, sodium metasilicate can be considered a viable and low-cost substitute for alkoxysilanes in the production of strontium-doped bioactive glass/polymer composites.