
During the fl ight, the parameters of the rocket as a control object change, since they depend on the trajectory point and fuel consumption. Th e indicators of the system for stabilizing its disturbed motion, in particular the stability margin and the requirements for the power of the executive device, are determined in a limited vicinity of individual trajectory points using algorithms developed for linear, stationary systems, which necessitates the introduction of safety factors in the hardware. In available sources, the development of methods for obtaining the above indicators that would not depend on the trajectory point is not given due attention. Th e work aims to develop methodological support for constructing an algorithm for controlling the disturbed motion of a rocket, when used in a certain trajectory section, the time-varying stabilization system becomes stationary, as a result of which the stability margin on the roots plane of the characteristic polynomial (ChP) and the requirements for the power of the actuator do not depend on the trajectory point. Th e mathematical model for controlling the rocket’s disturbed motion in one plane is formulated as a set of linear diff erential equations with variable parameters. In the vicinity of a certain trajectory point, these parameters are treated as constants, allowing the equation to be transformed according to Laplace, yielding transfer functions and analytical expressions for the ChP coeffi cients, which include the values of the model parameters of the control object predicted along the selected trajectory interval and the coeffi cients of the control law. Th is yields a system of algebraic equations, from which the dependence of the control law’s coeffi cients on the trajectory point is determined. Using the example of a time-varying rocket motion stabilization system, the possibility of obtaining those dynamic characteristics independent of the trajectory point, which are determined by the given location of the ChP roots on the complex plane, is shown
Th e infl uence of gravity was analyzed, and the morphological and functional responses of three moss species with diff erent gravisensitivity — Ceratodon purpureus (Hedw.) Brid., Physcomitrium patens (Hedw.) Mitt., Ptychostomum imbricatulum (Mhll. Hal.) Holyoak & N. Pedersen were determined depending on the phosphorus content (Pi) in the substrate. Phosphates (Pi) are important components in the initiation of gravitropism: low Pi content reduces the gravisensitivity of protonemata and growth reversion aft er clinorotation. At the same time, low Pi concentrations lead to morphological modifi cations, including stimulation of branching, an increase in moss turf density and size within the upper 0.2 cm layer of the substrate. It was determined that a 25 μM Pi concentration is the minimum test level used to substantiate the eff ect of gravistimulation on phosphate activity. Based on the variability of the values of gravitropic angles of the lateral protonemal branches depending on phosphate content, fi ve angle classes ranging from 0 to 90° were distinguished, with a dominant group of angles at 42...57°. A signifi cant eff ect of phosphates on the bending angle (gravisensitivity) of C. purpureus and P. imbricatulum was observed, whereas the eff ect on P. patens was insignifi cant. Th e eff ect of low phosphorus concentrations on the angle group 74...89° of P. patens branches, which grow almost parallel to the surface substrate, enhances plagiotropic growth. Plagiotropism in the turf structure of P. patens with perennial protonemata enables an increase in turf area within the upper substrate layer and expands access to nutrients from other locations. This indicates the species-specifi c features in growth correction of mosses under Pi defi ciency and the effi ciency of gravisensitivity in determining branch angle variation. Morphological modifi cations and dynamic changes in the gravitropic sensitivity of mosses under the infl uence of Pi are accompanied by physiological responses as a necessary condition for growth activity. Under phosphorus defi ciency, intracellular phosphatase activity in protonemal turfs increased, serving as a general indicator of metabolic status, and the stimulatory eff ect of phytohormones on phosphate metabolism was enhanced. It was determined that species-specifi c features of gravisensitivity in C. purpureus and P. patens may act as mediators of physiological processes during phosphate defi ciency and altered gravity. Th e variation in phosphatase activity is attributed to the ontogenetic characteristics of gametophyte developmental stages and the ecological association of mosses with specifi c substrates.
ASASSN-17hx is a remarkable hybrid nova that exhibited repeated rebrightenings accompanied by substantial spectral changes during its post-outburst evolution. In this study, we investigate its spectroscopic evolution using optical spectra obtained at the Shamakhy Astrophysical Observatory (ShAO) with the Shamakhy Fiber Echelle Spectrograph at a spectral resolution of (R = 28,000), together with spectra from the Astronomical Ring for Access to Spectroscopy (ARAS, R = 9,000...1,000) and the European Southern Observatory (ESO, R = 110,000). Th e observations analysed in this study cover the pre-maximum stage, the principal maximum, and two subsequent rebrightening episodes. Th e temporal behaviour of the Balmer, Fe II, He I, Na I D, Ca II H and K, and diff use interstellar band features was examined through measurements of line profi les, equivalent widths, and radial velocities. A detailed identifi cation of more than 250 spectral lines was carried out using the ShAO and high-resolution ESO spectra. Th e Balmer and Fe II lines exhibit pronounced multicomponent absorption structures whose radial velocities evolve throughout the rebrightening phase, indicating the presence of several expanding shells with diff erent kinematic properties. Th e He I 5876 and Na I D absorption features also show systematic variations that closely follow the photometric evolution of the nova. Th e high-resolution ESO spectra reveal seven distinct interstellar absorption components in the Na I D and Ca II H and K lines, providing constraints on the interstellar matter along the line of sight. Th e diff use interstellar band profi les measured in the ShAO and ESO spectra are in good agreement despite the substantial diff erence in spectral resolution. Th e absolute visual magnitude of the nova was estimated as MV = –7.56m, and its distance as approximately 4.5 kpc. Th e observed spectral evolution confi rms the hybrid nature of ASASSN-17hx and indicates that repeated mass-ejection episodes played an important role in shaping the complex velocity structure of the ejecta during the rebrightening stage. Th ese results provide new observational constraints on the physical conditions and kinematics of hybrid novae.
Low Earth orbits contain a large amount of space debris, motivating the development of technologies for its utilization and in-orbit processing. One promising approach involves transporting processed material between orbital locations using contactless propulsion systems. Th is paper presents a mathematical model of a two-body contactless orbital transfer system consisting of a spacecraft equipped with two coaxial, oppositely directed electric propulsion thrusters and a passive spherical body. Th e system enables orbital transfer by accelerating or decelerating the body via a directed jet. A method and computational algorithms are developed to evaluate both external and internal perturbing forces acting on the system, as well as the force exerted on the spherical body by the propulsion jet. Th e proposed approach is based on the numerical construction of a central projection of the body onto an auxiliary plane and requires signifi cantly less information about the target geometry — only the distance to the target and the angle of deviation of the target’s center of mass from the beam axis. Th is approach also enables force estimation under beam misalignment conditions. Special attention is given to cases of incomplete thrust transfer caused by deviation of the body from the jet axis. Th e developed algorithms account for variations in the applied force depending on the degree of misalignment. Th e results improve the accuracy of force modeling in contactless orbital transfer systems and can be used in the development of guidance and control algorithms.
Th e paper investigates the process of intensifying the fi nishing treatment of full-scale gas turbine engine compressor disks made of diffi cult-to-machine titanium (VT3-1, VT9) and heat-resistant (EI698-VD) alloys in an abrasive fl uidized bed (AFB). Th e problem of replacing labor-intensive manual operations with automated methods to ensure high fatigue strength and reliability of highly loaded complex-profi le parts is considered. Th e regularities in the eff ects of abrasive medium composition and low-frequency vibrations on process productivity and surface layer quality have been experimentally established. It is shown that using a multicomponent mixture of green silicon carbide abrasive grains of 63C50 and 63C25 fractions at an equal mass ratio reduces machining time by 1.5 times compared to the base single-fraction abrasive. Additional application of low-frequency vibrations at 20...55 Hz and an amplitude of 2... 3 mm to the workpiece ensures a further reduction in machining time. It has been establ ished that the proposed method guarantees the preservation of the geometric dimensions of complex-profi le parts within the drawing tolerances with minimal material removal on the disk web (0.01...0.04 mm). Th e process ensures uniform rounding of sharp edges along the blade slot contour with a radius of 0.2...0.3 mm and eff ective polishing of the disk web to a surface roughness of Ra = 0.63...1.25 μm. It is experimentally proven that free abrasive machining does not lead to the degradation of the physical and mechanical state of the surface: the microhardness remains unchanged, and the favorable compressive residual stresses formed during the previous stages of fi nish turning are preserved at the level of 450...550 MPa at a depth of up to 140 μm. It is noted that to eliminate the side eff ect of hole-chamfer erosion on the disk web, the technological process should include their preliminary protection or postpone the chamfering operation to the fi nal stage.