
This work presents the analytical model of H-type linear permanent magnet eddy current brakes (H-type LPMECB). In the presented paper, firstly, the analytical model of the H-type LPMECB was established using the equivalent magnetic circuit method. Secondly, the braking performance of the H-type LPMECB was simulated with the Finite Element Model(FEM) and the analytical model, respectively. The analytical model performance results are consistent with those of the FEM, which validates the analytical model. Hereafter, the nonlinear relationship between the iron foils number of the H-type LPMECB and the braking force was found by the analytical model and the FEM, which provides a guide for the iron foil number selection in future work. Finally, the experimental results are in agreement with the results obtained from the simulations, which also proves the analytical model and the simulation results.
The wall-thinning defect is one of the critical flaws that have been posing a severe threat to the structural integrity of Glass Fibre Reinforced Polymer (GFRP) employed in the hostile environment. In this paper, a sweep-frequency microwave testing method based on Cross-polarization Microwave Reflectometry (CMR) is proposed for detection and imaging of subsurface wall-thinning defects in the unidirectional GFRP. The simulation model of CMR is established along with the scrutinization of the characteristics regarding the testing signal in Ka band (26.5 GHz∼40 GHz). In experiments, a microwave testing system is built up for inspection of GFRPs together with the CMR probe designed using a pair of Ka-band rectangular waveguides based on the simulation model. Imitative subsurface wall-thinning defects and an actual impact defect in GFRP samples are inspected by using the system, and further imaged by using the time-domain signal and Range Migration Algorithm (RMA). The superiority of the proposed method is quantitatively identified through comparison of the signal-to-noise ratio of the imaging result between the CMR and the single-polarization microwave reflectometry.
Touch is important for perceiving the shape and texture of objects. Therefore, its mechanism is utilized in sensors on robots and tactile presentation in virtual reality. However, the mechanism of human tactile perception has not been fully elucidated, although various perceptual phenomena have been confirmed. For example, the hardness and softness (HS) sensation is caused by humans perceiving differences in the rigidity and elasticity of objects; however, this can change depending on the surface properties (called tactile illusion). The purpose of this study was to clarify the HS sensation perception mechanism by focusing on tactile illusion. First, a sensory evaluation was conducted using five samples with the same Young’s modulus but different roughness values. Simultaneously, the contact force and fingertip velocity were measured. The experimental conditions were as follows: the touching motion was a stroking motion; elastic silicone rubber and rigid resin samples were used; and the sensory evaluation was repeated three times to consider the variations in the subjects’ evaluations. As a result, the subjects experienced differences in the HS sensation of samples with different roughness for both samples. For the silicone rubber sample, the microstructural deformation of the sample surface was related to the HS sensation. For the resin sample, the difference in slippage resistance was related to hardness sensation . Therefore, it was found that changes in several physical phenomena occurred when perceiving the HS sensation and that the evaluation criteria changed depending on the presence of deformation.
When addressing higher-order modes, it becomes crucial to adjust the nodal arrangement significantly to simultaneously achieve high accuracy and computational speed. In these scenarios, the meshless method, utilizing only nodes, emerges as a suitable approach. This study illustrates the adaptation of the meshless method to eigenvalue problems encountered in modal analysis, with a specific emphasis on condition numbers and spurious solutions.
The output performance of stick-slip piezoelectric actuators is comprehensively determined by the electro-mechanical responses of the driving unit, control strategy, and the contact status between the driving unit and the slider. Most previously developed inertial piezoelectric actuators face the problems of frequency dependence, motion speed, excessive volume, step resolution, and loading capacity. To exhaustively improve actuation performance, we propose a compact bi-directional piezoelectric-based rotary actuator incorporating the single excitation source, rhombic amplification mechanism, and adjustable preload. The numerical simulations are implemented based on the LuGre friction model, to guide the system optimization. A prototype is fabricated and examined, which accomplishes the maximum load torques of 27.78 and 30.87 N.mm in clockwise and anticlockwise directions, respectively, at the highest rotational velocity of 0.4720 rad/s. Compared with previously reported inertial actuators, the performance of the proposed actuator is significantly enhanced, promising in applications requiring nanometer resolution, long stroke, large holding, and driving forces.