
A magnetic drug delivery system (MDDS) has recently been developed enabling magnetic seeded drugs to be navigated around the diseased parts of the human body. To improve the magnetic drug delivery performance, a portable superconducting bulk magnet system with strong magnetic fields has also been developed. This magnet system primarily consists of small bulk high-temperature superconductors and a compact Stirling-cycle cryocooler. The materials used in the high-temperature superconductors are rare earth 123 single domain compounds (GdBaCuO). The main body of the magnet is 9.5 kg and 740 mm in length. In this study, a bulk magnet was successfully activated using field-cooling magnetization under a superconducting solenoid magnet. The magnetic flux densities at the surface of the vacuum chambers that contain the bulk magnets reached 5.07 T and 6.76 T under the static fields of 6 T and 10 T, respectively. We clarified that the magnetic gradient was approximately 10 T/m at a position 50 mm from the surface of the vacuum chambers. This operating bulk magnet system is portable and can be easily transported via car over long distances.
Two new approaches to fabricate Y123 melt-solidified bulks with excellent superconducting properties have been developed. One is a new method of crystal growth from a seed crystal with its c-axis parallel to the top surface, and the other is a high-temperature annealing process under a moderately reducing atmosphere after crystal growth. In the present study, the former method increased the area of high-Jc regions, and the latter enhanced Jc, particularly at positions far from the seed crystal at low temperatures through suppression of yttrium substitution for barium. The field-trapping property was also improved through introduction of a reductive annealing process prior to oxygen annealing at low temperatures.
A fusion reactor generates a lot of 14 MeV neutrons, some of which penetrate shielding blankets, stream out of ports and reach superconducting magnets. Some important studies were performed in the 1970s and a basic understanding of the mechanisms of neutron irradiation effect was established. Advances in the design concept of nuclear fusion reactors led to the need for consistent studies on the neutron irradiation effect of A-15 strands such as Nb3Sn and Nb3Al, which are strong candidates for fusion reactors. In the early 2000s, a progressive attempt to organize the collaborative research of universities and national institutes was started using a 14 MeV neutron source at Japan Atomic Energy Agency. This paper outlines the neutron irradiation issues related to superconducting magnets for fusion, and a brief history of research on the neutron irradiation effect is provided. In addition, experimental results regarding changes in the superconducting properties of Nb3Sn and Nb3Al strands by neutron irradiation obtained in the newly established collaborative framework are presented, and general mechanisms for the property changes are introduced.
There are high expectations for RE123 wires to be used as future commercial superconductors in the future because of their excellent performance under high magnetic fields and of low cost capabilities. ISTEC, national institutes, universities and companies are taking part in a Japanese national project on electric power devices known as, "Materials & Power Applications of Coated Conductors (M-PACC)". The target applications of the project are SMES, cables and transformers. ISTEC, Fujikura, Showa, Sumitomo and Furukawa are developing RE123 wires for mass-production using various fabrication processes. One of the most important characteristics for practical superconducting wires is, the bending-strain dependence of the critical current. The IC dependencies of RE123 wires for various bending strains were measured using the "Goldacker type" continuous bending apparatus. For tensile bending with the superconductor layer on the outside of the bend, the diameter of the 95% IC retentions was approximately 20 mm for all wires. On the other hand, for compressive bending with the superconductor layer on the inside of the bend, the IC dependencies for the bending diameter were each different. The reversibility strain under bending and straightening was also evaluated using the continuous bending apparatus. These results demonstrate that the IC dependencies for the bending diameter of all wires are suitable for the applications of the M-PACC project.
Magnetic levitation systems using HTS bulks, such as magnetic bearing devices for flywheel energy storage systems, transporters, linear actuators, magnetic gears and so on, have been developed by many research groups. Most of the HTS magnetic levitation systems are composed of HTS bulks and permanent magnets. "Stable magnetic levitation without any other control system" is a specific characteristic of the HTS bulks. A non-contact spin processor and a magnetic-levitation seismic isolation device are introduced as magnetic levitation systems that are composed of HTS bulks and permanent magnets. Furthermore, an active magnetic levitation system using spherical HTS bulks for inertial nuclear fusion and a three-dimensional HTS actuator are introduced as magnetic levitation systems with HTS bulks and electromagnets. Levitation force, levitation gap and stability are closely related to the size and shape of the HTS bulk, the magnetic field distribution around the HTS bulk, the conditions in the field-cooling process of the HTS bulk and so on. Achieving large levitation force, large levitation gap and highly stable levitation is very important for practical use of the HTS magnetic levitation system. Theoretical analysis using a numerical simulation code for understanding electromagnetic behaviors within the HTS bulk is useful for improving the levitation force, levitation gap and stability. Finally, numerical techniques based on the finite element method are introduced in this paper.