Breast cancer is the most diagnosed cancer and the second leading cause of cancer death among women in the world. Compared to some other regions in the world, amount of information available about breast cancer epidemiology in the Kurdistan Region of Iraq is scarce. This study is an attempt to enrich our knowledge about different epidemiological aspects of breast cancer in the region since epidemiological studies contribute quite significantly to the current knowledge of environmental and genetic risk factors and to the current treatment strategies for breast cancer. In addition, studies has shown that the past and ongoing research has a massive implication in improving the outcome of this common disease. This work takes all women diagnosed with breast cancer at Nanakaly Hospital in Erbil, Iraq as sample of the study. Patient characteristics were captured then statistical analysis was performed on these data sets. The majority of patients were found to be city dwellers and about 46% were diagnosed at stage II and 40% at stage III. The vast majority of cases tested positive for hormone receptors but negative for HER2.
The huge impact of COVID-19 worldwide led to the rapid development of vaccines with inadequate data about its longevity, effectivity, and safety. This study aims to evaluate the effectiveness and safety of COVID-19 vaccines available in Iraq and to measure longevity of created antibody response among different time points of both Pfizer-BioNTech and Sinopharm vaccines in Baghdad and Fallujah, Iraq. A two-axis method was used: the first was cross sectional study on the vaccination state for COVID-19 in Baghdad and Fallujah, using an online survey contained questions about city, vaccine type, side effect, pre and post infections, and chronic diseases. The second part involved a prospective observational study of the vaccine’s immunological effectiveness and stability in 60 serum samples from completely vaccinated individuals (second dose) of Pfizer or Sinopharm along different time points (1 - 6 months) by measuring the SARS-CoV-2 Anti-RBD-IgG concentration and evaluating its correlation with pre-infection with COVID-19. Among different types of vaccines available in Iraq, people in Baghdad and Fallujah preferred Pfizer vaccine over other available types, particularly those with chronic diseases. No statistically significant difference was noticed between IgG concentrations at different points of time, IgG concentrations in Pfizer vaccinated individuals were more elevated than Sinopharm, and all of Pfizer vaccinated people showed positive results. Our study established a synergistic impact between recent COVID-19 infection and vaccination, leading to increased levels of IgG antibodies, notably in individuals who received the Pfizer vaccine. Additionally, our findings demonstrate that IgG concentrations remained stable in vaccinated individuals even six months after completing the vaccination with second dose.
The 3-phase asynchronous squirrel cage motors (SCIM) are main competitor machines placed instead of other motors in the commercial and industrial fields. The stator and rotor material selection and construction topology influence the electrical machine design. The results illustrated with the motor of a 15 KW, variable controlled speed, for the constant frequency of 50 Hz or 60 Hz. The motor parameters created inside the simulation model must be matched with the value of a standard parameter for SCIM to achieve a high dynamic response. This work examines the effect of the parameters variation for synchronous motor on the performance characteristics at starting point and at a load change for different time and speed regions. Changing of the rotor power is taken into consideration, this occurs with dynamic change of the hydraulic pump load from the valve. In the industrial applications, production, and manufacturing, till present there are still struggles to find the most holistic environment of the SCIM to achieve its efficiency at the lowest cost and same time control the motor performance, so we predicted the method of reducing the most effective motor parameters to improve the efficiency. The offline method used the SCIM parameters to calculate the time-varying current, torque, and rotor speed. The results illustrated that this method was fully consistent with the experiment tests and the standard theoretical values. A MATLAB program is used to simulate this study. The simulation model proved the feasibility of the proposed method with encouraging performance.
Enhanced oil recovery (EOR) has long proven to be a good method to mobilize the residual oil that is by passed and capillary trapped by secondary recovery methods. Chemical EOR methods enhance the microscopic and macroscopic efficiency, and ultimately the overall oil recovery is improved. However, the adsorption rate of the surfactant, low resistance to high temperature and salinity are some of the factors that would turn chemical flooding impractical and uneconomic in many cases. Lately, the application of nanotechnology in enhanced oil recovery has showcased some good and prolific results in terms of incremental oil recovery. In this study, the applicability of Nanoparticle flooding in carbonate rocks of Pilaspi formation was probed through a series of tests such as thin section analysis, x-ray diffraction, x-ray fluorescence, interfacial tension and contact angle measurements. The results showed that the composition of the carbonate rocks is predominantly calcite (CaCO3) with minor traces of quartz and dolomite. From the interfacial tension (IFT) measurements, it was figured out that the silica and alumina Nanofluids lowered the IFT by 27% and 42% with the light oil, and 43% and 49% with the heavy oil, respectively. The contact angle measurements revealed that the Alumina Nano-fluid at 0.25 wt. % reduced the contact angle on the surface of the light and heavy oil aged thin sections from 169◦ and 115◦ to nearly 119◦ and 78◦. On the other hand, the silica nanoparticle at 0.25 wt. % reduced the contact angles on both thin section types to around 129◦ and 80◦, respectively.
The ever-expanding urban architecture in developing areas requires more land space for construction purposes to be available. For this, utilizing the sub-surface areas through excavations in populous cities is now on the increasing trend. Two major concerns in such excavation projects are excavation-wall stability and the induced ground settlements which can be countered by a soil nailing-ground anchor system. In this regard, influential factors such as nail length and nail inclination angles can affect the overall performance of stabilized ground. Therefore, the focus of the present study is on how the aforementioned influence excavation-induced ground deformations. The numerical simulation is conducted using the software Plaxis 2D. The established numerical models help to explain how changes in the nails’ inclination angles and anchor lengths can change the observed behavior of the walls; from which helpful tips for practicing engineers are drawn accordingly. Such results could also be utilized for classroom presentations to aid students’ understanding of geotechnical engineering concepts.
