Inertial confinement fusion is likely to require significant improvements in technology and design for large targets to implode at high driver energies. To assess the potential for benefits, we report on nuclear performance as a function of target radius R_{t} in direct-drive cryogenic implosions as performed on the OMEGA laser. The neutron yield and areal density are found to increase as R_{t}^{5.0±0.2} and R_{t}^{1.8±0.2}, respectively, and exhibit a much stronger dependence on target radius than previous studies have assumed. As this Letter demonstrates, these types of sensitivities should be expected when implosions are unstable, and have been degraded by a range of multidimensional effects in 3D. If the imperfections in a target and laser system are fixed in magnitude, it follows that larger implosions have higher relative quality, and approach criteria to ignite much more quickly than commonly appreciated.

Considerable progress has been made in deuterium-tritium-layered implosion experiments on the OMEGA Laser System, bringing the prospects for thermonuclear ignition in direct-drive configurations with megajoule-class lasers closer to reality. Doing so has required navigating the balance between improved 1D performance and multidimensional stability. Using statistical modeling based on over 350 cryogenic implosions to identify various degradation mechanisms, and combined with multidimensional simulations and experimental techniques such as target offsets to combat residual flows, core conditions have repeatably been achieved that extrapolate to the burning-plasma state when scaled to 2.15 MJ of symmetric laser illumination. Using high implosion velocities (>450 km/s) and moderately high adiabats (∼5), these experiments produced record-high scaled Lawson parameters in direct drive equal to 89±2% of that required for ignition with expected yields of up to 1.5±0.2 MJ. To improve these results still further, focused physics studies are performed to improve physics understanding and identify routes to even greater performance. Recent studies include investigations into the impact of mounting features, laser imprint, reduced fuel temperatures, and greater on-target intensities through subscale experiments. This manuscript gives a summary of the cryogenic direct-drive program on the OMEGA laser, including routes taken to achieve the current best performance, the status of recent focused physics investigations, and future designs—such as target solutions to laser imprint and reducing vapor density to increase convergence—that are expected lead to the demonstration of hydro-equivalent ignition on OMEGA.

The need to accurately predict radiation transport in stellar interiors and inertial confinement fusion targets provides a clear motivation for spectral opacity measurements of hot dense plasmas. In principle, laser-driven implosions provide a platform to access extreme plasma conditions (densities ρ>ρ0, electron temperatures Te> 400 eV), hard to reach by other methods. In this scheme, an element embedded in the shell is compressed by capsule convergence and heated by conduction from the central hot spot, which also provides a bright broadband x-ray source for absorption spectroscopy. We present an experimental study of absorption spectroscopy with capsules combining two distinct tracer element layers, respectively, titanium and vanadium, embedded in the plastic shell of direct-drive laser implosions at the OMEGA laser facility. The presented work is one of the scarce studies on absorption spectroscopy in an implosion configuration so far, and the use of two elements simultaneously has the advantage of bringing more stringent constraints on the atomic-physics models underlying our radiation-hydrodynamics simulations. Using two layers at different depths also enables us to characterize and benchmark the simulated density and temperature gradients inside the shell. Comparisons between simulated and measured time-integrated and time-resolved spectra are presented, and a good agreement is found, which validates our radiation-hydrodynamics and atomic physics models. The measurements presented here pave the way toward future opacity studies of elements increasingly relevant for astrophysical applications.

The achievement of ignition in the laboratory has renewed interest in defining the requirements for a future high-gain inertial confinement fusion (ICF) facility. Our best chance of predicting future ICF performance is with 3-D radiation hydrodynamic simulations that have been benchmarked against experimental data, but their high computational cost is prohibitive for use in practical design studies. We introduce a hierarchical approach where 3-D simulations are tuned to match experimental measurements and used to train 3-D degradation models in 1-D simulations allowing for accurate predictions over the entire OMEGA direct-drive database. A genetic algorithm was used in combination with the trained 1-D simulations to search for optimal direct-drive implosion designs at driver energies ranging from 20 kJ to 10 MJ. As the fidelity of 3-D codes improves, this approach will provide a viable experimentally informed tool for defining the next ICF facility.

A new neutron time-of-flight (nTOF) detector for yield and ion-temperature measurements in deuterium-tritium (DT) implosions was designed, installed, and calibrated on the OMEGA Laser System. This detector was installed at θ = 46.8° from the vertical and φ = 84.9°, previously a region without other detectors, in order to decrease the uncertainty of low-mode asymmetry measurements by six other nTOF detectors. The new nTOF detector uses the "PMT only" concept [Glebov et al., Rev. Sci. Instrum. 92, 013509 (2021)] and consists of a Photek photomultiplier tube (PMT)-110 in a thin aluminum housing. There is no lead shielding in front of the PMT to allow measurements of the x-ray instrument response function of the detector. The detector is installed in the OMEGA H2-port line of sight at 9.3 m from the target chamber center in the OMEGA Target Bay and is called the H2 nTOF detector. The H2 nTOF measures DT yields in the 1 × 1013 to 3 × 1014 range and ion temperatures from 2 to 12 keV. H2 nTOF reduced the hotspot flow uncertainty in the z-direction from ±10 to ±8 km/s, and the uncertainty in the anisotropic flow axis from σθ = ±26° to ±13° and σφ = ±25° to ±21°. The design details, performance, and calibration results of the H2 nTOF detector in DT implosions on OMEGA will be presented.

This paper presents a simple physics-based model for the interpretation of key metrics in laser direct drive. The only input parameters required are target scale, in-flight aspect ratio, and beam-to-target radius, and the importance of each has been quantified with a tailored set of cryogenic implosion experiments. These analyses lead to compact and accurate predictions of the fusion yield and areal density as a function of hydrodynamic stability, and they suggest new ways to take advantage of direct drive. To provide examples, we discuss how the inferred mix width behaves relative to theory and then show how it could be exploited to perform a direct drive implosion with a Lawson metric or χ_{noα} of 0.24±0.02-using a novel parameter space at high velocities and beam radii on the OMEGA laser-that projects to ignition at a laser energy of ≤2.0 MJ.

Focussing laser light onto the surface of a small target filled with deuterium and tritium implodes it and leads to the creation of a hot and dense plasma, in which thermonuclear fusion reactions occur. In order for the plasma to become self-sustaining, the heating of the plasma must be dominated by the energy provided by the fusion reactions—a condition known as a burning plasma. A metric for this is the generalized Lawson parameter, where values above around 0.8 imply a burning plasma. Here, we report on hydro-equivalent scaling of experimental results on the OMEGA laser system and show that these have achieved core conditions that reach a burning plasma when the central part of the plasma, the hotspot, is scaled in size by at least a factor of 3.9 ± 0.10, which would require a driver laser energy of at least 1.7 ± 0.13 MJ. In addition, we hydro-equivalently scale the results to the 2.15 MJ of laser energy available at the National Ignition Facility and find that these implosions reach 86% of the Lawson parameter required for ignition. Our results support direct-drive inertial confinement fusion as a credible approach for achieving thermonuclear ignition and net energy in laser fusion.

Neutron time-of-flight (nTOF) spectrometers are essential instruments for measuring and evaluating the performance of inertial confinement fusion implosions. The neutron spectrometers utilized for the OMEGA laser include two liquid-based scintillators, each consisting of a large volume filled with xylene that is coupled to four photomultiplier tubes. Analysis of the signal from these detectors requires detailed knowledge of the scintillator's light output, which is needed to fit the nTOF spectrum, from which the neutron energy spectrum is informed. The light output is nonlinearly proportional to the neutron energy, which, in turn, affects the interpretation of the neutron energy spectrum from a TOF signal. A recent campaign on OMEGA was performed to calibrate the xylene detectors and infer the shape of the light-output curve. The campaign utilized materials with increasing Z placed in the OMEGA target chamber to initiate scattering events with the 14 MeV fusion neutrons. This process leads to the production of backscatter neutrons of varying energies that appear as peaks in the nTOF data. Simulations using a neutron transport code were combined with the measured deuterium-tritium neutron yields to calculate the expected backscattered neutron yields from the well-known scattering cross sections of each material. The neutron-energy dependent light output of the scintillator inferred from the experiment is compared to the light-output curve simulated with a neutron transport code for the following neutron energies: 1.5, 2.5, 6, and 14 MeV.

Irradiating a small capsule containing deuterium and tritium fuel directly with intense laser light causes it to implode, which creates a plasma hot enough to initiate fusion reactions between the fuel nuclei. Here we report on such laser direct-drive experiments and observe that the fusion reactions produce more energy than the amount of energy in the central so-called hot-spot plasma. This condition is identified as having a hot-spot fuel gain greater than unity. A hot-spot fuel gain of around four was previously accomplished at the National Ignition Facility in indirect-drive inertial confinement fusion experiments where the capsule is irradiated by X-rays. In that case, up to 1.9 MJ of laser energy was used, but in contrast, our experiments on the OMEGA laser system require as little as 28 kJ. As the hot-spot fuel gain is predicted to grow with laser energy and target size, our work establishes the direct-drive approach to inertial fusion as a promising path towards burning and ignited plasmas in the laboratory. Additionally, we report a record (direct-drive) fusion yield of 0.9 kJ on OMEGA, which we achieved with thin-ice deuterium–tritium liner targets.

We show that an x-ray emission signature associated with acceleration phase mass injection [R. C. Shah et al., Phys. Rev. E 103, 023201 (2021)] correlates with poor experimental hot-spot convergence and a reduced neutron production relative to expectations. It is shown that with increased target mass as well as with higher-design adiabats, this signature is reduced, whereas with increased debris on the target, the signature is increased. We estimate that the vapor region in typical best designs may have up to 2x the assumed hydrogen mass at the start of deceleration.

Shock-driven implosions with 100% deuterium (D_{2}) gas fill compared to implosions with 50:50 nitrogen-deuterium (N_{2}D_{2}) gas fill have been performed at the OMEGA laser facility to test the impact of the added mid-Z fill gas on implosion performance. Ion temperature (T_{ion}) as inferred from the width of measured DD-neutron spectra is seen to be 34%±6% higher for the N_{2}D_{2} implosions than for the D_{2}-only case, while the DD-neutron yield from the D_{2}-only implosion is 7.2±0.5 times higher than from the N_{2}D_{2} gas fill. The T_{ion} enhancement for N_{2}D_{2} is observed in spite of the higher Z, which might be expected to lead to higher radiative loss, and higher shock strength for the D_{2}-only versus N_{2}D_{2} implosions due to lower mass, and is understood in terms of increased shock heating of N compared to D, heat transfer from N to D prior to burn, and limited amount of ion-electron-equilibration-mediated additional radiative loss due to the added higher-Z material. This picture is supported by interspecies equilibration timescales for these implosions, constrained by experimental observables. The one-dimensional (1D) kinetic Vlasov-Fokker-Planck code ifp and the radiation hydrodynamic simulation codes hyades (1D) and xrage [1D, two-dimensional (2D)] are brought to bear to understand the observed yield ratio. Comparing measurements and simulations, the yield loss in the N_{2}D_{2} implosions relative to the pure D_{2}-fill implosion is determined to result from the reduced amount of D_{2} in the fill (fourfold effect on yield) combined with a lower fraction of the D_{2} fuel being hot enough to burn in the N_{2}D_{2} case. The experimental yield and T_{ion} ratio observations are relatively well matched by the kinetic simulations, which suggest interspecies diffusion is responsible for the lower fraction of hot D_{2} in the N_{2}D_{2} relative to the D_{2}-only case. The simulated absolute yields are higher than measured; a comparison of 1D versus 2D xrage simulations suggest that this can be explained by dimensional effects. The hydrodynamic simulations suggest that radiative losses primarily impact the implosion edges, with ion-electron equilibration times being too long in the implosion cores. The observations of increased T_{ion} and limited additional yield loss (on top of the fourfold expected from the difference in D content) for the N_{2}D_{2} versus D_{2}-only fill suggest it is feasible to develop the platform for studying CNO-cycle-relevant nuclear reactions in a plasma environment.

Diffusion-dominated mix in inertial confinement fusion (ICF) is characterized where the majority of the mix occurs in the immediate fuel-shell interface while hydrodynamic-dominated mix pulls shell material from farther away into the central fuel. A thin (150 nm) separated reactants ICF mix platform is highly sensitive to the amount of mix from the first micron of shell-fuel interface. This fine-spatial resolution platform has revealed that material mix in moderate convergence (CR similar to 12) ICF implosions is dominated by a diffusion mechanism. This technique has now been expanded across a set of OMEGA ICF implosions, observing an increase in mix width and mix amount for cooler, slower, and more compressive implosions. Hydrodynamic simulations require a buoyancy-drag mix model to capture the increasing mix width, suggesting a transition between these two mix mechanisms.

In direct-drive inertial confinement fusion, the laser bandwidth reduces the laser imprinting seed of hydrodynamic instabilities. The impact of varying bandwidth on the performance of direct-drive DT-layered implosions was studied in targets with different hydrodynamic stability properties. The stability was controlled by changing the shell adiabat from (α_{F}≃5) (more stable) to (α_{F}≃3.5) (less stable). These experiments show that the performance of lower adiabat implosions improves considerably as the bandwidth is raised indicating that further bandwidth increases, beyond the current capabilities of OMEGA, would be greatly beneficial. These results suggest that the future generation of ultra-broadband lasers could enable achieving high convergence and possibly high gains in direct drive ICF.

The ion velocity distribution functions of thermonuclear plasmas generated by spherical laser direct drive implosions are studied using deuterium-tritium (DT) and deuterium-deuterium (DD) fusion neutron energy spectrum measurements. A hydrodynamic Maxwellian plasma model accurately describes measurements made from lower temperature (< 10 keV), hydrodynamiclike plasmas, but is insufficient to describe measurements made from higher temperature more kineticlike plasmas. The high temperature measurements are more consistent with Vlasov-Fokker-Planck (VFP) simulation results which predict the presence of a bimodal plasma ion velocity distribution near peak neutron production. These measurements provide direct experimental evidence of non-Maxwellian ion velocity distributions in spherical shock driven implosions and provide useful data for benchmarking kinetic VFP simulations.

Magnetized liner inertial fusion (MagLIF) is a fusion concept that uses magnetized, preheated fuel to reduce the implosion velocities and convergence ratios required for ignition. A scaled, laser-driven experimental platform to study MagLIF has been demonstrated on the OMEGA laser system, providing comprehensive experimental data on MagLIF scaling, utilizing the higher shot rate on OMEGA compared to the Z machine. Using this platform, a broader experimental space for MagLIF has been studied. Presented in this article are experimental results that demonstrate that the combination of preheat and magnetization enhances the neutron yield by 470% compared to a reference implosion, significantly more than the yield enhancement by the field or preheat alone. These results are achieved while maintaining a relatively low convergence ratio (<20). The experiments were supported by one-, two-, and three-dimensional radiation-hydrodynamics simulations, all of which suggest that multiple sources of mix play different key roles depending on the scale of the MagLIF experiment.

Ion temperatures serve as an important diagnostic for inertial confinement fusion (ICF) implosions. In direct-drive ICF experiments on OMEGA, neutron-time-of-flight (nTOF) data are used to infer the ion temperature of the fusing plasma produced in the implosion experiment. The analysis of the nTOF data requires an assumption about the shape of the underlying source signal. Since the source nTOF signal is a near-replica of the neutron energy spectrum, an ideal Gaussian shape, corresponding to the neutron energy spectrum of a uniform temperature plasma, is routinely employed. However, spatial and temporal variations of the ion temperature in the plasma give rise to higher-order moments, which were first described by Munro [Nucl. Fusion 56, 036001 (2016)]. In this work, we show a simpler alternative analysis to derive moments of the neutron energy spectrum for a plasma with variations in ion temperature. We also present a revised analysis of measured nTOF signals that uses a model with an additional degree of freedom to take into account the effect of ion temperature variations on the shape of the spectrum. Compared to presently used nTOF analysis, the revised analysis yields on average ≈2× more accurate fits to the data and up to 15% higher ion temperatures for cryogenic experiments. Furthermore, we quantify the ion temperature inflation caused by radially symmetric fluid flows, which are present even in a symmetric implosion, and which serve as a lower bound on the ion temperature inflation in real implosions.

The National Diagnostic Working Group (NDWG) has led the effort to fully exploit the major inertial confinement fusion/high-energy density facilities in the US with the best available diagnostics. These diagnostics provide key data used to falsify early theories for ignition and suggest new theories, recently leading to an experiment that exceeds the Lawson condition required for ignition. The factors contributing to the success of the NDWG, collaboration and scope evolution, and the methods of accomplishment of the NDWG are discussed in this Review. Examples of collaborations in neutron and gamma spectroscopy, x-ray and neutron imaging, x-ray spectroscopy, and deep-ultraviolet Thomson scattering are given. An abbreviated history of the multi-decade collaborations and the present semiformal management framework is given together with the latest National Diagnostic Plan.

Three-dimensional effects play a crucial role during the hot-spot formation in inertial confinement fusion (ICF) implosions. A data analysis technique for 3D hot-spot reconstruction from experimental observables has been developed to characterize the effects of low modes on 3D hot-spot formations. In nuclear measurements, the effective flow direction, governed by the maximum eigenvalue in the velocity variance of apparent ion temperatures, has been found to agree with the measured hot-spot flows for implosions dominated by mode ℓ=1. Asymmetries in areal-density (ρR) measurements were found to be characterized by a unique cosine variation along the hot-spot flow axis. In x-ray images, a 3D hot-spot x-ray emission tomography method was developed to reconstruct the 3D hot-spot plasma emissivity using a generalized spherical-harmonic Gaussian function. The gradient-descent algorithm was used to optimize the mapping between the projections from the 3D hot-spot emission model and the measured x-ray images along multiple views. This work establishes a platform to analyze 3D low-mode core asymmetries in ICF.

In laser-driven implosions for laboratory fusion, the comparison of hot-spot x-ray yield to neutron production can serve to infer hot-spot mix. For high-performance direct-drive implosions, this ratio depends sensitively on the degree of equilibration between the ion and electron fluids. A scaling for x-ray yield as a function of neutron yield and characteristic ion and electron hot-spot temperatures is developed on the basis of simulations with varying degrees of equilibration. We apply this model to hot-spot x-ray measurements of direct-drive cryogenic implosions typical of the direct-drive designs with best ignition metrics. The comparison of the measured x-ray and neutron yields indicates that hot-spot mix, if present, is below a sensitivity estimated as ∼2% by-atom mix of ablator plastic into the hot spot.