The ultraviolet(UV) continuum slope of galaxies, beta, is a powerful diagnostic of the metallicity and ages of stars, nebular gas properties, dust content, and the escape of Lyman continuum (LyC) photons. In this study, we present beta measurements for 395 spectroscopically confirmed galaxies at 5 < z < 14.3 selected primarily from JADES, using high-quality JWST (James Webb Space Telescope) NIRSpec/PRISM spectra. We find a median beta = -2.15, finding a mild increase in blueness of beta with increasing redshift and fainter UV magnitudes. Interestingly, we find evidence for reddening of the average beta at z > 9.5, deviating from the trend observed at z < 9.5. Using stacked spectra in bins of redshift and beta, we derive trends between beta and dust attenuation, metallicity, ionization parameter, and stellar age indicators, finding a lack of dust attenuation to be the dominant driver of bluer beta-values. We furtherreport five galaxies with beta <=-2.9, which show a range of spectroscopic properties and signs of significant LyC photon leakage. Finally, we show that the redder beta-values at z > 9.5 may require rapid build-up of dust reservoirs in the very early Universe or a significant contribution from the nebular continuum emission to the observed UV spectra, with the nebular continuum fraction depending on the gas temperatures and densities. We show that in the absence of dust, nebular emission at ne > 10 000 cm-3 can reproduce the range of red beta that we see in our sample. Higher gas densities can also redden the nebular continuum emission, potentially explaining the observed beta-values.
Abstract The increasing demand for electricity and the need for decarbonization has intensified interest in natural gas–hydrogen fuel blends as an alternative for gas turbine systems. However, limited studies have evaluated their performance under tropical climate conditions. This study presents the energy, exergy, and exergoeconomic analysis of a combined cycle power plant operating with natural gas–hydrogen mixtures, with hydrogen fractions ranging from 0% to 100% in increments of 10%. The effect of compressor inlet air cooling is also assessed for temperatures between 8.8 °C and 15 °C. Results indicate that reducing the compressor inlet temperature to 8.8 °C maximizes gas turbine power output and reduces nitrogen oxide emissions. Increasing the hydrogen fraction enhances power output, particularly above 60% hydrogen, with gains between 0.06% and 0.54% per 10% increment. Exergy destruction decreases by up to 1.52%, while exergy efficiency shows a slight decline. From an economic perspective, electricity generation cost increases significantly for hydrogen fractions above 60%. These findings suggest that moderate hydrogen blending improves system performance and emissions, whereas high hydrogen concentrations require careful economic evaluation.
Active galactic nuclei (AGNi) are a key ingredient in galaxy evolution and possibly shape galaxy growth through the generation of powerful outflows. Little is known regarding AGN-driven ionized outflows in moderate-luminosity AGNi (log(L-bol/erg s(-1))<47) beyond cosmic noon (z greater than or similar to 3). In this work we present the first systematic analysis of the ionized outflow properties of a sample of seven X-ray-selected AGNi (log(L-X/erg s(-1))>44) from the COSMOS-Legacy field at z similar or equal to 3.5 and with log(L-bol/erg s(-1)) = 45.2-46.7 by using JWST NIRSpec/IFU near-IR spectroscopic observations as part of the "Galaxy Assembly with NIRSpec IFS" (GA-NIFS) program. We spectrally isolated and spatially resolved the ionized outflows by performing a multi-component kinematic decomposition of the rest-frame optical emission lines. JWST/NIRSpecIFU data also revealed a wealth of close-by companions, of both non-AGN and AGN nature, and ionized gas streams likely tracing tidal structures and large-scale ionized gas nebulae extending up to the circumgalactic medium. Ionized outflows were detected in all COS-AGNi targets, with outflow masses in the range 1.5-11x10(6) M-circle dot, outflow velocities in the range similar or equal to 570-3200 km s(-1), and mass outflow rates in the range similar or equal to 1.4-40 M-circle dot yr(-1). We compared the outflow properties of AGNi presented in this work with previous results from the literature up to z similar or equal to 3, which were opportunely (re-)computed for a coherent comparison. We normalized outflow energetics (M-out, & Edot;(out)) to the outflow density in order to standardize the various assumptions that were made in the literature. Our choice is equal to assuming that each outflow has the same gas density. We find GA-NIFS AGNi to show outflows consistent with literature results, within the large scatter shown by the collected measurements, thus suggesting no strong evolution with redshift in terms of total mass outflow rate, energy budget, and outflow velocity for fixed bolometric luminosity. Moreover, we find no clear redshift evolution of the ratio of mass outflow rate and kinetic power over AGNi bolometric luminosity beyond z>1. In general, our results indicate no significant evolution of the physics driving outflows beyond z similar or equal to 3.
When fabricating, it is common to follow a prescribed set of steps in a tutorial or how-to. While popular, such explicit knowledge resources have many inconsistencies and omissions, use static illustrations, and cannot adapt to drop-in makers or a maker's mistakes. To overcome many of these issues, this work presents Automatics, a novel explicit knowledge resource system that dynamically generates fabrication activities for one or more makers based on their current environmental and fabrication context. Automatics assigns tasks to makers based on the past tools and components the maker was working with, enables makers to recover from mistakes through model regeneration, suggests alternative tools if a needed tool is unavailable or in use, and allows multiple makers to drop-in throughout a fabrication activity. Initial usage and feedback from novice makers showed that Automatics increases the number of tasks that can be completed compared to paper instructions, decreases frustration, and improves one's understanding of the global context of assigned tasks during fabrication activities.