The Florida Department of Transportation (FDOT) is a decentralized agency charged with the establishment, maintenance, and regulation of public transportation in the state of Florida. The department was formed in 1969. It absorbed the powers of the State Road Department (SRD). The current Secretary of Transportation is Jared W. Perdue.
This paper introduces a horizontal 3D concrete printing (3DCP) method for the continuous construction of large shell structures, such as pipes, tunnels, and roofs. Unlike conventional vertical 3DCP, which faces limitations in height, print reach, and pumpability, the proposed approach allows for scalable, on-site fabrication of shell structures without requiring post-printing assembly. By tilting the print layers and utilizing previously printed inclined surfaces for support, this method enables horizontal concrete printing to form elongated shell structures. An integrated simulation-experiment framework is demonstrated as a template for 3DCP process control, where two concrete shells were printed to validate the proposed technique, and their deformation behavior was analyzed through both experiments and numerical simulations. The results indicate that vertical deformation does not accumulate indefinitely but stabilizes after certain layers, confirming the feasibility of the continuous horizontal printing method.
The organic-rich shale facies of the Lower Jurassic Datta Formation in the Upper Indus Basin in Pakistan was studied using geological and geochemical investigations to assess the unconventional shale oil reservoir potential. The Datta shale facies is a promising oil-prone stratum, consisting of total organic carbon (TOC) exceeding 2 wt%, and primarily comprising Type II and II/III kerogens, with a hydrogen index (HI) exceeding 250 mgHC g(-1) TOC. The Datta shale facies is also characterized by higher free hydrocarbon (S-1) content than TOC, resulting in a high oil saturation index (OSI) between 30.81 and 298.7 mgHC g(-1) TOC, wherein the high OSI of more than 100 mgHC g(-1) TOC indicates a strong potential for oil production. This finding is consistent with the current thermally mature oil window, which ranges between early mature and peak mature, as supported by vitrinite reflectance (%VRo) values of up to 0.82. This main oil-generation window leads to the conversion of extensive hydrogen-rich kerogen for commercial oil generation, with a transformation ratio (TR) of up to 65%, as demonstrated by 1D basin modelling. Maximum oil generation, with TR values exceeding 50%, leads to high pressure and results in microfracture pores in the Datta shale facies. The presence of non-fabric-fracture pores is confirmed by high-resolution petrographical scanning electron microscopy (SEM). Consequently, these findings highlight that the Datta shale facies should be considered for use as an unconventional shale oil reservoir, with the suggestion of hydraulic fracturing techniques for production purposes.
This research project funded by Florida Department of Transportation (FDOT) provided the opportunity to characterize #11 (36-mm diameter) GFRP bars that are not currently considered in ASTM specifications, but recently added to the FDOT FY2024–25 sect. 932 material specification. Accordingly, and based on the experimentally-obtained properties of these large-diameter bars, a waterline pile cap footing was selected and designed. As a result, a comprehensive design philosophy and workflow is proposed for GFRP reinforced concrete (GFRP-RC) bridge footings. The case-study waterline pile cap footing is located in the Florida coastal zone and was originally designed in 2017 based on AASHTO LRFD Bridge Design Specifications, seventh edition (2014) using conventional carbon steel reinforcement. The main objectives of this study are to: (1) redesign the foundation with GFRP bars while keeping the cap geometry unchanged; (2) analytically validate the Ultimate Limit State (ULS) and Service Limit State (SLS) designs with the AASHTO LRFD Bridge Design Guide Specifications for GFRP (2018) using a commercial FEM software; (3) compare the amount of #11 GFRP reinforcement with that of carbon steel bars in the as-built drawings of the original steel-RC design; and, (4) discuss the challenges in detailing, including the anchorage length of GFRP #11 bars and minimum bent bar sizes to meet both SLS and ULS requirements. The foundation was designed using both the properties defined by the FDOT FY2024–25 Specifications and those obtained from experimental tests, highlighting that the design with GFRP bars is more restrictive at the SLS and in detailing compared to steel-RC.
This research project, funded by the Florida Department of Transportation (FDOT), evaluates the use of Glass Fiber Reinforced Polymer (GFRP) bars to address the significant risk of deterioration in the waterline pile cap footings that support bridge piers built in tidal zones. Traditionally, concrete foundations are reinforced with steel bars up to #11 (36-mm diameter) with thick concrete cover and durability-enhanced concrete mix designs. Both current design standards ACI CODE-440.11(2022) and AASHTO LRFD Bridge Design Guide Specifications for GFRP-Reinforced Concrete (2018) do not include the use of #11 or larger bars, which are ideal for pile cap footings or elements that may be susceptible to large design forces including vessel collision or hurricane wave and wind loadings. Additionally, existing literature lacks scientific research and experimental testing for large diameter FRP bars. The objective of this research project is to perform a comprehensive physio-mechanical characterization of #11 or larger GFRP bars including tensile strength, transverse and horizontal shear and other relevant properties such as bond strength to concrete. To achieve this objective, a series of different tests were carried out in accordance with ASTM standards on #11 GFRP bars, produced from two different manufacturers.