Cyan Systems has continued to mature our small pixel camera performance, including improvements in the packaging, optics, and electronics. The associated camera components demonstrate key resolution and enabling capabilities. We report on recent results from our new digital readout integrated circuit (DROIC) small pixel mid-wave infrared camera with an ultra-high-definition (3840 x 2160) format, in addition to demonstrations with Cyan’s CS-3 full-high-definition (1920 x 1080) camera. We address small pixel spatial sampling and modulation transfer function issues as the pixel size shrinks, and we examine the difference between the performance of present devices and the new generation of small pixel cameras.
Provides society information that may include news, reviews or technical notes that should be of interest to practitioners and researchers.
In this work, a polymer‐derived ceramic composite was formulated using polysilazane resin, silicon carbide microfiber reinforcement, and fumed alumina rheology modifier. Demonstration pieces and flexural test specimens were 3D printed using direct ink writing, a type of material extrusion additive manufacturing technology. Printed specimens were cured and then pyrolyzed at 1200°C in argon, resulting in 3D‐printed polymer‐derive ceramic composites. Flexural test specimens were tested in 3‐pt. flexure at room temperature and at high temperature (1200, 1400, 1500, and 1600°C). Flexural strength increased from 97.8 ± 20.1 MPa at room temperature to 367 ± 88 MPa and 401 ± 54 MPa at 1200 and 1400°C, respectively. Strength decreased to ∼184 MPa at 1500°C and was not measurable at 1600°C. Microscopy of fracture surfaces reveals evidence of degradation of the matrix phase above 1400°C and x‐ray diffraction reveals the formation of mullite above 1200°C.
Additive manufacturing by digital light processing (DLP) has advanced rapidly, and micro-printers are now commercially available that use lens systems to expose arrays of 1920 x 1080 pixels of 2 μm x 2 μm size with ultraviolet (UV) light, while higher resolution printers with even smaller pixels are in development. Selective polymerization by localized UV curing on this scale enables microfabrication of features around 10 μm, while offering print rates sufficient for parts on the order of centimeters. In addition to UV curable polymers, ceramics can be additively manufactured by DLP, either by curing suspensions of ceramic particles or preceramic polymers. We present a novel interposer fabrication process based on additive manufacturing, whereby interposers can be created with near arbitrary routing of electrical signals. We first present the method to create a ceramic dielectric using micro stereolithography of a preceramic resin slurry. Then we explore the use of solder alloys with high capillary action to fill vias with aspect ratios greater than 100:1 by melt infiltration. Finally, we present two interposer demonstrations relevant to imaging applications, including ceramic interposers containing arrays of vias with diameters and pitches as small as 9 μm and 18 μm, respectively and sizes up to 2 cm x 2 cm x 0.7 cm. After melt infiltration of the vias with a copper indium solder, via resistivities as low as ~4 x 10-8 Ω·m were measured, close to 2X the international annealed copper standard. With our novel approach, we demonstrated two different interposer designs: 1) a curved interposer intended to connect a curved infrared detector with a planar read-out integrated circuit (ROIC); and 2) a fan-out interposer that spreads the pitch of an array of vias from 60 μm to 220 μm. These interposers require thousands of curved and angled vias, respectively, that cannot be realized using conventional microelectronics processing approaches. The unprecedented via routing enabled by this additive technology offers new packaging options for the 3D integration of microelectronic subsystems beyond imaging applications.
Reconfigurable or tunable metasurfaces are of great interest for adaptive multi-modal sensing and imaging. Phase change materials (PCMs) have been recently explored for reconfigurable optical devices such as spatial light modulators and metasurfaces. In this talk, we will present large-scale reconfigurable infrared metasurfaces consisting of greater than 30 million pixelated optical antennas integrated with PCM mesa structures over a 1cm x 1cm area.