
Optimally windowed chirp rheometry-a technique employing both frequency and amplitude-modulated exponential chirps-is gaining popularity for its ability to precisely capture the linear viscoelastic spectrum of complex materials while dramatically reducing the experimental time required to acquire data. To date, the chirp signals used for characterizing the linear viscoelasticity of such materials have featured a high time-bandwidth product (TB > 50), calculated as the product of chirp duration or experiment time (T-owc) and frequency bandwidth (Delta omega). However, for time-evolving materials, it is essential to also adjust the chirp duration (T-owc) according to the characteristic mutation timescale, tau(mu) (t) of the material to ensure time-translation invariance (T-owc << tau(mu)(t)) during experiments. For rapidly mutating materials, the values of the time-bandwidth product TB thus systematically decrease as the chirp duration is progressively reduced during the mutation process. However, the signal must also be sufficiently long, relative to the material's inherent relaxation timescale (tau), to ensure that a steady-state periodic viscoelastic response is obtained. To explore the trade-offs between these two competing conditions, we perform exploratory numerical simulations using canonical constitutive models: the classical Maxwell model, characterized by a single dominant relaxation time and the fractional Maxwell model, which compactly and accurately captures the broad relaxation spectra typical of many viscoelastic materials. For highly viscoelastic systems and/or rapidly mutating samples, we show that when employing short exponential chirp sequences, substantially improved accuracy can be obtained by shifting the initial phase of the chirp waveform through a single new phase offset parameter, phi(0). Experimental validation tests performed on wormlike micellar solutions, a pressure-sensitive adhesive, and a UV-curable acrylate system-each having relaxation times comparable to the signal duration-further demonstrate that adjusting the initial phase significantly enhances the data quality of linear viscoelastic measurements made with optimally windowed chirp protocols.
The transport and temperature-time history of disk-shaped firebrands was studied with high-speed thermal imaging in a wind tunnel. One millimeter diameter wooden disks were ignited using a novel firebrand generator. The firebrands dropped vertically into a wind tunnel crossflow. Optical images of the firebrands were recorded at 960 frames/second during their transport in the wind tunnel test section at three different wind speeds. The resulting high speed color videos were processed using a particle tracking algorithm and a two color pyrometry technique to determine temperature, position, and velocity time histories of individual firebrands. The firebrand temperatures were observed to oscillate at distinct frequencies that ranged between 50Hz and 480Hz (the Nyquist frequency of the imaging system). A positive correlation was observed between the temperature fluctuation frequency and the relative speed of the firebrand compared to the wind speed. The observed high speed temperature fluctuations suggest that rapid transitions between glowing and flaming combustion may be an important aspect in firebrand transport phenomena and should be considered within the context of model development.
Encoding local variations in the peel force response of pressure-sensitive adhesives (PSAs) unlocks new functional possibilities for applications requiring both strong adhesion and facile, user-directed detachment. Recent studies have demonstrated that liquid crystalline elastomers (LCEs) with monodomain planar orientation function as anisotropic adhesives, exhibiting direction-dependent peel forces based on LCE alignment. Building on these findings, we investigate the ability to engineer peel force profiles through spatial patterning of director alignment. We systematically analyze adhesion of patterned LCEs with planar director orientation by varying spatial pattern frequency, polymer composition, peel velocity, backing stiffness, and adhesive thickness. LCE PSAs with both binary (stepped) and gradient (graded) patterning of orientation, and therefore peel force, are demonstrated. Our results establish design parameters that define the minimum resolvable pattern length scale, offering insights for tuning local adhesion contrast in LCE-based PSAs.
Hydrothermal alkaline treatment (HALT) is an emerging thermochemical process capable of degrading and defluorinating ultrashort-, short-, and long-chain per- and polyfluoroalkyl substances (PFAS) in high total dissolved solids wastewaters. HALT operates under subcritical water conditions (T > 300 degrees C, P > 20 MPa) with the addition of sodium hydroxide, which raises the pH and degrades PFAS via various reaction mechanisms including thermal decarboxylation and nucleophilic substitution. In this study, a commercial-scale HALT system was employed to degrade and defluorinate PFAS in a concentrated industrial wastewater stream produced from an ion exchange resin regeneration process. Numerous operating conditions were tested to assess the extent of PFAS degradation, extent of defluorination, and any production of fluorinated byproducts under relatively mild HALT conditions. An extensive suite of analytical techniques was employed to track the fate of fluorine and to identify and characterize any potential reaction intermediates. Results showed that relatively mild HALT conditions could be employed to degrade and defluorinate fluoroalkylcarboxylic acids (FCAs), with some degradation and defluorination of perfluorosulfonic acids (PFSAs). De-tuning of the process (via decreasing temperature, hydroxide concentration, and increasing flow rate) produced minor yields of volatile organic fluorine (VOF) compounds in the form of 1H-perfluoroalkanes (e.g., H-CnF2n+1), consistent with the known HALT reaction mechanisms and pathways. Furthermore, more recalcitrant PFSAs could be effectively managed via an adsorption polishing step rather than using more aggressive HALT conditions. Technoeconomic analyses show that HALT processing of this wastewater stream can be more cost effective than off-site transportation and incineration.
The miniaturization of thermal sensors for mobile platforms inherently limits their spatial resolution and textural fidelity, leading to blurry and less informative images. Existing thermal super-resolution (SR) methods can be grouped into single-image and RGB-guided approaches: the former struggles to recover fine structures from limited information, while the latter relies on accurate and laborious cross-camera calibration, which hinders practical deployment and robustness. Here, we propose 3M-TI, a calibration-free Multi-camera cross-Modality diffusion framework for Mobile Thermal Imaging. At its core, 3M-TI integrates a cross-modal self-attention module (CSM) into the diffusion UNet, replacing the original self-attention layers to adaptively align thermal and RGB features throughout the denoising process, without requiring explicit camera calibration. This design enables the diffusion network to leverage its generative prior to enhance spatial resolution, structural fidelity, and texture detail in the super-resolved thermal images. Extensive evaluations on real-world mobile thermal cameras and public benchmarks validate our superior performance, achieving state-of-the-art results in both visual quality and quantitative metrics. More importantly, the thermal images enhanced by 3M-TI lead to substantial gains in critical downstream tasks like object detection and segmentation, underscoring its practical value for robust mobile thermal perception systems.