Developing an environmentally friendly and more efficient pulping process is necessary to cope with the pollution issues created by the current pulp and paper mills. Although Organosolv pulping is considered environmentally friendly compared to kraft or soda pulping, the higher cost hindered the commercialization of the Organosolv process to pulp different raw materials. Therefore, this research aimed to explore the papermaking potential of three raw materials i.e., spruce, beech, and miscanthus, using Acetosolv pulping. This research also includes the determination of properties of the fibers influenced by refining and application potential that could arise for the fibers in terms of strength, barrier, and optical properties. Paper sheets showed excellent air barriers, which justifies their applications in the packaging sector. It was concluded that if the tensile index is the selection criteria, then even miscanthus (a nonwood material) Acetosolv pulp can replace the spruce softwood kraft pulp. Also, transparency and contact angle were found to be maximum for spruce which can facilitate its application as a substrate in green electronics.
Polymer composite materials find application in various life sectors such as packaging, lightweight construction and the fabrication of medical devices. Functional fillers like mineral colloids, synthetic and natural fibres enable a precise tailoring of the mechanical properties of the resulting compounds. Precipitated calcium carbonate (CaCO3, PCC) has proven to be a special popular mineral polymer filler. From economic and ecologic reasons, it is desirable to increase filler contents in polymers while maintaining material strength. To achieve this, the present work has developed a hybrid filler system which is based on carboxymethylated, fibrillated cellulose fibres. CaCO3 is precipitated onto the fibres in a single step twin-screw extrusion process by the co-precipitation method. This process ensures a strong, permanent interaction between the fibres and the mineral particles, which enables CaCO3 contents in the filler of up to 68 wt.-%. The resulting hybrid fillers were compounded with polypropylene (PP) in a powder or paste state with filler contents between 5 wt.-% and 20 wt.-%. The resulting composites show an increase in the zero-shear viscosity and, in the event of sufficient network formation, a marked increase in stiffness was observed.
Natural fibres from regional plants like miscanthus grass have gained a lot attention as a replacement of synthetic fibres due to their eco-friendly nature, abundant local availability, low cost, reducing food versus fuel competition and their applications in bio-based composites. Nevertheless, the polar nature of natural fibres usually leads to a weak interfacial compatibility with hydrophobic thermoplastic matrices, resulting in poor strengths of the composites. In our study a way to prepare cellulose-based composites in a two-step extrusion process is investigated. The cellulosic fibres are first fibrillated from refined miscanthus fibres through (chemo-)thermomechanical pulping by extrusion. The fibre morphology including the aspect ratio is measured by field flow fractionation with optical measurement system. Infrared spectroscopy is applied to analyse the degree of substitution (DS) values quantitatively. In a second extrusion step, the modified cellulosic fibres are compounded with cellulose acetate (CA) and cellulose acetate butyrate (CAB) to cellulose-based injection-mouldable composites. The thermal, rheological, mechanical and morphological properties are characterised to analyse the composites. The properties of the composites prepared by this method are compared with their unmodified grades and with composites using drop-in biopolymers bio-based polypropylene (bio-PP) and bio-based polyethylene (bio-PE) as matrices. It shows, that the mechanical properties of mechanically fibrillated cellulose fibres reinforced CA are comparable to glass fibre reinforced polypropylene with similar fibre weight content. We have also seen, that the influence of mechanical fibrillation exceeds the influence of the chemical modification.
This publication presents the results of the fundamental research on the interaction of laser radiation and lignocellulosic fibres with respect to the melting of the fibre main components cellulose, hemicellulose and lignin. In the first part, hand sheets made of different lignocellulosic fibres were irradiated with laser radiation from a carbon monoxide laser. Fluence-dependent interaction regimes, the dynamics of flash pyrolysis and chemical changes due to irradiation are discussed. Using a high-speed camera, an intermediate liquid state could be observed as a result of the irradiation. This is decomposed into gaseous reaction products by a highly dynamic boiling process. In addition to the time-resolved investigations, extensive FTIR studies were carried out. The second part is intended to further investigate former work on melting of cellulose. The basic idea is to combine laser radiation and mechanical pressure by compressing the sample between two steel bolts and simultaneously irradiating the joint. The processed samples show some visual indications of intermediate melting, such as increased transparency or flow behaviour. However, these can be traced back to effects that do not require a melting state.