There are presented case studies of MIC in various industrial systems, mainly from carbon and stainless steels, which failed - water pipeline, sprinkler systems, sewage pipeline, cooling pipeline, water tanks, etc.. The identification of MIC was done according to morphology of corroded surface, chemical analysis of deposits, water analysis, etc. Bacterial tests for BSR and IRB were done, too.
SVUOM specialists have participated in many activities concerning corrosion failure analysis or testing the materials/coatings for corrosion protection in power industry (e.g. temporary protection of various parts of power plants, long-term corrosion behaviour of weathering steels and mild steel with hot dip galvanised coating (HDG) and paint coatings of poles, reconstruction of parts of nuclear plants, etc.). There are many materials and corrosion protective coatings used for infrastructure of power industry – the SVUOM main interest is focused to distribution network.
Results are summarized of the feasibility of using slip-dissolution model of stress corrosion crack growth for the evaluation of stress corrosion cracking (SCC) susceptibility of duplex stainless steels in hydrogen sulfide-chloride environments at 120°C. First a brief note is presented about the historical background of the concept of discussion of SCC results received in the constant extension rate test (CERT) of stainless steels in terms of phenomenological model that incorporates a slip-dissolution mechanism and elastic-plastic fracture mechanics, introducing of the average near crack-tip strain rate, eT and average crack growth rate αav as quantities measurable in CERT test has allowed a comparison to existing theoretical model of Ford. This idea has been used in our slow strain rate tests (SSRT) of duplex stainless steels (DSS) in hydrogen sulfide-chloride environments at 120°C. It is shown that experimental values of eT and αav determined in SSRT experiments for several duplex stainless steels in 20%NaCl-H2S (pH=4) at 120°C can be used for calculation of input parameters of the slip-dissolution model for stress-corrosion cracking. It has only been possible due to exact analysis of stress-vs.-strain curves and the determination of supposed value for fracture-strain of oxide film at crack tip, f. (Values of rate constant for the bare surface reaction at the crack tip, k and current decay exponent at the crack tip, m estimated for various partial pressures H2S (ppH2S) made possible the evaluation of changing electrochemical conditions under which cracks occur in various DSS during mentioned SSRT experiments.
Elektrochemische potentiokinetische Reaktivierungsverfahren, aber auch andere Polarisationsverfahren, eignen sich als quasi zerstörungsfreie Verfahren zur Beschreibung der Korrosionsbeständigkeit von Stählen und Legierungen ohne besonders anspruchsvoll an die Probenvorbereitung zu sein. Sie sind auch für die Überprüfung fertiger Bauteile oder als Vorortprüfung bereits im Betrieb befindlicher Komponenten, insbesondere im Bereich von Schweißverbindungen oder an Auftragsschweißungen anwendbar. Gegenüber den Standardprüfungen sind sie schneller, empfindlicher, objektiver und quasi quantitativ. Sie sind nicht nur für die Untersuchung austenitischer Standardstähle geeignet, sondern auch bei hochlegierten ferritischen, martensitischen und Duplex-Stählen sowie Nickelbasis-Legierungen und selbst bei niedrig- bis mittellegierten Stählen. Durch diese Prüfverfahren lässt sich sowohl die Empfindlichkeit gegen interkristalline Korrosion als auch gegen Lochfraß oder selektiven Angriff nach Wärmeeinwirkung verschiedener Art ermitteln. Sie geben aber auch Aufschluss über die allgemeine Korrosionsbeständigkeit oder über Gefügeänderungen, die in den Werkstoffen eintreten können. Mit Rücksicht auf die langjährige Erfahrung mit solchen Methoden, die ausgehend von frühen Entwicklungen inzwischen auf verschiedenste Werkstoffe und die unterschiedlichsten gefügebedingten Korrosionsvorgänge angewendet werden, kann man erwarten, dass sich ihr noch weitere Anwendungsgebiete erschließen werden, sowohl in der Forschung als auch als national und international genormte Untersuchungsmethode. On the development of the electrochemical potentiokinetic reactivation method – the EPR-test Electrochemical potentiokinetic reactivation methods, but also other polarisation methods, are suitable as quasi non destructive testing methods to describe the corrosion resistance of steels and alloys without needing a very pretentious surface preparation. They may be used also to check finished components or even on site such in service, especially welding areas or weld overlays. Compared to standard tests they are quicker, more sensitive, more objective and quasi quantitative. They may be applied not only with austenitic standard steels but also with high alloyed ferritic, martensitic or duplex steels as well as with nickel based alloys. After any case of heat treatment the sensitivity to intergranular corrosion but also to pitting or selective attack can be determined by these testing methods. They may inform on the general corrosion resistance or the microstructural changes which may occur with materials, too. Based on the experience of many years with such methods which, starting from the early developments, have now been applied to very different materials, one may attend new fields of application in research and also as a nationally and internationally testing standard.