
Establishing a stable, low-resistance interface is essential for addressing the interfacial limitations between alkali metal anodes and solid electrolytes in high energy density solid-state sodium batteries. In this work, a ∼500 nm thick conversion-type SnO2 interlayer was deposited directly at room temperature onto Na3Zr2Si2PO12 (NZSP) solid electrolyte discs using the powder aerosol deposition (PAD) method to improve the compatibility of sodium (Na) metal with the NZSP surface. In contrast to unmodified Na|NZSP|Na symmetric cells that suffer from progressive interfacial degradation and consequently limited critical current density, symmetric cells incorporating PAD-SnO2 interlayers on both sides of the NZSP discs (Na|PAD-SnO2|NZSP|PAD-SnO2|Na) show a significantly reduced interfacial resistance and enhanced critical current density up to 9.5 mA cm−2 at 70 °C without any thermal post-treatment. Long-term galvanostatic cycling at 0.3 mA cm−2 showed stable Na+ plating/stripping overvoltages of ∼7.4 mV for more than ten days. These findings outperform recently published CuO interlayers and demonstrate the suitability of PAD for the room temperature fabrication of functional interlayers that stabilize the Na|NZSP interface. This method may provide a basis for scalable, fully PAD-processed architectures for next-generation solid-state sodium batteries.
Lignin electro-oxidation at the anode offers a promising route to couple biomass valorization with low-voltage H2 production, yet most reported systems rely on transition-metal catalysts. Here we show that simple acid engineering transforms commercial Vulcan carbon into an efficient metal-free anode for lignin electro-oxidation in alkaline media below 100 °C. Nitric acid treatment reveals an optimum surface state, with the 48 h-treated sample (C-N(48)) outperforming pristine carbon and other treatment times. Subsequent phosphoric acid modification further enhances activity, notably using 15 wt% H3PO4, with the sequentially treated C-N(48)-P(15) material delivering the best performance. Under anodic polarization (1.73 V vs. RHE), lignin oxidation displays a pronounced time-dependent activation that is absent in lignin-free electrolyte and ultimately surpasses the current observed for water oxidation alone under identical conditions. Textural analysis rules out porosity effects, while XPS and Raman spectroscopy indicate that activity depends on a balanced combination of oxygen-containing surface groups, graphitic domains and structural disorder. In-situ Raman further reveals potential-induced restructuring only in the presence of lignin, consistent with the formation of a dynamic, lignin-responsive active interface. These findings identify scalable, metal-free carbon anodes tailored for lignin-first electrolysis and highlight surface-engineered carbons as promising platforms for sustainable anodic upgrading.
Developing high-performance and long-lasting non-precious metal bifunctional electrocatalysts toward the oxygen reduction and evolution reactions (ORR/OER) is of great importance for the development of rechargeable zinc–air batteries (ZABs). In this work, a novel hierarchical catalyst consisting of NiFe nanoalloys encapsulated within graphitic C 3 N 4 -coated carbon nanotubes (denoted as NiFe@C 3 N 4 -CNT) was constructed via pyrolysis of NiFe-based metal organic frameworks (MOF) precursors anchored on CNTs mixed with dicyandiamide. This architecture provided a well-dispersed distribution of active NiFe sites and ensures intimate contact between the conductive carbon matrix and catalytic domains, thus facilitating fast charge/mass transport and maintaining robust structural integrity. The resulted NiFe@C 3 N 4 -CNT catalyst achieved improved bifunctional activity, attributed to the regulated electronic structure of Ni and Fe sites embedded in hierarchical C 3 N 4 /CNT conductive matrix. The catalyst achieves a low potential gap (0.76 V) with an ORR half-wave potential of 0.778 V and an OER overpotential of 315 mV at a current density of 10 mA cm −2 . The manufactured ZAB using this catalyst demonstrated a power density of 137.05 mW cm −2 and a high specific capacity (544.24 mAh g −1 ), and stable cycling performance over 130 h, demonstrating superior cycling stability to the commercial Pt/C + RuO 2 benchmark. The superior catalytic performance mainly arised from the tuned electronic structure of NiFe bimetallic sites, while the multi-dimensional conductive pathways formed within CNTs/C 3 N 4 hybrid matrix enhance directional electron transfer and active site accessibility, greatly improving both activity and stability.