
This study investigates the thermo-photocatalytic reduction in CO2 to methane over copper-modified TiO2 (P25) and TiO2/g-C3N4 catalysts, building upon prior works that identified two top-performing systems: 0.8%Cu-TiO2/g-C3N4 prepared via mechanochemical synthesis, and 0.2%Cu-TiO2 prepared by aqueous impregnation. Comprehensive physicochemical characterisation, including ICP-OES, XPS, FT-IR, UV–Vis DRS, UPS, and PL spectroscopy, was conducted to explain the structural, electronic, and surface properties of the catalysts. Temperature-dependent catalytic tests in a 2D-flow reactor ranging from room temperature to 70 °C under UV irradiation (368 nm) with water and ethanol vapour revealed methane production maxima at 50–60 °C, with rates of ~1010 µmol/g⋅h for 0.2%Cu-TiO2 and ~720 µmol/g⋅h for 0.8%Cu-TiO2/g-C3N4, significantly exceeding those of pristine P25. Moderate heating enhanced charge carrier mobility, ethanol functioned effectively as a hole scavenger, and CO2 reduction kinetics were accelerated. Beyond the optimal temperature, a decline in performance attributed to reactant desorption counterbalanced these improvements. Copper species contributed through providing active sites for CO2 chemisorption and charge-transfer processes, generating a synergistic effect that surpassed purely photocatalytic performance upon heating. These findings underscore the roles of the synthesis method and defect engineering in optimising catalyst performance and demonstrate the potential of combining photonic and thermal energy inputs to improve sustainable CO2 conversion technologies.
Graphene hydrogels are attractive electrode materials for aqueous electrochemical devices. The reduction level of their graphene building blocks governs the balance between electron transport and electrolyte accessibility, but has rarely been tuned within a single gelation process. Here, we report an acidity-controlled Zn-induced interfacial gelation that concurrently achieves the self-assembly of 3D porous graphene hydrogels and systematic control of their reduction level. Simple addition of HCl to an aqueous graphene oxide dispersion modulates interfacial reduction and assembly on a Zn surface, raising the residual oxygen content of the reduced graphene oxide framework from 15.4 to a maximum of 23.2 at.% and modifying the porous architecture. At an intermediate HCl addition, the moderately reduced hydrogel combines a restored π-conjugated carbon network with retained oxygen functionality and develops the largest gel thickness and specific surface area. A supercapacitor based on this hydrogel delivers the highest specific capacitance of 70.2 F g−1 among the hydrogels, with sustained rate capability and cycling stability. These findings highlight the reduction level as a key design parameter for graphene hydrogel electrodes, demonstrating a facile route for concurrently tuning surface chemistry and porous architecture during interfacial gelation.
Catalytic activity for redox reactions is crucial for solid oxide fuel cells (SOFCs) design to improve the electrochemical performance. In this work, an impregnation strategy is adopted as the primary design principle to achieve both high oxygen reduction reaction (ORR) activity and low polarization resistance. A misfit-layered oxide cathode, Ca3Co4O9-δ (Ca349), is studied, along with composite cathodes fabricated with Sm0.2Ce0.8O1.9 (SDC) (Ca349-SDC) and a Ni0.9Cu0.1Ox-SDC anode. Their electrochemical properties are characterized via electrochemical impedance spectroscopy (EIS) and current–voltage (I–V) measurements using symmetric cells and single cells, respectively. After impregnating the Ca349 cathode with SDC for four cycles, the minimum polarization resistance (Rp) reaches 0.07 Ω·cm2 at 800 °C, which is much lower than that of the pristine Ca349 cathode (0.31 Ω·cm2). The Ca349-SDC//SDC//Ni0.9Cu0.1Ox-SDC single cell delivers a peak power density of 662 mW·cm−2 at 800 °C, which is 453 mW·cm−2 higher than that of the Ca349//SDC//Ni0.9Cu0.1Ox-SDC single cell. This study not only advances the rational design of SOFCs but also provides a generalizable framework for next-generation electrochemical energy conversion technologies.
Graphene and graphene oxide (GO) exhibit exceptional tensile strength and elastic modulus, and the functional groups on GO promote dispersion and accelerate hydration in cementitious matrices. This study uses molecular dynamics (MD) simulations to investigate the mechanical behaviour of graphene/GO-reinforced calcium silicate hydrate (C-S-H) at the nanoscale. A reactive force field (ReaxFF) with modified C/O parameters was developed to describe atomic interactions between C-S-H and graphene/GO. A more realistic C-S-H structure with varying calcium-to-silicon (Ca:Si) ratios was produced by removing silicate chain segments from tobermorite, followed by grand canonical Monte Carlo (GCMC) simulation to introduce water molecules and hydroxyl groups. Functional groups in GO formed extensive hydrogen bonds with neighbouring water and hydroxyl groups in the C-S-H matrix. At a Ca:Si ratio of 1.7, carboxyl-functionalized GO formed the most hydrogen bonds and achieved 26% higher pull-out strength than hydroxyl- and epoxy-functionalized GO. Graphene/GO improved x- and y-direction tensile performance relative to plain C-S-H, whereas the z-direction (out-of-plane) tensile properties were lower than those of plain C-S-H. Nevertheless, GO sheets bridged disconnected C-S-H globules, giving a z-direction tensile strength of 0.15–0.59 GPa, whereas pristine and defective graphene contributed negligibly (0.003–0.03 GPa). Tailoring GO functionalization and providing adequate anchorage length are therefore key to optimizing GO-reinforced C-S-H.
Colloidal quantum dot (CQD) near-infrared photodetectors have attracted a lot of interest in the fields of optical communications, environmental surveillance, imaging technologies, and wearable sensors, due to their tunable bandgaps and flexible solution processibility. In particular, AgBiS2 CQDs have been considered a promising candidate nanomaterial for near-infrared photon detection because of their non-toxicity and environmental friendliness. However, the performance improvement of AgBiS2 CQD-based photodetectors is still limited by the high trap states density and relatively low carrier transport properties of CQD film. Herein, we demonstrate a simple and effective strategy to enhance the photoresponse performances of AgBiS2 CQD-based devices by constructing SnO2/AgBiS2 bulk nano heterostructures (BNH). By finely controlling the addition of SnO2 nanocrystals, the non-radiative recombination in AgBiS2 CQDs film was suppressed while the carrier transport in the composite film was simultaneously improved. As a result, the optimized device with 7 wt% SnO2 (ASN7) exhibited a responsivity of 0.161 mA/W and an estimated detectivity of 5.85 × 108 Jones, which are approximately 11.5-fold and 3.5-fold higher than those of the control device, respectively. Additionally, the response speed was significantly accelerated. This work offers an effective approach for enhancing the photoelectrical properties of lead-free AgBiS2 CQD-based near-infrared optoelectronics.