
A strain‐compensated constitutive description and candidate high‐efficiency domains were examined for hot deformation of the GH4065A Ni‐based superalloy. Isothermal compression tests were performed at 910–1110 °C and 0.001–10 s −1 . Complete flow curves at 960–1110 °C and 0.001–1 s −1 were used to develop a strain‐compensated hyperbolic‐sine Arrhenius model over true strains of 0.10–0.80. Calibration against 240 paired stress points gave R = 0.991, AARE = 8.46%, and RMSE = 20.1 MPa, while additional tests at 985 and 1085 °C were used to assess temperature interpolation. At true strains of 0.30–0.45, high‐efficiency domains were identified at 960–990 °C below ~0.0067 s −1 and at 1025–1090 °C and 0.0025–0.05 s −1 . The latter was identified as a candidate processing window, with positive ξ values at the mapped strains. Grain size increased from 5.2 to 66.4 μm between 1060 and 1110 °C at 0.1 s −1 , whereas increasing strain rate from 0.001 to 1 s −1 at 1110 °C refined grain size from ~240 to 17 μm. EBSD indicates DDRX as the dominant recrystallization mode, supplemented by CDRX. Primary γ′ particles regulate grain‐boundary migration and particle‐associated nucleation, while the reported recrystallized fractions represent post‐deformation endpoint values.
This paper separately investigates the effects of variable density and variable direction design on the quasistatic compressive response of triply periodic minimal surface (TPMS) structures and subsequently proposes an integrated optimization strategy. First, the variable density design is investigated. The elastic modulus remains nearly constant at 295 MPa across all gradients, but increasing the linear gradient coefficient from 0.5 to 1.5 reduces the yield strength and plateau stress by 13.4% and 11.3%, respectively, while total energy absorption varies by merely ±1.34%. Then, the variable direction design is analyzed. Rotating the lattice to 45° increases the elastic modulus by 39.6% to 416 MPa and raises the specific energy absorption by 43.6% to 64.2 J/g, which confirms that load capacity and load uniformity can be independently adjusted. Based on these findings, a series of TPMS structures combining variable density and variable direction is constructed. In the three‐point bending test, the peak load of the 2D optimized beam increased by 27.79% compared with the uniform beam. However, for the supporting beam, the peak load and energy absorption of the 3D optimized beam improved by 15.36% and 19.83%, respectively.
Magnesium alloys with biodegradable properties are being explored for potential use in orthopedic implants. However, the alloy used as an implant is subjected to a combined effect of wear and corrosion termed tribocorrosion. During various movements of the human body, the frequency of the implant at the interface undergoes changes, which affect the corrosion characteristics. This study substantiates the tribocorrosive properties of AZ91D magnesium alloy immersed in Ringer's solution. The investigation has been conducted under reciprocating motion at varying loads of 2 and 5 N and frequencies of 1 and 3 Hz. At a lower frequency, the formation of corrosive products stabilizes on the surface at a higher load of 5 N, thereby enhancing the corrosion resistance of the alloy. Conversely, at a higher test frequency of 3 Hz, the alloy has demonstrated increased corrosion resistance at a lower load of 2 N due to the rapid repassivation process and subsurface hardening of the alloy. The microstructural characteristics of the corroded surface and subsurface have been analyzed using scanning electron microscopy with energy dispersive spectroscopy. Additionally, Raman spectroscopy and X‐ray photoelectron spectroscopy have been employed to identify the nature of the corrosive products formed.
This study systematically compared the microstructural evolution and mechanical properties of TC4 titanium alloy and a new TC4‐0.5 wt.% Nb‐0.5 wt.% Ni (TC4‐NbNi) titanium alloy in three conditions (hot‐rolled, single‐annealed, and double‐annealed). The results show that the addition of trace amounts of niobium and nickel enhances the stability of the β phase, raising the β‐phase transformation temperature to 986 °C. In the hot‐rolled and single‐annealed conditions, these trace elements significantly refined the spacing of the α lamellar phase. After double annealing, the TC4‐NbNi alloy formed a bimodal microstructure consisting of an interlaced primary equiaxed α phase and a fine, strip‐like secondary α phase. Ni and Nb are enriched in the β phase and exist primarily in a solid‐solution state, resulting in a high density of intragranular dislocations and substructures. Mechanical testing indicates that, thanks to solid‐solution strengthening, microstructural refinement, and the bimodal structure formed by dual annealing, the TC4‐NbNi alloy achieves an excellent balance between strength and toughness. The tensile strength of the hot‐rolled alloy is 1021 MPa, and its impact toughness is 44.9 J; after dual annealing, the tensile strength and yield strength are further increased to 1052 and 993 MPa.
A device is developed to coat a SiC fiber tow with BN by low pressure chemical vapor deposition in a cold wall reactor. A motorized spool system is installed to feed the tow into the reactor in preparation for continuous processing in the future. In the present work, the system is used solely to control the mechanical tension of the tow, which is held stationary and heated by microwaves. The heating process induces a temperature gradient, with the temperature decreasing from the core to the surface of the multifilament tow. The precursor gas used is triethylamine borane mixed with ammonia. X‐Ray photoelectron spectrometry analyses demonstrate the feasibility of depositing a boron nitride coating with good purity. Key parameters include the preferred use of N 2 over H 2 as a carrier gas and a sufficiently large reactor diameter. Deposition growth rates are determined in situ by interferometry from non‐contact pyrometric measurements. Deposition kinetic regimes are identified as a function of temperature. The kinetics are limited by chemical reactions up to at least 1500 °C, before being limited by mass transfer and precursor depletion at the highest temperatures.