
The increasing global energy demand, coupled with the depletion of fossil-based resources, necessitates the development of sustainable, plant-based alternatives to mitigate CO₂ emissions, a leading driver of climate change. Fatty acids derived from renewable sources, such as crude palm oil (CPO) and coconut oil, offer a promising solution due to their molecular structure, which shares key characteristics with hydrocarbons while also featuring a carboxyl functional group. In the pursuit of hydrocarbon production, the removal of this carboxyl group is essential, typically achieved through processes such as decarbonylation or hydrodeoxygenation. This study explores the oxidative decarboxylation of fatty acids, utilizing a biomimetic catalytic approach under relatively mild conditions—atmospheric pressure and moderate temperatures. Air served as the oxidant, with manganese (Mn) as the catalyst and copper (Cu) as the co-catalyst. Reactions were conducted at 110°C to 150°C, with a fatty acid-to-catalyst mass ratio of 13:0.1 to 13:1, using dimethyl sulfoxide as the solvent and air supplied at 1 liter per minute. The results indicate that myristic acid exhibits a higher degree of conversion compared to lauric acid. Lauric acid conversion ranged between 27.70% and 34.49%, while myristic acid conversion ranged from 26.70% to 52.70%. The resulting product was analyzed according to the ASTM D-86 method, with the decarboxylation of lauric acid yielding a boiling range of 98°C to 250°C—within the typical range for gasoline and aviation turbine fuel. This approach offers a promising, energy-efficient route to bio-hydrocarbon production under mild aerobic conditions, contributing to the global transition towards renewable energy sources.
Biopolymer films integrated with natural antimicrobial represent a sustainable strategy for enhancing food safety and shelf life. This study characterizes a functional starch-chitosan (S-CH) film incorporated with lemongrass essential oil (LEO). GCMS identified α-citral as the primary antimicrobial component of the LEO. The film was prepared using the casting technique, and the influence of LEO concentration on mechanical properties, hydrophobicity and surface morphology were determined. The findings show that the tensile strength and elongation at break of the S-CH-LEO films were lower than those of the S-CH film, making them brittle and less stretchy. The incorporation of LEO from 0.05% to 0.15% had increased tensile strength and elongation at break from 0.143 MPa to 0.873 MPa and from 3.81% to 8.63%, respectively. The hydrophobicity of S-CH-LEO films increased with the increase in LEO, as evidenced by a higher water contact angle range between 52.30° and 84.80°. S-CH-LEO 0.15% film was the best formulation, with a tensile strength of 0.873 MPa, an elongation at break of 8.63%, and a contact angle of 71.50°. This study shows that S-CH-LEO films improve moisture resistance, a critical factor for extending the food shelf life. Therefore, despite the lower tensile strength and elongation at break, the resulting improvements in water resistance and functional bioactivity suggest that S-CH-LEO films are viable solution for active food packaging applications.
Climate change intensifies saltwater intrusion in coastal and delta regions, notably the Mekong Delta, thereby increasing the concentration of chloride ions (Cl-) in water. Elevated Cl- concentrations pose serious environmental challenges, inhibiting plant growth and impacting human health. While various conventional methods for chloride treatment exist, challenges persist concerning high cost, complex procedures, and secondary waste. Therefore, developing a simple, cost-effective, and highly efficient method using novel adsorbent materials is imperative. The primary objective of this study was to prepare and evaluate the efficacy of bismuth oxide nanoparticles (Bi2O3) as a novel, highly effective adsorbent for the removal of Cl- from saline water sources. Bi2O3 nanoparticles were synthesized using the solid dispersion evaporation technique with sorbitol as a support. FTIR, XRD, SEM, and EDX were used to characterize the physicochemical and structural properties of the material. The Cl- removal capacity was systematically studied under diverse operational conditions, including contact time, solution pH, adsorbent dosage, initial Cl- concentration, and temperature, to determine appropriate adsorption conditions. The material was also subjected to adsorption-desorption cycling tests to evaluate its regeneration potential and long-term durability. The kinetic study showed that the Bi2O3 material reached adsorption equilibrium efficiently after 90 minutes. The maximum Cl- adsorption capacity was 40.89 mg/g at an optimum solution pH of 4, under optimized conditions (initial Cl- concentration of 50 mg/L, 25 °C). Other investigated factors significantly influenced the adsorption kinetics and capacity. Crucially, the Bi2O3 adsorbent maintained its high removal efficiency over 10 regeneration cycles, confirming its excellent durability and potential for real-world applications. The results clearly demonstrate that the synthesized Bi2O3 nanoparticles have excellent potential as a robust, high-performing adsorbent for Cl- removal, suggesting a viable and practical solution to the challenges posed by saltwater intrusion.
Coagulation and flocculation are essential processes in water and wastewater treatment. However, commonly used commercial coagulants pose environmental and health risks due to residual metal content and the large volumes of sludge they produce. As a sustainable alternative, starch-based biocoagulants have attracted increasing research interest due to their biodegradability, cost-effectiveness, and lower sludge generation, with some studies reporting up to 5-fold lower sludge volumes than with conventional chemical coagulants. Among these, non-conventional starches offer a promising solution because of their diversity, regional availability, and lack of competition with the food supply. This review explores extraction methods, modification strategies, and characterization techniques for structural and mechanistic validation. Reported studies revealed excellent pollutant removal performance under optimal conditions, including turbidity (98.91%), TSS (90.7%), COD (84.96%), color (100%), and selected metals (100%). Normalized removal efficiencies ranged from1.855% per mg/L for turbidity, 0.541% per mg/L for COD, and 1.7778% per mg/L for TSS, depending on the starch source and wastewater type. Mechanisms such as charge neutralization and interparticle bridging have also been identified. Despite challenges such as composition variability, high dosage requirements, and scalability issues, techno-economic assessments suggest potential industrial applicability. Overall, non-conventional starch-based biocoagulants hold considerable promise for sustainable wastewater treatment applications.
Electrodialysis (ED) is an efficient technique for treating high-salinity industrial effluents. This study examined the removal efficiencies of sodium chloride (NaCl), sodium acetate (C2H3NaO2), and acetic acid (CH3COOH) using electrodialysis. The procedure utilized a cation exchange membrane type MK-40 and an anion exchange membrane type MA-40. The impact of operational parameters, including electrolysis time, initial concentration, and applied current, was examined. The findings indicated that the removal efficiency improved over time, reaching 70% for NaCl at an initial concentration of 0.086 M and an applied current of 1 A. The elimination efficiency of C2H3NaO2 attained a maximum value of 97% at a concentration of 0.036 M and an applied current of 1 A. The maximum removal efficiency of acetic acid was 71%, achieved at a starting concentration of 0.033 M with an applied current of 1 A. The findings indicated that the current efficiency peaked at elevated initial concentrations of all examined contaminants, whereas increasing the applied current significantly enhanced removal efficiency. Consequently, electrodialysis is an efficient technique for removing certain contaminants from industrial effluents.