
This study analyses the joint influence of aperture width and rim angle on the optical performance of a parabolic trough collector (PTC). Using Tonatiuh-based Monte Carlo ray tracing, 52 configurations combining aperture widths of 3–6 m and rim angles of 30°–150° were assessed under normal incidence. Average heat flux and flux distributions were used to identify favourable geometries, while ray-number convergence and optical-error sensitivity were assessed for the highest-performing configuration. Average heat flux increased with rim angle up to an intermediate optimum and then decreased due to focal broadening and spillage. The optimum rim angle was 100° for aperture widths of 3, 4, and 5 m, producing maximum average heat fluxes of 21,501.6, 28,453.8, and 35,145.7 W/m², respectively. For the 6 m aperture, the optimum shifted to 110°, yielding 41,279.8 W/m². Results observed with 10,000 rays deviated by at most 1.14% from 50,000-ray reference cases. For the 6 m–110° configuration, a 2.5 mrad slope error combined with ±16 mrad tracking errors reduced average heat flux by nearly 67%. The wide-range sweep, convergence check, and error analysis differentiate nominal optima from robust designs, demonstrating that aperture width and rim angle must be optimized jointly and that accurate manufacturing, alignment, and tracking are essential.
Efficient and sustainable technologies for disinfection of domestic wastewater are critical for safeguarding public health and the environment, as pathogens and contaminants threaten human well-being and ecological balance. The application of UV radiation is considered an environmentally sound alternative, as it does not alter the physicochemical characteristics of treated effluents nor produce hazardous by-products. Nevertheless, concerns persist about the durability of UV lamps under adverse conditions, the susceptibility of systems to mechanical failure, and reduced efficiency derived from suspended solids that induce clogging, fouling and attenuation of UV radiation. The study assesses the impact of suspended solids by comparing unfiltered wastewater (UFWW) and filtered wastewater (FWW) under low (471 mW∙s/cm²), medium (941 mW·s/cm²), and high (3722 mW·s/cm²) UV doses at 254 nm. Disinfection efficiencies were nearly 99% across all treatments, indicating that solids concentration (<50mg/L) does not significantly impair UV performance. E. coli inactivation, measured by most probable number (MPN), achieved efficiencies of ≥99.9% in all cases. Logarithmic inactivation values ranged from 2 to 4 for TABC, MPN, and qPCR, confirming that higher UV doses enhance microbial inactivation. This study also evaluates the effectiveness of microbiological (Total Aerobic Bacteria Count – TABC) and molecular (quantitative real-time polymerase chain reaction – qPCR). Results showed that qPCR, targeting the rpoB gene, detected higher microbial recovery (2 log) compared to TABC, highlighting its superior sensitivity. The study underscores the advantages of UV disinfection, including its efficiency, compact design, and cost-effectiveness compared to chemical methods.
La desinfección de aguas residuales domésticas es crucial para proteger la salud pública y el medio ambiente, ya que elimina patógenos y contaminantes que representan riesgos significativos. Implementar metodologías eficientes y sostenibles en este proceso es esencial para garantizar la seguridad del agua y su reutilización en diversos contextos. La radiación ultravioleta (UV) es un proceso de desinfección física ampliamente reconocido como una alternativa ecológica a los tratamientos químicos, ya que no altera las propiedades fisicoquímicas de los efluentes tratados ni genera subproductos nocivos. La luz UV inactiva los microorganismos dañando su material genético e impidiendo su reproducción. Este estudio evalúa la eficacia de un sistema de desinfección UV diseñado para el tratamiento de aguas residuales domésticas, utilizando métodos microbiológicos (recuento total de bacterias aerobias - RTBA) y moleculares (PCR cuantitativa en tiempo real - qPCR) como metodologías de recuento. Los resultados mostraron que la qPCR, dirigida al gen rpoB, detectó una mayor recuperación microbiana (2 log) en comparación con el RTAB, lo que pone de manifiesto su mayor sensibilidad. El estudio también evaluó el impacto de los sólidos en suspensión comparando las aguas residuales no filtradas (ARNF) y las aguas residuales filtradas (ARF) bajo dosis bajas (471 mW∙s/cm²), medias (941 mW·s/cm²) y altas (3722 mW·s/cm²) de UV a 254 nm. Las eficiencias de desinfección alcanzaron casi el 99% en todos los tratamientos, lo que indica que la concentración de sólidos (< 50mg/L) no afecta significativamente al rendimiento de la UV. La inactivación de E. coli, medida por el número más probable (NMP), alcanzó eficacias ≥99,9% en todos los casos. Los valores logarítmicos de inactivación oscilaron entre 2 y 4 para RTAB, NMP y qPCR, lo que confirma que las dosis UV más altas mejoran la inactivación microbiana. El estudio subraya las ventajas de la desinfección UV, incluida su eficacia, diseño compacto y rentabilidad en comparación con métodos químicos.
As conventional oil and gas resources approach the later stages of their development lifecycle, it is becoming increasingly clear that existing reserves are insufficient to sustain society's growing needs. Unconventional oil and gas reservoirs, however, boast substantial energy reserves. Should these resources be harnessed and developed efficiently, they have the potential to significantly augment the world's energy supply. Nevertheless, most unconventional oil and gas reservoirs are located within dense and highly heterogeneous strata, posing significant challenges for efficient exploitation with standard drilling equipment. Consequently, to enhance development of these reservoirs, research has been conducted using the liquid-pulsed discharge plasma technology to fracture rock formations. A key factor affecting this technology is the electrode part of the discharge structure. This paper focuses on the effects of three electrode parameters (electrode spacing, electrode shape, and electrode material) on the rock breaking technology by plasma liquid pulsed discharge . It is evidenced that changing the electrode parameters can effectively improve discharge characteristics and energy utilization, while reducing the technical cost, which has great development potential in unconventional reservoir reconstruction.
The Dina Cretaceous field, operated by Ecopetrol S.A., is situated in the basin of Colombia's Upper Magdalena Valley. Peripheral water injection started in 1985, reaching a peak oil production rate of about 10,000 BOPD in 1988. Subsequently, water production increased, leading to a decline in oil output, primarily due to reservoir heterogeneity and an unfavorable mobility ratio. Between 2011 and 2015, Colombia undertook its first pilot initiative using Colloidal Dispersion Gels (CDG) for in‑depth profile modification. This effort later evolved into a full‑field application between 2019 and 2022, translating into substantial advancement in implementing chemical conformance technologies. During the new waterflooding phase, water channeling in some injection patterns highlighted the need to address thief zones. To avoid this, a novel rigid gel (BG) formulation was proposed, which uses a higher polymer concentration than CDG and replaces aluminum citrate with chromium acetate, thereby ensuring more effective conformance control under reservoir conditions. The BG injection was successfully executed through the existing CDG facilities. Over eight days of injection and a four‑day shut‑in, the treatment improved vertical sweep efficiency, blocked water channeling, and increased contact with unswept zones. Results showed enhanced oil production, reduced water cuts, and changes in injectivity, which confirmed the effectiveness of alternating bulk gel injections for reservoir conformance control.