
The optimization of heating system has always been of much concern, among which the annual life cycle cost (ALCC) was widely used as an optimization method, while the non-guaranteed hours were often overlooked. This study proposed the elasticity-economy (E-E) objective function as an optimizing indicator, and demonstrated it taking a solar assisted heat pump heating system with phase change material (SC-ASHP-PCM) as an example. Firstly, the single variation impact was analyzed. After optimizing the thermal performance of sub-systems, the proportion of heat supplied by solar collector (SC) and phase change material (PCM) sub-systems increased by 5.4 % and 3.4 %, respectively. Subsequently, the Hooke-Jeeves algorithm was developed to optimize multifactors, hence minimizing the E-E objective function. The optimal solution was achieved when the nonguaranteed rate was 5 % and the penalty factor was 150 CNY/h. Compared with the baseline situation, the system energy consumption (156.8 x 10(3) kW.h) was reduced by 30 %, and the E-E objective function was reduced by 24 %. Furthermore, the minimum operating cost was 18.3 CNY/m(2), saving up to 46 % compared to traditional heating systems. The method is generalized to obtain the optimal energy saving potential under different non-guaranteed hours, which provides guidance for the heating systems' design and operation.
从19世纪开始,燃烧学的发展先后经历了燃烧热力学,燃烧反应动力学,燃烧物理学和反应流体力学等阶段.原来的燃烧理论只能定性地用于工程设计中.从20世纪70年代左右开始,由于大型数字计算机的产生和计算流体力学的出现,燃烧学发展到燃烧的数值模拟,先后出现了雷诺平均模拟、大涡模拟和直接数值模拟,可以把燃烧理论定量地用于燃烧装置的设计中.本文对燃烧学发展的几个里程碑进行了回顾,希望能和燃烧界同行们进行交流.
为提高某型燃气轮机的工作可靠性,对单晶涡轮叶片进行了强度分析与结构优化设计.采用第四强度理论,考虑了晶体取向、温度载荷、气动载荷和转速的影响,得到叶片的应力分布、典型截面的强度储备系数;根据诺顿蠕变方程计算关键节点的持久寿命;基于分析结果对叶片局部结构进行优化改进,将叶片质心向叶背侧偏移,调整进气前缘气膜孔的排列方式,并对新结构进行强度复算.结果表明:优化后的叶片静强度符合设计要求,消除了局部结构处的应力集中现象,叶身结构强度储备系数高于1.3,叶身两侧应力分布更加均匀,叶片在设计转速10%裕度范围内无共振现象发生.
中国国家开发投资有限公司(国投)冀能燃气发电有限公司已向GE Vernova订购了两台氢气燃气轮机,用于新建联合循环发电厂.这座1.7 GW的发电厂将位于中国浙江省舟山群岛,为中国最大的群岛供电,该群岛由1 390个岛屿组成.
设计并搭建了水平多管式相变储热系统,以水为传热流体(HTF)、石蜡为相变材料(PCM),通过实验对储热系统的具体蓄热特性和不同操作条件下HTF与PCM之间的传热特性进行定量分析,评估了 HTF体积流量和进口温度对紧凑型低温相变储热系统功率输入、吸热完成时间以及储存能量的影响.该系统主要由一个聚碳酸酯壳和水平定向的多管换热器以及石蜡组成,其中石蜡相变温度约为41℃.结果表明:随着HTF进口温度或体积流量的增加,吸热完成时间减少,平均吸热功率增大,且增加速率都随着进口温度的增大而变小;HTF体积流量分别为4.5,6.0和7.5 L/min时,吸热过程耗时300.7,252.9和226.7 min;在58,64和70 ℃的进口温度下,吸热完成时间分别为270.1,226.7和204.9 min;提高HTF进口温度,会导致换热结束时石蜡温度与HTF出口温度出现越来越靠近的趋势,而在提高HTF体积流量时,却呈现相反的趋势.