
The SWSRA-DS combined algorithm is proposed with the goal of sharing the near infrared analysis model of the holocellulose content of pulpwood on three different types of spectroscopic instruments. That is, the screening wavelengths based on spectrum ratio analysis (SWSRA) algorithm is used to select the wavelengths with good stability and consistency. These important wavelength variables, which are insensitive to the measured sample parameters, can reduce the differences in sample information response by different instruments or measurement conditions. Then the systematic errors that still existed after the SWSRA method calibration are further calibrated using the Direct Standardization (DS) method on the basis of these wavelengths. This combined algorithm can improve the generalizability of the master model, reduce the spectrum matrix dimension, and make the model transfer more stabilized and simple. The results show that the SWSRA-DS combined algorithm is able to reduce the RMSEP of the master model to predict the holocellulose content of samples measured on the target 1 and target 2 instruments from 2.01% and 9.45% to 0.96% and 1.08%, respectively. The SWSRA-DS algorithm result is compared with the calibration results of SWSRA and DS alone and the commonly used PDS and S/B model transfer algorithms to transfer performance is significantly improved, which provides a new idea for the sharing of NIR analysis models among different types of spectroscopic instruments.
Studying on superheated steam heat-treatment (SSHT) of resin can provides strong support for the research on wood drying and degreasing. Resin exudation remains a significant industry concern, limiting the environment in which pine lumber can be used. Hence, a two-stage SSHT was conducted on the resin, and the softening point (SP) and residual turpentine content (RTC) of the resin are determined by Thermomechanical analysis (TMA) and Thermogravimetric analysis (TGA). The effects of oxygen content and treatment time in the drying chamber on the removal efficiency of turpentine were also studied. Finally, the color of the heat-treated resin was measured, and the chemical composition of the heat-treated resin was analyzed by Fourier Transform Infrared Spectroscopy (FTIR) and X-ray photoelectronic spectroscopy (XPS). The results show that SSHT can remove turpentine from resin and increase the SP of resin, and the oxygen content significantly affects the removal efficiency of turpentine. The increase in the SP of the resin is due to the dehydrogenation, isomerization, and oxidation reactions of the resin caused by the heat-treatment. Therefore, the SSHT of resin can be adjusted and applied to the wood drying process to avoid resin exudation during the use of resinous wood products.
在竹建筑结构中,最常见的螺栓连接节点经常出现顺纹劈裂.通过试验研究了包裹玻璃纤维复合布材(glass fibre reinforced plastics,GFRP)后对于不同螺栓组合节点抗剪承载力的提升效果及加固后抗剪承载力的影响因素,以期为今后工程中竹结构螺栓组合节点的设计与应用提供参考.选取无裂缝无竹节的竹筒,制备单螺栓连接、双螺栓平行连接下的原竹螺栓组合节点试件,不加固组无处理,加固组采用GFRP包裹增强,用单轴压缩试验方法加载.比较加固前后组合节点和GFRP增强节点之间的等效抗剪强度和破坏模式,得出竹筒直径、螺栓直径、螺栓端距和根数对于GFRP增强效果和极限承载能力的影响.GFRP的包裹约束使得节点避免脆性开裂,屈服应力和等效抗剪强度分别提升5.84%~28.46%和7.59%~29.77%.GFRP加固对组合节点的等效抗剪强度提升效果与螺栓直径、竹筒外径、螺栓端距正相关,与螺栓根数没有显著关系.螺栓直径和竹筒外径是影响等效抗剪强度的主要因素.GFRP包裹增强的组合节点等效抗剪强度按照Johansen螺栓屈服模型拟合计算得到的误差平均绝对值为6.4%,在工程中可以用于简化计算.GFRP包裹能有效提升原竹螺栓组合节点的等效抗剪强度,使节点破坏模式由脆性开裂破坏变为延性受压破坏.螺径、螺栓根数、竹筒外径的增大能提升GFRP加固节点承载力和GFRP的承载力增强效果,螺栓端距增大对承载力无显著影响.GFRP加固节点的承载力可以通过螺栓屈服计算模型拟合而较为准确地预测.
以水稻秸秆为原料,接种娄彻氏链霉菌(Sireptomyces rochei),通过生物发酵和机械盘磨制备了秸秆纤维.利用电子万能试验机、接触角测量仪、荧光光谱仪、热重分析仪对不同目数的秸秆纤维及其成型材料的性能进行表征分析.试验结果表明:随着秸秆纤维尺寸的减小,纤维间的结合力逐渐增强,但需要更大的干燥强度.秸秆纤维的持水性和吸水性随着发酵时间的增加呈先增大后减小的趋势,随纤维增大吸水性呈升高趋势,但持水性随纤维的增大呈降低趋势.随着发酵时间的增加,秸秆纤维吸水性先逐渐降低,并且随烘干温度的升高接触角不断增大,在生物发酵7 d时成型材料水溶性有机物最多.烘干温度从150 ℃升高到190 ℃,抗张强度先增加后降低,纤维疏水性能逐渐增强;温度低于170 ℃时,抗张强度随温度升高不断增强,高于170℃则显著下降.接种娄彻氏链霉菌(Streptomyces rochei)发酵对秸秆纤维拆解具有促进效果,经生物发酵7 d和盘磨的秸秆纤维性能最佳,适宜于制备秸秆基质块.
超级电容器作为清洁可持续的储能设备,其电化学性能主要由电极材料决定,因此电极材料逐渐成为当前储能领域的研究热点.木材因其天然的多尺度微/纳米孔隙结构以及可再生、可生物降解等特点,逐渐被用于电极材料的研究.以巴沙木为基材,首先采用脱木素联合TEMPO氧化法将木材细胞壁分离具有纳米网络结构的木材气凝胶(TDW),然后将纳米纤维素分散的碳纳米管(CNT)悬浮液通过满细胞法浸渍到木材气凝胶中,冷冻干燥后在导管孔和细胞间隙中形成了连续的碳纳米管导电网络结构,最后进行聚吡咯(PPy)原位聚合,在细胞壁和导管孔中构建成具有纳米导电网络结构的TDW/CNT/PPy复合电极.电化学性能测试显示,由于在TDW的宏观孔隙中导电网络的构建,TDW/CNT/PPy的电化学性能明显优于TDW/PPy电极,而且随着碳纳米管比例的增加而增强,其中,TDW/CNT-2/PPy在1.0 mA/cm2扫描速率下的比电容达到389 F/g、面电容为10.5 F/cm2,而且在10 mA/cm2扫描速率下经过10 000次循环后的电容保持率为95.1%.本研究通过在木材中构建连续的导电纳米网络结构,显示出优异的电化学性能,为木质基材在电极材料中的应用提供了一种新的思路.