
To investigate the potential of modified epoxy resin for repairing and strengthening historical wooden structures, this study utilized polyurethane and silicone-modified epoxy resin as the base, alongside a polyamine curing agent. The resin mixture was cured at ambient temperature, resulting in the creation of ten unique epoxy resin systems. Investigation into the chemical structure and alterations to the glass transition temperature were conducted. The study conducted tests and characterization of viscosity, curing rate, mechanical properties, stress failure mode, hygrothermal aging resistance, and bonding properties. The results reveal that the curing degree of the two modified epoxy resins is high after being cured at room temperature, and the chemical structure and curing rate show insignificant changes. The range of the glass transition temperature for the modified epoxy resin is between 61.31 °C and 70.51 °C. The incorporation of polyurethane and silicone molecular chains into the epoxy resin cross-linking curing system enhances the toughness of the epoxy resin. The modified resin achieves a maximum elongation at break that is 5.18 times greater than that of the unmodified resin, along with a maximum tensile strength and a compressive strength that are 7.94 and 1.74 times, respectively, higher than those in the Chinese technical specifications for the maintenance and reinforcement of ancient wooden structures. The increase in toughness changes the failure mode of the cured epoxy resin. The modified epoxy resin exhibits great bonding ability to aged wood, with a shear strength of up to 9.6 MPa along the grain. As a result, the modified epoxy resin meets the requirements for the reinforcement and repair of the timber members of ancient buildings.
选择4种常用进口树种实木地板坯料和1种国产树种实木地板坯料,利用木材常规干燥试验机进行兼顾杀虫(D工艺)、灭菌(S工艺)的热湿平衡处理,检测分析其终含水率、厚度上的含水率偏差、残余应力、可见缺陷等指标变化.结果表明:地板坯料的质量在不同树种、同一批次内均存有差异.本研究中制定的D工艺(65℃/相对湿度73.8%~89.5%)、S工艺(75℃/相对湿度76.7%~91.2%)两个等级,可满足地板坯料杀虫、灭菌的加热技术要求,同时可降低地板坯料内和坯料间的最大含水率偏差,提高含水率均匀度,降低厚度上的含水率偏差,降低残余应力值,且对可见缺陷的影响不明显.热湿平衡处理坯料的质量符合LY/T 2058-2022《实木地板坯料》或GB/T 6491-2012《锯材干燥质量》中二级材的要求.
机器视觉技术可实现物体尺寸的快速、非接触式检测,替代人工测量家具板件尺寸,解决测量效率低、连续性差等问题.本研究基于激光线阵相机与线结构光测量技术,构建一种适用于家具板件的三维尺寸在线测量系统,并分析该系统的测量精度与效率.家具板件在传送装置上以300 mm/s的速度作匀速运动,经过650 nm激光器照射的激光三角平面时,互补金属氧化物半导体(complementary metal oxide semiconductor,CMOS)传感器对家具板件表面反射的激光进行成像;使用锯齿靶标法标定,应用机器视觉软件Halcon读取相机标定文件和激光线阵相机生成的家具板件信息图像,经过图像处理,完成家具板件三维尺寸测量.结果表明:系统测量的板件厚度、宽度和长度,相对人工测量结果,最大偏差率分别为3.6%、0.5%和0.1%;对照QB/T 4452-2013《木家具 极限与配合》标准要求,测量的厚度最大差值小于IT15级公差值(<0.70 mm),宽度最大差值小于IT14级公差值(<1.00 mm),长度最大差值小于IT12级公差值(<0.90 mm).单件测量用时由人工测量的30.1 s缩短至5.5 s,表明系统的测量精度与效率优势.
为提高木塑复合材料(wood-plastic composites,WPCs)的力学性能,基于酯交换反应,以木粉、E51环氧树脂和邻苯二甲酸酐为原料,通过热压成型工艺制备热可逆性共价交联木塑复合材料(TRC-WPCs),探究环氧与酸酐量比、热压工艺参数和循环加工对TRC-WPCs力学性能的影响.当环氧与酸酐的量比为1∶1,热压时间为30 min、热压温度为150℃、热压压力为12 MPa时,TRC-WPCs的力学性能最优,其拉伸强度、拉伸模量、弯曲强度和弯曲模量分别为47.3 MPa、9.3 GPa、79.2 MPa和8.9 GPa,比相同木粉含量的高密度聚乙烯基WPCs高出282%、204%、305%和245%;且循环加工后其弯曲强度和弯曲模量保持率为67.8%和84.2%,实现了TRC-WPCs的高强度化,并且高温下可循环加工.
为减缓改性脲醛树脂与面粉调配后黏度快速升高对胶合板淋胶工艺施胶均匀性的影响,本研究提出利用含疏水结构分子的乙二醇油酸酯、三油酸甘油酯和吐温-80削弱调配胶液组分间缔合作用,控制胶液黏度,并探讨含疏水结构分子对胶液黏度及其变化速率以及胶合强度的影响.结果表明,非离子型表面活性剂类含疏水结构分子的吐温-80添加量为胶液质量的1.6%时,胶液黏度由4 039 mPa·s降低至3 429 mPa·s,且在调配后0.5~5.5 h内,胶液黏度平均增加速率相比对照组降低74%.非离子型表面活性剂类含疏水结构分子的亲水端保障其在胶液体系中均匀分散,疏水端有效削弱胶液组分间缔合作用;适当添加非离子型表面活性剂类含疏水结构分子,可提高胶合板的胶合强度,但添加过量时,会降低胶合板的胶合强度.