
The results of the investigation and develop of the suppressing additive noise methods in fiber-optic interferometric sensors, in which optical scheme is based on a two-beam Michelson interferometer, are presented. The proposed solutions are designed to reduce the level of additive noise and to increase the signal-to-noise ratio in the fiber-optic interferometric sensor phase signal. The first proposed method assumes the insertion of an additional photodetector into the optical scheme of the sensor, which allows simultaneous registration of the same interference signal twice. In the optical scheme of the second proposed method, an additional fiber delay line is included, which allows to interrogate the same sensor twice. Mathematical analysis based on the coherent averaging of signals is applied for the suppressing of the additive noises. Coherent averaging of signals allows, without changing the useful component of the phase signal, to reduce the additive noise level by the value which is proportional to the square root of the averaged signals number. The experimental study of the proposed suppressing additive noise methods presented a decrease of the noise level by factor of 1.4 and an increase of the signal-to-noise ratio on an average by 2.87 dB in the frequency range from 250 to 2250 Hz in the phase signal of the fiber-optic interferometric sensor. The proposed methods of the suppressing additive noise can be used to increase the signal-to-noise ratio in fiber-optic measuring systems based on the interferometric sensors arrays, such as fiber-optic towed and bottom seismic streamers, perimeter security systems, fiber-optic navigation systems and complexes.
This work demonstrates for the first time the selectivity of silver molecular clusters luminescence in silicate glass formed by the ion exchange method from a salt melt containing 0.1 mol.% silver nitrate (AgNO3) and 99.9 mol.% sodium nitrate (NaNO3). Commercial silicate microscope slides of the following system were used: SiO2-Na2O-K2O-CaO-MgO-Al2O3 with Fe2O3-SO3 impurities. Molecular clusters were obtained by low-temperature ion exchange in a melt of 0.1 % AgNO3/99.9 % NaNO3 mol.% for 10 and 15 min at 320 °C. The luminescent properties of silver molecular clusters in the ion-exchange layer of microscope slides were studied. Bands of silver clusters of different sizes (Ag1-5) were found in the luminescence spectra. In this case, clusters Ag1-3 are excited by shorter wavelengths, and clusters Ag4-5 only by far ultraviolet and visible radiation up to 500 nm. In the process of ion exchange lasting up to 10 minutes, the appearance of luminescence selectivity was revealed, which occurs due to the presence of a low concentration of silver clusters of different sizes Ag1-5 in the ion-exchange layer. The obtained results can be used in the development of a photosensitive element for a selective ultraviolet radiation detector.
Evidence-based technologies for product quality have a positive impact on a wide range of social and economic processes. One of the immanent problems of implementing such technologies is determined by the contradiction between the need to ensure open access to information about the stages of the technological process and the confidentiality of some of such data. The use of strict cryptographic procedures to resolve this contradiction is often impossible due to resource constraints, in particular, the lack of continuous telecommunications between the parties involved. The results obtained are aimed at ensuring the feasibility of product quality traceability systems under resource constraints. They are based on a new architectural solution and the integration of classical methods and tools to ensure information security. The paper proposes a three-level model of a product quality traceability system with controlled quality degradation and scenarios for ensuring the continuity of its safe operation. The basic concepts of the proposed solution are: separation of stored data into publicly available and confidential; procedures for “deferred” trusted access in conditions where direct communication with one of the data owners is impossible; data separation into shards — functionally or geographically localized data warehouses; immanent properties of distributed registry systems in terms of ensuring data integrity and availability, non-repudiation of operations. The paper introduces typical scenarios for the use of a hierarchical product quality tracking system, sets and proposes a solution to the problem of ensuring information security of their implementation. The approach to reducing the level of information security of specific implementations in conditions of resource constraints is justified by taking into account the specifics of the functioning of application systems. The information security of the new results is confirmed by computer modeling using specialized protocol security analysis tools. Unlike well-known models focused on the use of stable communication channels, centralized data models, strict cryptographic algorithms and significant computing resources that do not involve accessing data in the absence of communication with their owner, the proposed solution provides authenticated controlled access to the requested confidential data and in the absence of communication with their owner. An immanent disadvantage of the implementation of the discussed scenarios is a certain decrease in the level of information security associated with delegating trust to a third party as well as simplifying the compromise of distributed registry shard nodes.
Weight sensors are widely used in the freight transportation industry. In the systems for weighing vehicles while moving, ceramic, polymer, quartz piezoelectric sensors, load or hydraulic cells, strain gauges are used as sensitive elements. However, most electric sensors are susceptible to electromagnetic interference. Currently, fiber-optic sensors are most actively developed and put into operation due to their relatively low cost, small weight and size parameters, high measurement accuracy and complete passivity to electromagnetic disturbances. Fiber-optic sensors are most often implemented using fiber Bragg gratings, taking into account the convenience of their multiplexing. Mechanical deformations lead to a shift in the wavelength of the Bragg resonance of the grating. At the same time, the problem of using fiber gratings is associated with their sensitivity to temperature. To achieve high accuracy in measuring the deformation value, and accordingly, the weight characteristics of the object, it is necessary to eliminate or compensate for the effect of the sensor temperature on its readings. Most modern studies describe sensors that either operate in laboratory conditions or involve the use of an additional sensor that complicates the circuit for measuring temperature. The paper proposes a method for solving the problem of cross-sensitivity of a fiber diffraction structure to temperature and deformation. The method is based on the use of a pair of closely spaced gratings in the sensitive element of the sensor. One of the gratings has a constant period along the length, and the other has a variable one. The design of the sensitive element ensures the transfer of mechanical load only to the fiber grating with a constant period, and the temperature change equally affects both diffraction structures. A design solution for the sensitive element is proposed that allows for temperature effects compensation without using additional elements. A mathematical model of temperature effects is presented, allowing estimating the dependence of the temperature gradient on time for different thicknesses of the sensitive element. Modeling has showed that for a sample 0.95 cm thick, the temperature gradient inside the substrate is insignificant. With a sharp change in temperature, the equalization of the temperature field within the substrate at a level of 90 % occurs in no more than 2.5 s. The mechanical load on the sensitive element can pass relative to the fiber grating at different angles in connection with which the value of the shift of the central wavelength of the Bragg resonance was studied in detail depending on the point of application and direction of the load. The proposed technology may be of interest in the development and operation of automatic weight and size control systems with temperature compensation without the use of additional sensors. The proposed system is easy to operate and it has a low cost.
A method for compensating for the constant noise component of reflectograms for a coherent optical backscatter reflectometer in the time domain is proposed. The presented solution ensures correct visualization of reflectograms, improves their readability and allows recording weak reflected signals from a fiber communication line. The experimental testing of the method was carried out on a working sample of a coherent optical reflectometer. To compensate for the constant component of reflectogram noise, it is proposed to record the noise signal from the input path of the reflectometer immediately before sending the optical probing signal to the communication line. The data obtained in this way do not contain a useful signal from the connection line. In this case, the data can be used to determine the constant component of the noise level by calculating its root mean square value. Compensation for the constant noise level is performed by subtracting the constant component of the noise from the data of the entire reflectogram. The described method was tested on a working sample of a coherent optical reflectometer developed at the Light-Guided Photonics Research Center of ITMO University. The technique was tested on two test fiber lines: a 200-km-long optical fiber and a 300-km-long line with three optical amplifiers. It was shown that the application of the technique allows to significantly expand the dynamic range of signals presented on reflectograms by more than 10 dB and to increase the distinguishability of weak signals at the noise level of the device. The practical significance of the work lies in the possibility of compensating for the constant component of noise in the reflectogram of a fiber-optic communication line with optical amplifiers without calibrations and preliminary settings of the coherent optical reflectometer.