This review summarizes recent advances in micro- and nanopore technologies with a focus on the functionalization of pores using a promising method named contactless electro-functionalization (CLEF). CLEF enables the localized grafting of electroactive entities onto the inner wall of a micro- or nano-sized pore in a solid-state silicon/silicon oxide membrane. A voltage or electrical current applied across the pore induces the surface functionalization by electroactive entities exclusively on the inside pore wall, which is a significant improvement over existing methods. CLEF's mechanism is based on the polarization of a sandwich-like silicon/silicon oxide membrane, creating electronic pathways between the core silicon and the electrolyte. Correlation between numerical simulations and experiments have validated this hypothesis. CLEF-induced micro- and nanopores functionalized with antibodies or oligonucleotides were successfully used for the detection and identification of cells and are promising sensitive biosensors. This technology could soon be successfully applied to planar configurations of pores, such as restrictions in microfluidic channels.

Food safety is a public health challenge. Devices allowing early, fast, label-free and in situ detection of bacteria are of great interest to prevent outbreaks. Listeria monocytogenes, Salmonella spp. and Escherichia coli O157:H7 are foodborne pathogens which were responsible of 60% of the hospitalizations in the USA in 2011. In this study, we conceived a carbohydrate microarray in order to detect and discriminate these three food pathogenic bacteria. In less than 10 hours, from an initial bacterial suspension of 100 bacteria per mL, Surface Plasmon Resonance imaging allowed the detection and the discrimination of these bacteria while they were growing and interacting specifically with the carbohydrate microarray. Moreover, this device is easily regenerable and can be re-used: it is probably a promising tool to early detect bacteria in food.

Prevention of foodborne diseases depends highly on our ability to control rapidly and accurately a possible contamination of food. So far, standard procedures for bacterial detection require time-consuming bacterial cultures on plates before the pathogens can be detected and identified. We present here an innovative biochip, based on direct differential carbohydrate recognitions of five closely related Escherichia coli strains, including the enterohemorragic E. coli O157:H7. Our device relies on efficient grafting of simple carbohydrates on a gold surface and on the monitoring of their interactions with bacteria during their culture using surface plasmon resonance imaging. We show that each of the bacteria interacts in a different way with the carbohydrate chip. This allows the detection and discrimination of the tested bacterial strains in less than 10 h from an initial bacterial concentration of 10(2) CFU·mL(-1). This is an improvement over previously described systems in terms of cost, easiness to use, and stability. Easily conceived and easily regenerated, this tool is promising for the future of food safety.

Human cysteine cathepsin S (catS) participates in distinct physiological and pathophysiological cellular processes and is considered as a valuable therapeutic target in autoimmune diseases, cancer, atherosclerosis, and asthma. We evaluated the capacity of negatively charged glycosaminoglycans (heparin, heparan sulfate, chondroitin 4/6-sulfates, dermatan sulfate, and hyaluronic acid) to modulate the activity of catS. Chondroitin 4-sulfate (C4-S) impaired the collagenolytic activity (type IV collagen) and inhibited the peptidase activity (Z-Phe-Arg-AMC) of catS at pH 5.5, obeying a mixed-type mechanism (estimated Ki = 16.5 ± 6 μM). Addition of NaCl restored catS activity, supporting the idea that electrostatic interactions are primarly involved. Furthermore, C4-S delayed in a dose-dependent manner the maturation of procatS at pH 4.0 by interfering with the intermolecular processing pathway. Binding of C4-S to catS was demonstrated by gel-filtration chromatography, and its affinity was measured by surface plasmon resonance (equilibrium dissociation constant Kd = 210 ± 40 nM). Moreover, C4-S induced subtle conformational changes in mature catS as observed by intrinsic fluorescence spectroscopy analysis. Molecular docking predicted three specific binding sites on catS for C4-S that are different from those found in the crystal structure of the cathepsin K-C4-S complex. Overall, these results describe a novel glycosaminoglycan-mediated mechanism of catS inhibition and suggest that C4-S may modulate the collagenase activity of catS in vivo.

A synthetic redox probe structurally related to natural pyridoacridones was designed and electrochemically characterised. These heterocycles behave as DNA intercalators due to their extended planar structure that promotes stacking in between nucleic acid base pairs. Electrochemical characterization by cyclic voltammetry revealed a quasi-reversible electrochemical behaviour occurring at a mild negative potential in aqueous solution. The study of the mechanism showed that the iminoquinone redox moiety acts similarly to quinone involving a two-electron reduction coupled with proton transfer. The easily accessible potential region with respect to aqueous electro-inactive window makes the pyridoacridone ring suitable for the indirect electrochemical detection of chemically unlabelled DNA. Its usefulness as electrochemical hybridization indicator was assessed on immobilised DNA and compared to doxorubicin. The voltamperometric response of the intercalator acts as an indicator of the presence of double-stranded DNA at the electrode surface and allows the selective transduction of immobilised oligonucleotide hybridization at both macro- and microscale electrodes.

The use of biological-probe-modified solid-state pores in biosensing is currently hindered by difficulties in pore-wall functionalization. The surface to be functionalized is small and difficult to target and is usually chemically similar to the bulk membrane. Herein, we demonstrate the contactless electrofunctionalization (CLEF) approach and its mechanism. This technique enables the one-step local functionalization of the single pore wall fabricated in a silica-covered silicon membrane. CLEF is induced by polarization of the pore membrane in an electric field and requires a sandwich-like composition and a conducting or semiconducting core for the pore membrane. The defects in the silica layer of the micropore wall enable the creation of an electric pathway through the silica layer, which allows electrochemical reactions to take place locally on the pore wall. The pore diameter is not a limiting factor for local wall modification using CLEF. Nanopores with a diameter of 200 nm fabricated in a silicon membrane and covered with native silica layer have been successfully functionalized with this method, and localized pore-wall modification was obtained. Furthermore, through proof-of-concept experiments using ODN-modified nanopores, we show that functionalized nanopores are suitable for translocation-based biosensing.

The polypyrrole approach initially developed for the construction of DNA chips, has been extended to other biochemical compounds such as proteins and more recently oligosaccharides. The copolymerization of a pyrrole monomer with a biomolecule bearing a pyrrole group by an electrochemical process allows a very fast coupling of the biomolecule (probe) to a gold layer used as a working electrode. Fluorescence-based detection is the reference method to detect interactions on biochips; however an alternative label free method, could be more convenient for rapid screening of biointeractions. Surface Plasmon Resonance (SPRi) is a typical label-free method for real time detection of the binding of biological molecules onto functionalized surfaces. This surface sensitive optical method is based upon evanescent wave sensing on a thin metal layer. The SPR approach described herein is performed in an imaging geometry that allows simultaneous monitoring of biorecognition reactions occurring on an array of immobilized probes (chip). In a SPR imaging experiment, local changes in the reflectivity are recorded with a CCD camera and are exploited to monitor up to 100 different biological reactions occurring onto the molecules linked to the polypyrrole matrix. This method will be applied to oligosaccharide recognition.

Diamond received tremendous interest for analytical sciences due to its intrinsic properties. However, the analytical perception of chemical environment requires surface functionalization that brings selectivity to the detection event. Thereby, many works focused on diamond modification using chemical or biochemical entities. We proposed here, a new and straightforward methodology for diamond (bio) functionalization. This method involves the chemical reaction between (bio) chemical entities presenting a primary amine moiety, used as grafting site, and hydrogenated diamond surface. This reaction allows in one step to modify diamond surface whatever its doping level and its crystalline quality. The effectiveness of this new method is exposed here through the grafting of one redox species, ferrocene, and of one biochemical, biotin. The impacts of both functionalization duration and pH are investigated and the robustness of the formed bond is demonstrated owing to biotin-avidin coupling.

Blood is a tremendous source of data for diagnostic purposes. Thanks to the qualitative and quantitative analysis of the different cell types carried into the blood stream. To that end, cell capture of several cell types at different locations on a microarray is an interesting alternative to classical techniques run ‘in solution’ as it allows simultaneous characterization of several cells on a single device. In this chapter, we have described a method based on the production of antibody microarrays specific to two different cell types: B and T lymphocytes. We have also described the real-time monitoring of the cell capture on the microarray using surface plasmon resonance imaging (SPRi).

Nowadays, high-throughput analysis of biological events is a great challenge which could take benefit of the recent development of microarray devices. The great potential of such technology is related to the availability of a chip bearing a large set of probes, stable and easy to obtain, and suitable for ligand-binding detection. Here, we describe a new method based on polypyrrole chemistry, allowing the covalent immobilization of peptides in a microarray format and on a gold surface compatible with the use of surface plasmon resonance. This technique is then illustrated by the detection and characterization of antibodies induced by hepatitis C virus and present in patients' serums.

In order to construct tools able to screen oligosaccharideprotein interactions, we have developed a polypyrrolebased oligosaccharide chip constructed via a copolymerization process of pyrrole and pyrrole-modified oligosaccharide. For our study, GAG (glycosaminoglycans) or GAG fragments, which are involved in many fundamental biological processes, were modified by the pyrrole moiety on their reducing end and then immobilized on the chip. The parallel binding events on the upperside of the surface can be simultaneously monitored and quantified in real time and without labeling by surface plasmon resonance imaging (SPRi). We show that electrocopolymerization of the oligosaccharide-pyrrole above a gold surface enables the covalent immobilization of multiple probes and the subsequent monitoring of their binding capacities using surface plasmon resonance imaging. Moreover, a biological application was made involving different GAG fragments and different proteins, including stromal cell-derived factor-1 alpha (SDF-1 alpha), interferon-gamma (IFN-gamma), and monoclonal antibody showing different affinity pattern.

Initially developed for the construction of DNA chips, the polypyrrole approach has been extended to other biochemical compounds (mainly proteins and oligosaccharides). This method allows one to copolymerize a pyrrole monomer with a biomolecule bearing a pyrrole group; this reaction is based on an electrochemical process allowing a very fast coupling of the biomolecule (probe) to a gold layer used as a working electrode. Fluorescence-based detection processes are classically used for evidence biorecognition on biochips; in order to avoid the labeling of the targets, we propose an alternative method—surface plasmon resonance imaging (SPRi). Surface plasmon resonance (SPR) is a typical label-free method for real-time detection of the binding of biological molecules onto functionalized surfaces. This surface-sensitive optical method is based upon evanescent wave sensing on a thin metal layer. The SPR approach described herein is performed in an imaging geometry that allows simultaneous monitoring of biorecognition reactions occurring on an array of immobilized probes (chip). In a SPRi experiment, local changes in reflectivity are recorded with a charge-coupled device (CCD) camera and are exploited to monitor up to 100 different biological reactions occurring on the molecules linked to the polypyrrole matrix. This method will be applied to protein recognition.

Initially developed for the construction of DNA chips, the polypyrrole approach has been extended to other biochemical compounds (mainly proteins and oligosaccharides). This method allows one to copolymerize a pyrrole monomer with a biomolecule bearing a pyrrole group; this reaction is based on an electrochemical process allowing a very fast coupling of the biomolecule (probe) to a gold layer used as a working electrode. Fluorescence-based detection processes are classically used for evidence biorecognition on biochips; in order to avoid the labeling of the targets, we propose an alternative method--surface plasmon resonance imaging (SPRi). Surface plasmon resonance (SPR) is a typical label-free method for real-time detection of the binding of biological molecules onto functionalized surfaces. This surface-sensitive optical method is based upon evanescent wave sensing on a thin metal layer. The SPR approach described herein is performed in an imaging geometry that allows simultaneous monitoring of biorecognition reactions occurring on an array of immobilized probes (chip). In a SPRi experiment, local changes in reflectivity are recorded with a charge-coupled device (CCD) camera and are exploited to monitor up to 100 different biological reactions occurring on the molecules linked to the polypyrrole matrix. This method will be applied to protein recognition.

The greatest challenge in the postgenomic era is the description of proteome interactions, such as protein–protein or protein–DNA interactions. Surface plasmon resonance (SPR) is an optical technique in which binding of an analyte to the surface changes the refractive index at the surface/solution interface. Molecular interactions are analysed in real time without a labeling step. Currently, the limit to SPR imaging is the small number of reactions that can be simultaneously analysed. Using a novel grafting technology and a new imaging system, we increased the throughput of SPR imaging. The interaction between p53 and DNA was chosen as a paradigm for validation of this assay. Using a tagged DNA methodology, we simultaneously targeted multiple DNA sequences on a single chip. The interaction between p53 and these DNA sequences was monitored by SPR imaging. Qualitative and quantitative analysis provides results similar to those obtained with conventional technologies.

Le but de la presente invention est de fournir un procede de fixation d'une proteine sur un polymere conducteur, utilisable notamment pour la fabrication d'un capteur ou d'un multicapteur, par exemple d'une biopuce. Ce but, et d'autres encore, sont atteints, conformement a l'invention, par un procede de fixation d'une proteine sur un polymere du pyrrole comprenant les etapes suivantes : couplage de la proteine a fixer avec du pyrrole de maniere a obtenir une premiere solution d'un compose de couplage proteine-pyrrole, preparation d'une deuxieme solution de pyrrole ne contenant pas la proteine, melange de ladite premiere solution avec ladite deuxieme solution pour obtenir une solution d'electropolymerisation, electropolymerisation du pyrrole et de la proteine couplee au pyrrole sur un support conducteur a partir de ladite solution d'electropolymerisation.

We have electrosynthesized a hydrophilic biotinylated polypyrrole film and studied it by gravimetric measurements using a quartz crystal microbalance (QCM). We demonstrated that the quantity of immobilized avidin is a function of the number and the accessibility of biotin units in the polypyrrole film. From QCM results, it appears that the amount of anchored avidin could be modulated by the quantity of biotin units inserted in the polypyrrole matrix and also by the spacer arm length linking biotin units to the polypyrrole network. For this last case, the coverage rate in avidin could vary from 8 to 16 pmol cm−2.

Biosensors based on electronic conducting polymers appear particularly well suited to the requirements of modern biological analysis—multiparametric assays, high information density, and miniaturization. We describe a new methodology for the preparation of addressed DNA matrices. The process includes an electrochemically directed copolymerization of pyrrole and oligonucleotides bearing on their 5′ end a pyrrole moiety. The resulting polymer film deposited on the addressed electrode consists of pyrrole chains bearing covalently linked oligonucleotides (ODN). An oligonucleotide array was constructed on a silicon device bearing a matrix of 48 addressable 50 × 50 µm gold microelectrodes. This technology was successfully applied to the genotyping of hepatitis C virus in blood samples. Fluorescence detection results show good sensitivity and a high degree of spatial resolution. In addition, gravimetric studies carried out by the quartz crystal microbalance technique provide quantitative data on the amount of surface-immobilized species. In the case of ODN, it allows discrimination between hybridization and nonspecific adsorption. The need for versatile processes for the immobilization of biological species on surfaces led us to extend our methodology. A biotinylated surface was obtained by coelectropolymerization of pyrrole and biotin-pyrrole monomers. The efficiency for recognition (and consequently immobilization) of R-phycoerythrin-avidin was demonstrated by fluorescence detection. Copolymerization of decreasing ratios of pyrrole-biotin over pyrrole allowed us to obtain a decreasing scale of fluorescence.

Two strategies of DNA biochip construction on conducting polymers are investigated. The first involves a direct electro-copolymerization of pyrrole–oligonucleotides (oligonucleotides tethered to a pyrrole group) with the pyrrole leading to a polypyrrole film bearing the oligonucleotides. Successive copolymerizations allow the transformation of a microelectrode array into a DNA array. The second methodology involves a direct in situ synthesis of oligonucleotides on a conducting polymer used as an organic electrode. In this way a 5′ electrolabile protecting group, p -nitrobenzoyl, was used. In order to construct short oligonucleotide sequences, the other protecting groups of the bases have also to be modified. Preliminary results based on this technology are shown.