Low-level jets (LLJs) describe conditions in which the wind speed reaches a local maximum with respect to altitude near the surface; they have been observed intermittently in the US mid-Atlantic offshore environment. LLJs pose unique operating conditions for future wind turbines operating in the region, such as negative shear and locally strong veer, but they are not typically considered in existing turbine standards. This work builds upon recent research that explains the formation and evolution of the US mid-Atlantic LLJs through a simple analytical governing equation. We generate several LLJ inflow conditions with varying jet characteristics based on this analytical model and create monotonically sheared (MS) analogues with matched veer to assess the impacts of the LLJ on turbine performance and loading. Using aeroelastic simulations with these inflow conditions on the International Energy Agency 15-MW reference turbine, we find that the LLJ leads to a greater range of tower-top pitching and yawing moments, which could contribute to larger accumulated structural fatigue in components compared to MS inflow. These preliminary results demonstrate a path toward a unified set of test cases for low-level wind maxima that can inform the International Electrotechnical Commission standards related to offshore wind turbine design.

ABSTRACT This paper presents the acausal modeling, validation, and control of floating offshore wind turbines (FOWTs). The model simulates the IEA‐15 MW reference turbine and the semi‐submersible VolturnUS‐S platform utilizing a Control‐oriented, Reconfigurable, and Acausal Floating Turbine Simulator (CRAFTS), which integrates the key coupled aero‐hydro‐elasto‐servo dynamics and is being developed by authors at the University of Central Florida. Verification and validation are conducted using numerical data from the industry‐standard simulation platform OpenFAST and experimental data from the Floating Offshore‐wind and Controls Advanced Laboratory (FOCAL) project, in which the authors were involved. Numerical results demonstrate the model's ability to qualitatively capture loads and responses across various load cases, highlighting the impact of the control system under different wind and wave conditions and opening new opportunities for optimizing FOWT designs. This paper provides wind turbine researchers with valuable insights into system characteristics, system frequencies, damping effects, and internal reaction forces, serving as a reference for future studies in FOWT modeling and control.

This paper presents the modeling and verification of multibody structural dynamics for offshore wind turbines. The flexible tower and support structure of a monopile-based offshore wind turbine are modeled using an acausal, lumped-parameter, multibody approach that incorporates structural flexibility, soil-structure interaction, and hydrodynamic models. Simulation results are benchmarked against alternative modeling approaches, demonstrating the model's ability to accurately capture both static and dynamic behaviors under various wind and wave conditions while maintaining computational efficiency. This work provides a valuable tool for analyzing key structural characteristics of wind turbines, including eigenfrequencies, mode shapes, damping, and internal forces.

The dynamic behaviour of floating offshore wind turbines (FOWTs) involves complex interactions of multivariate loads from wind, waves, and currents, which result in complex motion characteristics. Although methods for analysing global motion responses are well-established, the time- and location-dependent kinematics remain underexplored. This paper investigates the instantaneous centre of rotation (ICR), a point of zero velocity at a time instance of general plane motion. Understanding and strategically positioning the ICR can reduce the dynamic motion in critical structural locations, enhancing the performance and structural robustness of FOWTs. The paper presents a method for computing the ICR using time-domain simulation results and proposes a statistical analysis approach suitable for design studies. Building on prior research, it examines the sensitivity of the ICR to external loading and design features, providing insights into how these factors influence motion response and how the motion response influences the statistics of the ICR, structural loads, and other performance metrics of interest. The study explores two FOWT configurations, a spar and a semisubmersible, identifying design variables that most effectively control the ICR statistics and identifying the ICR statistics most correlated with the responses of interest. Finally, through two case studies, we demonstrate how to apply these new insights in a practical design scenario. By adjusting the design variables most correlated with the ICR (fairlead vertical position and centre of mass for the spar and mooring line length and offset column diameter for the semisubmersible), we successfully modified the designs of the floating support structures to reduce the loads in the mooring lines, tower base, and blade roots, improving the ultimate strength and fatigue characteristics compared to the original designs.

To advance the control co-design of offshore wind energy systems, the authors perform basin-scale experiments with a fully instrumented and actuated floating offshore wind turbine model. The model consists of a 1:70 scale performance-matched model of the International Energy Agency Wind Technology Collaboration Programme 15-MW reference turbine atop the VolturnUS-S semisubmersible platform. The Reference OpenSource Controller provides real-time blade pitch and generator torque control. We aim to develop an open data set for the validation of numerical models in predicting the influence of turbine control and load-mitigation measures. For this purpose, we measure the effects of advanced turbine control features, including peak shaving and floating feedback as well as hull-based control using tuned mass dampers on the system. Overall, the results demonstrate measurable and consistent influences from the control and load-mitigation measures, thus confirming the usefulness as a validation data set. Peak shaving attenuates the response to wind turbulence at near-rated wind speed. Floating feedback reduces the load and platform pitch motion associated with the negative damping induced by blade pitch control. The tuned mass dampers also attenuate the system response near the targeted frequencies under suitable conditions. We also identify detrimental side effects of each load-mitigation measure.

Wind and marine energy are rapidly growing and complementary technologies that share some techniques for simplified modeling and control, particularly in below-rated flow speeds. A turbine operator has several choices of controller for maximizing power in Region 2. The simple and ubiquitous K Omega(2) control law is often effective but limited in its flexibility. Alternative controllers use reference tracking to split the control objectives into a low-bandwidth optimal tip-speed ratio tracking loop to maximize steady-state power and a higher-bandwidth proportional-integral control loop to reject inflow turbulence. Several options exist for identifying the slowly varying optimal set point during operation, based on estimating the inflow velocity or filtering the power or torque signals. This study compares the trade-offs between performance and other design priorities for a few choices of reference-tracking controller in the literature for reference wind and marine turbines. Analysis is performed in the frequency domain using the linearization of each controller, and the impact of turbulent disturbances on the closed-loop system is described. The controllers are simulated in OpenFAST to analyze their performance with higher-order nonlinear turbine dynamics.

Several control co-design (CCD) optimizations of floating offshore wind turbines are presented in this work using the newly introduced Wind Energy with Integrated Servo-Control (WEIS) framework. Three methods for parameterizing the primary tuning inputs to the Reference Open-Source Controller are presented and optimized, including a sensitivity-margin constrained controller. WEIS, a detailed, open-source floating offshore wind turbine design optimization tool is then used to conduct CCD optimizations on the International Energy Agency (IEA) 15MW wind turbine on the University of Maine VolturnUS-S semisubmersible platform. The results from optimizations are shown to reduce the levelized cost of energy (LCOE) by approximately 1% and 4% when optimizing the tower and platform, respectively. It is also found that the coupling between the tower and control system parameters is weaker than the coupling between the floating system and control system parameters, showing that CCD may not be advantageous for certain problems. Finally, a subset of operational design load cases is run to verify the optimized controller and turbine models.

This article presents a validation study of the popular aeroservoelastic code suite OpenFAST leveraging weeks of measurements obtained during normal operation of a 2.8 MW land-based wind turbine. Measured wind conditions were used to generate one-to-one turbulent flow fields (i.e., comparing simulation to measurement in 10 min increments, or bins) through unconstrained and constrained assimilation methods using the kinematic turbulence generators TurbSim and PyConTurb. A total of 253 bins of 10 min of normal turbine operation were selected for analysis, and a statistical comparison in terms of performance and loads is presented. We show that successful validation of the model was not strongly dependent on the type of inflow assimilation method used for mean quantities of interest, which had median modeling errors per wind-speed interval generally within 5 %–10 % of the measurement. The type of inflow assimilation method did have a larger effect on the fatigue predictions for blade-root flapwise and tower-base fore–aft quantities, which surprisingly saw larger errors from the assumed higher-fidelity assimilation methods. Avenues for further work are discussed and include possible improvements to the aerodynamic, structural, and controller modeling that may offer insight on the origin of the up to ∼ 40 % median overprediction of fatigue for these quantities.

Wind energy is recognized worldwide as cost-effective and environmentally friendly, and it is among the fastest-growing sources of electrical energy. To further decrease the cost of wind energy, wind turbines are being designed at ever-larger scales. To expand the deployment of wind energy, wind turbines are also being designed on floating platforms for placement in deep-water locations offshore. Both larger-scale and floating wind turbines pose challenges because of their greater structural loads and deflections. Complex, large-scale systems such as modern wind turbines increasingly require a control co-design approach, whereby the system design and control design are performed in a more integrated fashion. This article reviews recent developments in control co-design of wind turbines. We provide an overview of wind turbine design objectives and constraints, issues in the design of key wind turbine components, modeling of the wind turbine and environment, and controller coupling issues. Wind turbine control functions and the integration of control design in co-design are detailed with a focus on co-design compatible control approaches. Expected final online publication date for the Annual Review of Control, Robotics, and Autonomous Systems, Volume 7 is May 2024. Please see http://www.annualreviews.org/page/journal/pubdates for revised estimates.

This article discusses the development of an optimal variable-pitch controller for floating, axial-flow marine turbines. Recently, OpenFAST, an open-source wind turbine modeling tool, has been extended to model marine turbines. A controller is necessary to simulate marine turbines for different load cases using OpenFAST, which greatly impacts the performance of the energy system. Previous studies have designed controllers using a linearized model of the marine turbine, which can be timeconsuming and require the expertise of a control engineer. In this study, we use an automated approach that uses generic models of the marine turbine to identify the controller gains, which can expedite the process of designing a controller. Using an optimizer to identify the control system parameters can additionally improve the controller's performance. The optimal controller tuned using such an approach results in a 20% reduction in the towerbase damage equivalent loading and better tracking of the rated generator speed and power.

The American WAKE ExperimeNt (AWAKEN) is a multi-institutional field campaign focused on gathering critical observations of wind farm-atmosphere interactions. These interactions are responsible for a large portion of the uncertainty in wind plant modeling tools that are used to represent wind plant performance both prior to construction and during operation and can negatively impact wind energy profitability. The AWAKEN field campaign will provide data for validation, ultimately improving modeling and lowering these uncertainties. The field campaign is designed to address seven testable hypotheses through the analysis of the observations collected by numerous instruments at 13 ground-based locations and on five wind turbines. The location of the field campaign in Northern Oklahoma was chosen to leverage existing observational facilities operated by the U.S. Department of Energy Atmospheric Radiation Measurement program in close proximity to five operating wind plants. The vast majority of the observations from the experiment are publicly available to researchers and industry members worldwide, which the authors hope will advance the state of the science for wind plants and lead to lower cost and increased reliability of wind energy systems. (C) 2024 Author(s).

Turbulent and gusty wind conditions can cause generator overspeed peaks to exceed a threshold that then lead to wind turbine shutdowns, which then decrease the energy production of the wind turbines. We derive so-called "gust measures" that predict when generator overspeed peaks may occur. These gust measures are then used to develop advanced controllers to mitigate generator overspeed peaks so that wind turbines can operate more robustly in difficult wind conditions without exceeding generator overspeed thresholds that would lead to turbine shutdown events. The advanced controllers are demonstrated in nonlinear aeroelastic simulations using the open-source wind turbine simulation tool OpenFAST. To increase the realism of the simulations, they are run using field-replicated wind conditions and a wind turbine model based on data from an experimental field campaign on a downscaled demonstrator of a novel extreme-scale, two-bladed, downwind rotor design.

We present a control co-design software framework that can be used to optimize floating wind turbines and their controllers. Because this framework has many options for design variables, constraints, and merit figures, along with modeling fidelity levels, we seek to demonstrate best practices for using the tool while designing a floating platform for the new 22 MW offshore reference wind turbine developed within the International Energy Agency Wind Technology Commercialization Programme 55 on Reference Wind Turbines and Farms. During these studies, we evaluate the use of different simulation fidelity levels, the effect of using different load cases for controller tuning, and the difference between sequential and simultaneous control co-design solutions. Based on these efforts, we suggest using an algorithm that performs an initial search of the design space before optimization. We find that solving smaller optimization problems, in a sequential manner, leads to more reliable outcomes in fewer iterations than larger, simultaneous control co-design solutions. However a simultaneous CCD solution produces a platform with a 2% lower mass than the sequential CCD outcome.