Giant magnetoresistive (GMR) and tunneling magnetoresistive (TMR) spin valve sensors with a vortex-state free layer have been studied using resistance and noise measurements for temperatures from 50 to 400 K. A vortex-state free layer enables high saturation fields of the sensor while strongly reducing the phase noise and enabling a theoretically hysteresis-free transfer curve. The results show that the noise in both sensor types peaks at a temperature of about 200 K. Measurements in a saturated state enable a separation of electric and magnetic noise contributions and show that in contrast to TMR, both electric and magnetic noise contributions decrease with temperature for the GMR sample.

Magnetoresistive sensors based on giant magnetoresistance (GMR) or tunnel magnetoresistance (TMR) play a major role towards the miniaturization in the industrial society. Typically, spin-valve-type magnetoresistive sensors are embedded in a Wheatstone bridge configuration with rectangular, meander-like or elliptically shaped thin film elements. Such elements usually switch via multi-domain, C- or S-shaped magnetization states and, therefore, often exhibit an open non-linear hysteresis curve. Linearity and hysteretic effects are key features in the improvement of such sensors. We will present a different approach by using circularly shaped elements exhibiting a different magnetization state of a magnetic vortex [1]. This is one of the fundamental magnetization ground states occurring in disk-shaped thin film elements and is characterized by minimization of the demagnetizing energy at the expense of exchange energy. Experimental data were generated on electrically contacted GMR and TMR disks which were fabricated by optical lithography. The following advantages will be discussed and compared to standard elliptical sensor elements. (a) The vortex state shows essentially no hysteresis in the minor loop. (b) Since the vortex nucleation happens prior to the zero field, the M(H=0)=0 crossing is independent of history. (c) The critical fields can be easily controlled by the element geometry. (d) The noise is low. All characteristic experimental values have been determined in dependence of free layer thickness, disk diameter and temperature. These findings are discussed in the frame of the semi-analytical rigid-vortex-model [2] and micromagnetic simulations. The financial support by the Austrian Federal Ministry of Science, Research and Economy and the Christian Doppler Research Association in Austria is gratefully acknowledged. [1] D. Suess, A. Bachleitner-Hofmann, A. Satz, H. Weitensfelder, C. Vogler, F. Bruckner, C. Abert, K. Prügl, J. Zimmer, C. Huber, S. Luber, W. Raberg, T. Schrefl, H. Brückl, „Topologically Protected Vortex Structures to Realize Low-Noise Magnetic Sensors with High Linear Range”, Nature Electronics 1, 362 (2018) [2] K. Y. Guslienko et al., “Magnetization reversal due to vortex nucleation, displacement, and annihilation in submicron ferromagnetic dot arrays”, Phys. Rev. B 65 (2001)

The spin valve principle is the most prominent sensor design among giant- (GMR) and tunneling (TMR) magnetoresistive sensors. A new sensor concept with a disk shaped free layer enables the formation of a flux-closed vortex magnetization state if a certain relation of thickness to diameter is given. The low frequency noise of current-in-plane GMR sensing elements with different free layer thicknesses at different external field strengths has been measured. The measurements of the 1/f noise in external fields enabled a separation of magnetic and electric noise contributions. It has been shown that while the sensitivity is increasing with a decreasing element thickness, the pink noise contribution is increasing too. Still the detection limit at low frequencies is better in thinner free layer elements due to the higher sensitivity.

Magnetoresistive spin valve sensors based on the giant- (GMR) and tunnelling- (TMR) magnetoresisitve effect with a flux-closed vortex state free layer design are compared by means of sensitivity and low frequency noise. The vortex state free layer enables high saturation fields with negligible hysteresis, making it attractive for applications with a high dynamic range. The measured GMR devices comprise lower pink noise and better linearity in resistance but are less sensitive to external magnetic fields than TMR sensors. The results show a comparable detectivity at low frequencies and a better performance of the TMR minimum detectable field at frequencies in the white noise limit.

Micromagnetic sensors play a key role in a variety of industries, including the automotive industry, where they are used, for example, for speed and position detection. The adoption of emerging magnetoresistive sensor technology such as anisotropic magnetoresistance, giant magnetoresistance and tunnel magnetoresistance sensors is driven principally by their enhanced sensitivity and improved integration capabilities compared with conventional Hall effect sensors. At the heart of such sensors is a microstructured ferromagnetic thin-film element that transduces the magnetic signal, but these elements often exhibit a nonlinear hysteresis curve and the performance of the sensors is limited by magnetic noise. Here, we examine the origin of magnetic noise in magnetoresistive sensors and show that a topologically protected magnetic vortex state in the transducer element can be used to overcome these limitations. Using analytic and micromagnetic models, we find that the noise is due mainly to irreproducible magnetic switching of the transducer element at external fields that are close to the Stoner–Wohlfarth switching field. Then, using a flux-closed vortex configuration, we develop a giant magnetoresistance sensor layout that, compared to existing state-of-the-art sensors, has lower magnetic noise, a linear regime that is around an order of magnitude higher and negligible hysteresis.

Within this work a passive and wireless magnetic sensor, to monitor linear displacements, is proposed. We exploit recent advances in 3D printing and fabricate a polymer bonded magnet with a spatially linear magnetic field component corresponding to the length of the magnet. Regulating the magnetic compound fraction during printing allows specific shaping of the magnetic field distribution. A giant magnetoresistance magnetic field sensor is combined with a radio-frequency identification tag in order to passively monitor the exerted magnetic field of the printed magnet. Due to the tailored magnetic field, a displacement of the magnet with respect to the sensor can be detected within the sub-mm regime. The sensor design provides good flexibility by controlling the 3D printing process according to application needs. Absolute displacement detection using low cost components and providing passive operation, long term stability, and longevity renders the proposed sensor system ideal for structural health monitoring applications.

Micromagnetic sensors play a major role towards the miniaturization in the industrial society. The adoption of new and emerging sensor technologies like anisotropic magnetoresistance (AMR), giant magnetoresistance (GMR) and tunnel magnetoresistance (TMR) sensors are mainly driven by their integrability and enhanced sensitivity. At the core of such sensors, a microstructured ferromagnetic thin film element transduces the magnetic signal. Such elements usually switch via multi-domain, C- or S-shaped magnetization states and, therefore, often exhibit an open non-linear hysteresis curve. Linearity and hysteretic effects, as well as magnetic noise are key features in the improvement of such sensors. Here, we report on the physical origin of these disturbing factors and the inherent connection of noise and hysteresis. Critical noise sources are identified by means of analytic and micromagnetic models. The dominant noise source is due to irreproducible magnetic switching of the transducer element at external fields close to the Stoner Wohlfarth switching field. Furthermore, a solution is presented to overcome these limiting factors: a disruptive sensor design is proposed and analyzed which realizes a topologically protected magnetic vortex state in the transducer element. Compared to state of the art sensors the proposed sensor layout has negligible hysteresis, a linear regime about an order of magnitude higher and lower magnetic noise making the sensor ideal candidate for applications ranging from automotive industry to biological application.