The motivation of this research was to assess the possibility of speed control for the selected pressure-compensated pump. Measured static characteristics of an axial piston pump with pressure compensation are presented in the paper. Based on these characteristics, the pump efficiencies are determined. The characteristics and efficiencies are determined for the different pump outlet pressures, pump speeds, relative displacements and for the different pressures set at the pressure compensator. In addition, the different methods of pump control were compared. These are displacement control, speed control and both controls. The efficiency of each control method was compared based on the determined mechanical input power at the pump drive shaft. By comparing these control methods, it was found that the combination of both control methods can achieve up to 93% savings of mechanical power in the controlled state (stand-by state). Also, the adverse effects resulting from each control method that reduces pump efficiency were defined.

The effective and reliable performance of any pump can be significantly impacted by the piping system design. One of the essential points is the pump suction pipe. Poor design and dimension of the suction piping can lead to cavitation in the pump which affects its head and efficiency. The primary objective is to reduce the hydraulic losses of the suction piping in order to maintain a Net Positive Suction Head required by the pump. Suction piping is recommended to be short and straight, and branch connections, valves and elbows should be avoided, which is not always possible. In addition, cavitation can occur in the actual hydraulic elements installed on the pump suction. This work is focused on the investigation of cavitating hydraulic element in the suction pipe on the pump performance. A converging-diverging nozzle with a circular cross-section was used for this purpose. A straight pipe segment of constant diameter and the same length was used for comparison. Both elements were characterized by the loss coefficient and the cavitation number. Their influence on the pump head and the Net Positive Suction Head Available (NPSHA) was investigated.

Views Icon Views Article contents Figures & tables Video Audio Supplementary Data Peer Review Share Icon Share Twitter Facebook Reddit LinkedIn Tools Icon Tools Reprints and Permissions Cite Icon Cite Search Site Citation Jana Jablonská, Lukáš Pastrňák, Milada Kozubková, Lukáš Dvořák; Determination of a design parameter for slide valve using CFD. AIP Conf. Proc. 14 February 2023; 2672 (1): 020004. https://doi.org/10.1063/5.0120366 Download citation file: Ris (Zotero) Reference Manager EasyBib Bookends Mendeley Papers EndNote RefWorks BibTex toolbar search Search Dropdown Menu toolbar search search input Search input auto suggest filter your search All ContentAIP Publishing PortfolioAIP Conference Proceedings Search Advanced Search |Citation Search

The identification of cavitation is very important in technical practice for operational and especially economic reasons. The article deals with the use of another way to measure noise during cavitation. The current approach of measuring noise with an intensity probe is used in practice for identification, but it does not immediately address the position of the cavitation source for a given frequency range. Measurement by an acoustic camera is not entirely common in practice, but it allows to determine the location of the noise source for a given frequency range. To test the acoustic camera, the authors focused on the cavitating flow in a hydraulic circuit with three previously tested nozzles. Noise was measured for these nozzles using an acoustic intensity probe with two microphones. The results were evaluated by statistical methods and compared with measurements using an acoustic camera. The aim of the article is to point out the advantages of using this approach for accurate area identification of the problem. Research background: The work is focused on the issue of cavitation and its identification in the hydraulic circuit. For cavitation research, a variant of cavitation identification by noise was chosen. However, this measurement brings problems that are only revealed through more sophisticated and accurate measurements. Purpose of the article: The purpose of the article is to point out other possibilities of measuring cavitation noise using modern technologies and subsequently verify the results. Methods: Metody: A common way of measuring noise is to measure it with a suitably located acoustic intensity probe. A more modern approach is area noise measurement. Measurement methodology and benefits are described. Findings & Value added: The commonly used way of measuring noise using an acoustic intensity probe has proved to be insufficient, as it is not possible to distinguish the location of sources in the case of complex measurements. When using an acoustic camera, there are more sources of noise in a given circuit and they are detected according to the required frequencies in different places than expected. The article points out the specific identification of noise sources using the frequency spectrum of noise for selected elements.

The paper deals with the flow of oil through an experimental hydraulic circuit with a convergent divergent nozzle with a circular cross-section. Under different physical conditions, i.e. changes in pressure, flow and temperature, the formation and development of cavitation is monitored. As it is a highly dynamic flow in a transparent nozzle, cavitation is monitored using a high-speed camera and the frequency of formation and dissolution of the cavitation bubble and the movement of the cavitation cloud is then determined. The authors deal with the issue of the amount of dissolved or undissolved air in the hydraulic oil. Both variants of air influence the formation, development and size of the cavitation area. This cavitation is in this case called air cavitation. In technical practice, the issue of air cavitation is relevant, especially in the pump suction, where vacuum, leaks and hence air intake may occur.

This paper deals with CFD incorporation in a process of designing inducer with variable pitch. The introductory part is devoted to the theory of centrifugal pumps, cavitation and inducer itself followed by a description of the mathematical models of turbulence, multiphase fluid and cavitation. The main part of this paper consists of CFD evaluation, first, of inducer itself, later in application with centrifugal pump with regards to cavitation properties with and without the aplication of inducer, for interest, the comparison with different type of inducer, with constatnt pitch, is also included. At the end of this paper the advantages and some disadvantages are given for CFD based design of the hydrodynamic machines.

Today, the correct understanding of the issue of oil and water cavitation is important due to the growing demands on working conditions in hydraulic systems (pressure and flow rate). This article deals with the measurement and subsequent mathematical modeling of cavitation in a convergent-divergent nozzle of circular cross-section. Cavitation depends on the physical properties of the flowing medium as a function of temperature. Usually, cavitation in water is defined by a two-phase flow of water and vapor, but the air contained in the water significantly affects cavitation. There is usually no vapor cavitation in the oil. Far more often, cavitation in oil is caused by the air it contains. For comparison, cavitation in water and oil was generated in experiments with an identical nozzle. The measurement was used to define boundary conditions in mathematical models and to verify simulations. The problem of cavitation was solved by three variants of multiphase flow, single-phase flow (water, oil), two-phase flow (water–vapor, oil–air) and three-phase flow (water–vapor–air, oil–vapor–air). A turbulent model with cavitation was used for all variants. The verification of simulations shows that for water cavitation it is necessary to use a three-phase model (water, vapor, air) and for oil cavitation a two-phase model (oil, air) is sufficient. The measurement results confirm the importance of the air phase in modeling cavitation in both water and oil.

This paper deals with a mathematical modeling of flow stability of Newtonian and non-Newtonian fluids in the gap between two concentric cylinders, one of which rotates. A typical feature of the flow is the formation of a vortex flow, so-called Taylor vortices. Vortex structures are affected by the speed of the rotating cylinder and the physical properties of the fluids, i.e., viscosity and density. Analogy in terms of viscosity is assumed for non-Newtonian and magnetorheological fluids. Mathematical models of laminar, transient and turbulent flow with constant viscosity and viscosity as a function of the deformation gradient were formulated and numerically solved to analyze the stability of single-phase flow. To verify them, a physical experiment was performed for Newtonian fluids using visualizations of vortex structures-Taylor vortices. Based on the agreement of selected numerical and physical results, the experience was used for numerical simulations of non-Newtonian magnetorheological fluid flow.

The hydraulic equipment and elements are designed so that the flow is not significantly affected by the content of gases in the fluid. In the case of cavitation, there is a change in the volumetric amount of gas, which in water is due to the air and water vapour present, and in the case of oils, especially the air content. This phenomenon causes a significant change in the loss coefficient of the element. The problem of cavitation is solved in the literature for water flow, for other hydraulic fluids (e.g. hydraulic oils operated at different temperatures) the problem is still not solved to a sufficient extent. The article deals with the issue of cavitation in systems in which different types of liquids are used. In the introduction, the physical properties of the used liquids are evaluated, because they significantly influence the origin and development of cavitation. Subsequently, an experimental device with a transparent nozzle is described, on which the measurement. The dependence of the loss coefficient and the cavitation number on the Reynolds number is evaluated. Cavitation is evaluated by a high-speed camera, where it is possible to monitor the behaviour of the cavitation cloud.

The research of liquids composed of two (or more) mutually immiscible components is a new emerging area. These liquids represent new materials, which can be utilized as lubricants, liquid seals or as fluid media in biomechanical devices. The investigation of the problem of immiscible liquids started some years ago and soon it was evident that it will have a great application potential. Recently, there has been an effort to use ferromagnetic or magnetorheological fluids in the construction of dumpers or journal bearings. Their advantage is a significant change in dynamic viscosity depending on magnetic induction. In combination with immiscible liquids, qualitatively new liquids can be developed for future technologies. In our case, immiscible fluids increase the dynamic properties of the journal hydrodynamic bearing. The article focuses on the stability of single-phase and subsequently multiphase flow of liquids in the gap between two concentric cylinders, one of which rotates. The aim of the analysis was to study the effect of viscosity and density on the stability/instability of the flow, which is manifested by Taylor vortices. Methods of experimental and mathematical analysis were used for the analysis in order to verify mathematical models of laminar and turbulent flow of immiscible liquids.

When designing pipeline networks, the knowledge of loss coefficient respectively resistance coefficient when flowing through various types of fluids through hydraulic elements, e.g. control valves, which are often used in the engineering and energy industry. Their specification is performed mainly experimentally. However, there are applications where the experimental approach of their determination is unrealistic and then mathematical methods can be considered. The article presents a methodology for determining the static characteristics of the DN25 control valve for different opening. The measurement of the characteristics was performed with an incompressible flowing medium - water and with a compressible flowing medium - air. Subsequently, a comparison of measurement and evaluation of loss and flow coefficients was performed. The measured values will be further used to verify the results of modelling and to precisely define mathematical models, so that the models can be subsequently used at vapour flow, where the experimental method of determination is difficult. Frequent applications are found in the flow of saturated and superheated vapour through control valves.

When dealing with dynamic issues, we often encounter problems of hydraulic shock (water hammer) and cavitation causing distortion of the surrounding material, destruction of material, accompanied by sounds and vibrations. These dynamic behavior of the liquids is due to the presence of gases in the liquid, especially air, vapor and possibly other gases in smaller quantities. The density of such a liquid is assumed to be a function of a liquid elastic modulus depending on pressure or it is defined as the density of a multiphase mixture of incompressible liquid and compressible gases (vapour, air) depending on pressure too. The article is focused on specification of mathematical models of multiphase flow for piping (one dimensional) hydraulic systems and spatial (three dimensional) hydraulic elements and systems. The electrohydraulic analogue (Matlab-SimHydraulics) method and finite volume method (Ansys-Fluent) are used for illustrative fluid dynamics tasks.

Two methods are generally possible to design and optimize hydraulic components and devices. The classic method is the experimental method. In the hydraulic laboratories, various models of components and devices are examined to understand their basic properties, to verify proposed assumptions, or to alter derived theoretical equations to equations that approximate reality, etc. In some cases, which are very difficult to solve theoretically, or even yet unsolvable, you can only get the values you need using an experiment. However, not all phenomena can be described through models. Mathematical-physical modeling is a method by which Mathematical models based on the application of physical laws and phenomena can achieve the necessary results. These mathematical models consist of the definition of equations describing the given processes, which must be solved by means of numerical methods. Fluent, CFX Computerized software is used to solve the problem. Simulation can be performed within these softwares, which allows to evaluate different variables in a short period of time, to change the design of the element to suit the application, etc. However, it is a prerequisite to check the retained results by the experimental method. The method of optimizing the parameters and shapes of products and equipment is already an integral part of the design process. This achieve product shape improvement without having to produce A number of Prototypes, you can create a variety of variants and perform simulations for different conditions. At present, the mathematical optimization method is based on the principle of adjunction, which is part of the ANSYS Fluent solution, which means saving time and finance while achieving qualitative improvement. The article focuses on the theoretical and practical possibilities of using this method in the field of hydraulic elements.

The article describes mathematical simulation of flowing air through porous zone and water vaporisation from mentioned porous area which actually represents dried fibrous material - cotton towel. Simulation is based on finite volume method. Wet towel is placed in pipe and hot air flow through the towel. Water from towel is evaporated. Simulation of airflow through porous element is described first. Eulerian multiphase model is then used for simulation of water vaporisation from porous medium. Results of simulation are compared with experiment. Ansys Fluent 13.0 was used for calculation.

The paper deals with CFD simulation of SNCR technology with implemented CO temperature shift. The influence of CO on the SNCR process is described by empirical adjustment of kinetics parameters of chemical reactions. Results of CFD simulation were compared with results of experimental measurements. Although the proposed kinetics model of SNCR technology is simplified, it is able to describe reduction of NOx and other phenomena of SNCR with good precision. The model can be used to verify of injection levels and injection lances arrangement at design phase. Słowa kluczowe: technologia SNCR, roztwór mocznika, tlenki azotu NOx, usuwanie NOx

The article deals with experimental investigation of water cavitation in the convergent-divergent nozzle of rectangular cross-section. In practice, a quick and simple determination of cavitation is essential, especially if it is basic cavitation or cavitation generated additionally by the air being sucked. Air influences the formation, development and size of the cavity area in hydraulic elements. Removal or reduction of the cavity area is possible by structural changes of the element. In case of the cavitation with the suction air, it is necessary to find the source of the air and seal it. The pressure gradient, the flow, the oxygen content in the tank, and hence the air dissolved in the water, the air flow rate, the noise intensity and the vibration velocity on the nozzle wall were measured on laboratory equipment. From the selected measurements the frequency spectrum of the variation of the water flow of the cavity with cavitation without air saturation and with air saturation was compared and evaluated.

Migration can be a part of tourism related processes and there are numerous types of migrants and migration processes. The paper investigates the possible connection between tourism related processes and the present wave of migration to EU. Further, it analyzes the impact of the present migration processes on natural, cultural and social environment. Then the question of impact of migration and of war on a development of new forms of tourism and tourism related services. Finally, using the results of a survey, the impact of migration on the outlook and pre-purchase considerations of potential tourism clients is analyzed.

The article deals with dynamic flow behaviour in oil piping, modulus of fluid elasticity and its influence on the dynamic behaviour of hydraulic systems. In this paper, a methodology is to model the unsteady flow. Mathematical modeling of the measured pressures is implemented on the basis of the boundary conditions and is carried out in program Matlab SimHydraulics. The comparison results are in agreement.

The creation and extinction of bubbles is a very fast process that can be observed by a high-speed camera. The article deals with the visualization of gas bubbles and investigates the formation and collapse of cavitation bubbles in a convergent-divergent nozzle of a rectangular cross section. Measurement values are then used as boundary conditions for mathematical modeling. Comparison of the bubble velocities with the 3D mathematical model of the mixture flow (water - vapor - air) is performed.

The article deals with the cavitation phenomenon affected by full and partial wetting of the wall. For the numerical computation of flow in the Laval nozzle the Schnerr-Sauer cavitation model was tested and was used for cavitation research of flow within the nozzle considering partial surface wetting. The coefficient of wetting for various materials was determined using experimental, theoretical and numerical methods of fluid flow due to partial surface wetting.